【单选题】
正确的无线网络优化实施步骤为（ ）。___
A. 确认标准_分析问题_信号侧优化_测试效果_数据侧优化
B. 确认标准_分析问题_数据侧优化_信号侧优化_测试效果
C. 确认标准_分析问题_测试效果_信号侧优化_数据侧优化
D. 确认标准_分析问题_信号侧优化_数据侧优化_测试效果
E.
查看试卷，进入试卷练习
微信扫一扫，开始刷题
相关试题
【单选题】
以下哪种技术不是802.11n的核心技术？（ ）___
A. MIMO-OFDM
B. 信道捆绑技术
C. 帧聚合技术
D. 码分多址技术
E.
【单选题】
802.11g除去开销实际可获得的最大速率是多少？（ ）___
A. 5M~10M
B. 10M~15M
C. 15M~20M
D. 20M~24M
E.
【单选题】
WLAN中，基于WEB的认证流程，通过哪个服务器认证用户信息？（ ） ___
A. Radius服务器
B. Portal服务器
C. WEB服务器
D.
E. PG服务器 E.
【单选题】
WLAN中使用的AP分为大功率AP和小功率AP，其中大功率AP达到（ ）___
A. 100mv
B. 200mv
C. 500mv
D. 1000mv
E.
【单选题】
802.11n 2×2最大的数据传输速率可以达到___
A. 300Mbps
B. 150Mbps
C. 100Mbps
D. 50Mbps
E.
【单选题】
如AP安装位置的四周有特殊物品，如微波炉、无绳电话等他干扰源，一般要求AP至少离开此类干扰源（ ）米。___
A. 0.5~1
B. 1~2
C. 2~3
D. 3~4
E.
【单选题】
WLAN系统覆盖设计要求为98％以上区域的信号强度___(C)
A. 不得低于-65dBm
B. 不得低于-70dBm
C. 不得低于-75dBm
D. 不得低于-85dBm
E.
【单选题】
目前国际标准规定的无线产品最大发射功率为100mW，相当于（ ）。___
A. 1dbm
B. 10dbm
C. 20dbm
D. 30dbm
E.
【单选题】
下列认证方式是属于硬件认证而非用户认证的是（ ）。___
A. 共享密钥认证
B. EAP认证
C. MAC认证
D. SSID匹配
E.
【单选题】
下列哪种设备不会对WiFi产生干扰（ ）___
A. 微波炉
B. 蓝牙音箱
C. 周边AP
D. GSM手机
E.
【单选题】
用户终端连接到AP的（ ）从而接入网络___
A. SSID
B. SCUD
C. BSID
D. BSA
E.
【单选题】
带WiFi功能的HGU设备最适合哪种方式进行业务发放（ ）___
A. ONU的WEB
B. OLT的命令行
C. RMS
D.
E. MS E.
【单选题】
用户没有固话使用需求，但有上网和IPTV业务需求，并且希望手机和平板电脑可以连接WiFi上网，以下哪种方式可以满足用户需求（ ）___
A. 不带POTS口的HGU设备，宽带业务采用桥接WAN连接
B. 不带POTS口的HGU设备，宽带业务采用路由WAN连接
C. 带POTS口的HGU设备，宽带业务采用路由WAN连接
D. SFU设备，二层上网方式
E.
【单选题】
网关上配置路由wan连接，通过DHCP方式获取地址，网关上配置DHCP地址池IP为192.168.1.100-192.168.1.200，上层bras的DHCP地址池IP为10.10.100.100-10.10.10.200；PC1连接网关lan1口，此时PC拿到的IP地址是（ ）___
A. 192.168.1.2
B. 192.168.1.100
C. 10.10.100.2
D. 10.10.100.100
E.
【单选题】
802.11g物理层理论最大速率能达到多少？（ ）___
A. 11M
B. 54M
C. 108M
D. 600M
E.
【单选题】
WLAN采用的哪种信道复用方式（ ）___
A. CSMA/CA
B.
C. SMA/CB C.CSMA/CC
D. CSMA/CD
E.
【单选题】
两台无线网桥建立桥接，下列哪些信息必须相同。（ ）___
A. 信道
B. MAC地址
C. SSID
D. 设备序列号
E.
【单选题】
802.11帧结构中，有几个address？（ ）___
【单选题】
输出功率为100mW的802.11b/g产品覆盖距离理论值（ ）。___
A. 30米
B. 50米
C. 100米
D. 200米
E.
