刷题
导入试题
【单选题】
异步电动机在启动瞬间,启动电流很大,约为额定电流的___。
A. 2~3
B. 3~4
C. 4~7
D. 7~10
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
C
解析
暂无解析
相关试题
【单选题】
高压配电装置与低压配电装置如在同一室内单列布置时,高压开关柜与低压配电屏之间的距离应不小于___m。
A. 0.5
B. 0.6
C. 1
D. 2
【单选题】
接地装置是防雷装置的重要组成部分,作用是限制防雷装置的___。
A. 接触电压
B. 对地电压
C. 跨步电压
D. 泄露电压
【单选题】
进行心肺复苏应将伤员平放___在硬地。
A. 仰卧
B. 俯卧
C. 侧卧
D. 无要求
【单选题】
绝缘靴可做作为防护___的基本安全用具。
A. 跨步电压
B. 接触电压
C. 泄漏电流
D. 剩余电流
【单选题】
淡蓝色绝缘导线只用于___。
A. 相线
B. 保护中性线
C. 中性线
D. 保护线
【单选题】
运行中的变压器梯子上应悬挂___标标牌。
A. 止步,高压危险!
B. 从此上下
C. 已接地
D. 禁止攀登,高压危险
【单选题】
电路发生短路时,往往因___过大引起电器和电气线路损坏或火灾。
A. 电压
B. 电阻
C. 功率
D. 电流
【单选题】
___是指大小和方向随时间作周期性变化的电流。
A. 直流电
B. 交流电
C. 脉动交流电
D. 恒稳直流电
【单选题】
发电厂和变电站的电气值班人员必须熟悉___。
A. 两票三制
B. 工作票
C. 操作票
D. 电气设备
【单选题】
___kg以下灯具可采用软导线自身吊装,吊线盒及灯头两端应做防拉脱结扣。
A. 3
B. 2
C. 1
D. 0.5
【单选题】
热继电器的___应能在一定范围内调节以适应生产和使用要求。
A. 额定值
B. 动作值
C. 时间
D. 最小值
【单选题】
使用___类电动工具必须使用专用的安全隔离变压器。
A. I
B. II
C. III
D. II、III
【单选题】
电力变压器投入运行前,绝缘电阻应不低于出厂的___。
A. 0.7
B. 0.8
C. 0.9
D. 同期值
【单选题】
电气操作由___填写操作票。
A. 值班调度员
B. 值班负责人
C. 值长
D. 操作人
【单选题】
剩余电流动作保护装置主要用于___V以下的低压系统。
A. 220
B. 380
C. 660
D. 1000
【单选题】
测量电压时应根据被测电压的大小选用电压表的___。
A. 型式
B. 准确度
C. 内阻
D. 量程
【单选题】
断路器都装有___装置,因此它可以安全地带负荷合闸与分闸。
A. 电磁
B. 脱扣器
C. 灭弧
D. 过电流
【单选题】
对于阀型避雷器,每年雷雨季节前应测定绝缘电阻,测量时应用___V的摇表。
A. 500
B. 1000
C. 2500
D. 5000
【单选题】
___是由于雷击后,巨大的雷电流在周围空间产生迅速变化的强磁场引起的。
A. 直击雷电过电压
B. 电磁感应过电压
C. 静电感应过电压
D. 冲击过电压
【单选题】
导体的电阻与其材料的___和长度成正比。
A. 电压
B. 电流
C. 电阻率
D. 功率
【单选题】
速度继电器使用时,定子磁场的方向与电动机的旋转方向___。
A. 相反
B. 相同
C. 同相
D. 反相
【单选题】
电力电缆在支架上水平敷设时,支持点间的距离不应大于___m。
A. 0.4
B. 0.5
C. 0.8
D. 1
【单选题】
触电者处于高处,电源切断后触电者有高处坠落的可能,因此要采取___。
A. 预防措施
B. 保护措施
C. 抢救措施
D. 救护措施
【单选题】
采用电容补偿提高功率因数,___减少了,从而可改善电压的质量。
A. 功率损失
B. 电阻消耗
C. 电流损失
D. 电压损失
【单选题】
低压进户线管口对地距离应不小于___m。
A. 1.7
B. 2.2
C. 2.5
D. 2.7
【单选题】
绝缘手套的长度至少应超过手腕___cm。
A. 5
B. 10
C. 15
D. 20
【单选题】
在低压电气设备中,绝缘老化主要是___。
A. 电老化
B. 热老化
C. 化学老化
D. 应力老化
【单选题】
接闪杆主要用来保护___。
A. 建筑物
B. 电力线路
C. 构筑物
D. 露天变压器
【单选题】
线电压是相电压的___倍。
A. √2
B. 1/√2
C. √3
D. 1/√3
【单选题】
一般额定电压为380V的三相异步电动机,用___V的兆欧表测量绝缘电阻应大于0.5MΩ才可以使用。
A. 250
B. 500
C. 1000
D. 2500
【单选题】
电烙印是由于电流的___而造成的。
A. 电流的热效应
B. 电流的化学效应
C. 机械效应
D. 金属微粒渗入皮肤
【单选题】
笼形异步电动机转子铁芯一般都采用斜槽结构,其原因是___。
A. 简化制造工艺
B. 增加转子导体的有效长度
C. 增加转矩
D. 改善电动机的启动及运行性能
【单选题】
用户由专用的变压器供电时,如电动机容量小于变压器容量的___时,允许直接启动。
A. 0.1
B. 0.2
C. 0.3
D. 0.4
【单选题】
电路一般都是由电源、负载、中间环节___基本部分组成的。
A. 二个
B. 三个
C. 四个
D. 五个
【单选题】
中间继电器的触点数量比较多,可以将___信号转变为多路信号。
A. 多路
B. 三路
C. 二路
D. 一路
【单选题】
绝缘电阻通常用兆欧(摇表)表测定,摇表测量实际上是给被测物加上___。
A. 低压
B. 直流电压
C. 交流电压
D. 脉动电压
【单选题】
QJ23型单臂电桥的比率臂共有___固定的比例。
A. 4
B. 5
C. 6
D. 7
【单选题】
建筑物应根据其重要性,使用性质,发生雷电的可能性及后果,防雷标准要求分为___类。
A. 二
B. 三
C. 四
D. 五
【单选题】
螺旋式熔断器接线时要注意,电源进线接在瓷底座的___接线端上。
A. 金属螺纹壳
B. 顶芯
C. 任一接线端子
D. 无安全要求
【单选题】
绕线转子异步电动机与笼型异步电动机的主要区别是绕线转子异步电动机的转子采用___。
A. 三相笼形
B. 三相转子
C. 三相对称绕组
D. 三相非对称
推荐试题
【判断题】
用经纬仪和平行光管测量机床转台分度误差时,应用专用心轴配装在转台中心孔中将经纬仪和心轴紧固联接在一起
A. 对
B. 错
【判断题】
采用双螺母螺纹式调整滚珠丝杠轴向间隙的方法结构紧凑,调整方便,应用广泛
A. 对
B. 错
【判断题】
若自准直仪上读数鼓轮每格角值分度值为1",则其线值分度值可用0.05mm/m表示
A. 对
B. 错
【判断题】
所有的紫色酒精,在 1 米内不准点有明火,不准放在暖气片上
A. 对
B. 错
【判断题】
固定式装配适用于单件和小批量模具的装配,以及装配精度要求较高,需要调整的部位较多的装配
A. 对
B. 错
【判断题】
我国对企业发生的事故,坚持“四不放过”原则进行处理
A. 对
B. 错
【判断题】
齿轮的齿侧间隙分为12 个等级
A. 对
B. 错
【判断题】
在机械设备中,凸轮表面误差将会引起扭转振动
A. 对
B. 错
【单选题】
What happens to the status of users already logged into ESXi Shell when a vSphere administrator enables lockdown mode?___
A. Users remain logged in and can run commands, except to disable lockdown mode.
B. Users remain logged in and can run commands, including disabling lockdown mode.
C. Users are immediately logged out of ESXi Shell.
D. Users are logged out after a timeout specified by the vSphere administrator.
【单选题】
What is the effective vSphere licensing level during the 60 day evaluation period?___
A. vSphere Foundation Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
【单选题】
To comply with security requirements, an administrator with a vCenter Server Appliance needs to force logoff of the vSphere web client after 10 minutes of inactivity.What should the administrator do to meet the requirement?___
A. Edit: /var/lib/vmware/vsphere-client/webclient.properties, modify session.timeout=10
B. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=600
C. Edit: /var/lib/vmware/vsphere-client/webclient.properties modify session.timeout=600
D. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=10
【单选题】
An administrator enables High Availability (HA) on a Virtual SAN cluster.Which network is used for HA Network Heatbeat configuration?___
A. The Management network.
B. The vMotion network.
C. The Virtual SAN network.
D. The Provisioning Traffic network.
【单选题】
A user wants to monitor a business-critical virtual machine to ensure that it doesn't run out of resources. What metric could be monitored in vRealize Operations to address this concern?___
A. Time Remaining badge
B. Compliance badge
C. Reclaimable Waste badge
D. Density badge
【单选题】
An administrator has recently installed a new ESXi 6.x Host, and during the configuration notices sporadic network problems. To check whether the issue occurred sometime during the configuration, the administrator would like to reset the system.How can this be accomplished in the shortest amount of time?___
A. Run the ESXi installer again and reinstall the host.
B. Select the Reset System Configuration option from the vSphere Client when connected directly to the host.
C. From the
D. irect Console User Interface, select Reset System Configuration.
【单选题】
A vApp is running out of compute resources when overall activity is high within the resource pool. At other times, everything is fine.What should be done to resolve this issue?___
A. Increase the size of the resource pool Shares.
B. Set the vApp's CPU and Memory Reservation Type to Expandable.
C. Set the vApp's CPU and Memory Limit to Unlimited.
D. Create a new resource pool with the existing hardware configuration.
【单选题】
A virtual machine has been renamed and an administrator is unable to find files with the new virtual machine name in the datastore.What is the reason for this?___
A. The names of the files on the datastore do not change.
B. The names of the files on the datastore have been corrupted.
C. The virtual machine needs to be re-added to the inventory.
D. The Distributed Resource Scheduler moved the virtual machine to another host.
【单选题】
An administrator has configured network connectivity for a new virtual machine, as shown in the Exhibit.What will occur with the network traffic of this virtual machine when communicating externally from vSwitch1?___
A. The virtual machine will communicate on both uplinks
B. The virtual machine will only communicate on vmnic1
C. The virtual machine will only communicate on vmnic2
D. The virtual machine will fail to communicate externally
【单选题】
An administrator is unable to create the first group in a new vRealize Operations environment. What is the likely cause of the problem?___
A. There are no group types defined.
B. The group is not defined in SSO.
C. There are more than 32 group types defined.
D. The description for the group is not provided.
【单选题】
A new vApp was built and tested in the corporate headquarters datacenter running vSphere 6.x. What condition would explain why the virtual machine is failing to boot in an offsite datacenter running on vSphere 5.5?___
A. The virtual machine was built with the default hardware version.
B. The VMFS 5 datastore is not compatible with virtual machines configured with vSphere 6.x.
C. a
D. RS 5.5 cluster cannot run virtual machines configured with vSphere 6.x.
【单选题】
An administrator is evaluating whether to deploy vCenter Server on a Windows server or on a vCenter Server appliance. The administrator has the following requirements: <A web browser will be utilized to manage the vSphere environment.> <16 ESXi hosts will be deployed.> <Licenses must be shared with a vCenter Server at another site.> <An external Oracle 10g database server will be used to host the vCenter Server database.> Why will the administrator need to deploy vCenter Server on a Windows server?___
A. Linked Mode is a requirement for the solution.
B. Oracle 10g is a requirement for the solution.
C. The vSphere web client is a requirement for the solution.
D. Management of more than 5 hosts is a requirement for the solution.
【单选题】
What is a benefit of using VMware Data Protection ?___
A. Provides support for guest-level backups and restores of Microsoft SQL Servers, Exchange Servers, and Share Point Servers.
B. Provides support for advanced storage services including replication, encryption, deduplication, and compression.
C. Provides direct access to VDP configuration integrated into the vSphere Client.
D. Reduces disk space consumed by virtual machine data using deduplication.
【单选题】
An administrator enables vSphere High Availability (HA) on an existing cluster with a large number of hosts and virtual machines. The administrator notices that the setup of vSphere HA on some of the hosts is failing. What step, if taken, might resolve this issue?___
A. Increase the value of the config.vpxd.das.electionWaitTimeSec setting.
B. Set the value of vpxd.das.aamMemoryLimit to 256.
C. Set the value of the das.useDefaultIsolationAddress setting to False.
D. Increase the value of the das.iostatsinterval setting.
【单选题】
An ESXi 6.x host consists of 24 logical cores. Hyperthreading is enabled on the host. What is the maximum number of vCPUs that can be assigned to a virtual machine on this host?___
A. 24
B. 48
C. 64
D. 128
【单选题】
By default, each ESXi 6.x host is provisioned with a certificate from which root certificate authority?___
A. RedHat Certificate Authority
B. VMware Certificate Authority
C. DigiCert Certificate Authority
D. Verisign Certificate Authority
【单选题】
An administrator is adding an NFS datastore as shown in the Exhibit. What is the purpose of the Servers to be added list?___
A. It contains the IP addresses of the NFS Storage Server to provide multipathing capability.
B. It contains the IP addresses of the ESXi hosts that mount the datastore.
C. It contains the IP addresses used for
D. ynamic Discovery of targets.
【单选题】
An administrator reports that the System Event log data is only available for 24 hours when reviewing the Hardware Status tab. Which condition could be responsible for the loss of data?___
A. A Reset event log was executed.
B. The statistical collection level was set to a value of 1.
C. The boot disk of the host is corrupt.
D. Syslog has been configured at the vCenter Server level.
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
欢迎使用我爱刷题
×
微信搜索我爱刷题小程序
温馨提示
×
请在电脑上登陆“www.woaishuati.com”使用