【单选题】
家庭 WiFi 测试规范中要求的测试内容主要包括信号强度和（ ）。___
A. 信号强度
B. ping网络质量
C. 信道干扰
D. 无线速率
E.
【单选题】
WiFi检查中主要测试（ ）和无线速率。___
A. 无线强度
B. ping值
C. 无线频宽
D. 信道干扰
E.
【单选题】
WLAN口状态灯（ ）表示无线接口已启动的___
A. 熄灭
B. 慢闪
C. 快闪
D. 常亮
E.
【单选题】
测试区域内无线信号场强为-55dBm，周围Wi-Fi信号较少，但测试下载速率只有实际宽带带宽的40%，此时要解决什么问题？（ ）___
A. 干扰
B. 终端性能
C. 组网设备性能
D. 提高带宽
E.
【单选题】
在用户家中进行无线网络评测时，对用户需连接使用的WIFI信号测试要求为目标覆盖区域内95%以上的位置，接受信号场强值（），信噪比SMR值应该大于-20db___
A. ≥-75dbm
B. ≥-65dbm
C. ≥-45dbm
D. ≥-35dbm
E.
【单选题】
判断无线网络质量的3个要素为：信号强度、信道干扰和（）___
A. 加密方式
B. 信道频宽
C. 多线程下载速率
D. 无线中继
E.
【单选题】
能独立进行管理及配置，但无法统一管理的组网设备，一般我们称它为（）___
A. 胖AP
B. 瘦AP
C. WIFI放大器
D. AC管理器
E.
【单选题】
如果采用+路由器+AC+POE交换机+FIT AP方式组网，智能终端设备入网后获取的IP 地址应该是从哪个设备上分配得到的（ ）___
A. 天翼网关
B. 无线路由器
C. AC
D. AP 面板
E.
【单选题】
两台无线设备是通过( )建立桥连接 ___
A. MAC地址
B. IP地址
C. 设备的标志号
D. 设备的型号
E.
【单选题】
两台无线网桥建立桥接，（ ）必须相同___
A. SSID、信道
B. 信道
C. SSID、MAC地址
D. 设备序列号、MAC地址
E.
【单选题】
两个路由器通过无线实现同一网段，同SSID，这种组网方式为以下哪种（）___
A. ELINK组网
B. 无线桥接
C. 有线桥接
D. 同时PPPOE拨号
E.
【单选题】
因为AP是共享设备，所以为了更好地提供无线客户端的接入带宽，建议一个AP最多可带（ ）个用户。___
A. 10-15
B. 20-30
C. 30-50
D. 50-100
E.
【单选题】
下列服务中，如果不开启则无法使用windows配置无线网络是（）___
A. WZC
B. Remote Registry
C. Messenger
D. Teinet
E.
【单选题】
下列哪种通信技术不属于低功率短距离的无线通信技术？（ ）。___
A. 广播
B. 超宽带技术
C. 蓝牙
D. Wi-Fi
E.
【单选题】
下列关于路由器的安装说法错误的是（ ）___
A. 路由器应尽可能安装在预定覆盖区域的中心位置
B. 路由器不应该安装在带金属覆盖壳的多媒体箱中
C. 路由器网络接入的方式主要有PPPoE拨号，动态获取IP地址和静态IP地址三种
D. 路由器的发射功率大小是不可调节的
E.
【单选题】
某家庭宽带用户使用路由器上网，必须在电脑本地网卡手动设置IP地址、掩码、网关、DNS后才能上网，最可能原因是（ ）。___
A. 客户电脑网卡故障，无法自动获取IP地址
B. 路由器性能太差、连接的用户太多，自动分配不了IP地址
C. 路由器未启用DHCP服务器功能
D. 客户使用的网线质量太差，致使无法自动分配到IP地址
E.
【单选题】
某用户平时使用路由器上网，每天在晚上8:30之后就无法上网，直到后一天早上 8:00才可以上网，同楼层其他用户正常，最可能的原因是（ )___
A. 我司的网络出口带宽小、在晚上高蜂期出现拥塞
B. 我司的0NU及其以上设备或线路不稳定导致经常断线
C. 客户路由器设置了时间策略，只许在8:00-20:30 能上网
D. 客户电脑中病毒导致
E.
【单选题】
使用简易式POE反向供电技术，在终端处需使用（ ）为其供电。___
A. POE母头
B. POE公头
C. POE交换机
D. 12V电源
E.
【单选题】
EOC组网是指基于（）的组网技术___
A. 电力线
B. 同轴电缆
C. 室内暗管
D. 无线协议
E.
【单选题】
EOC技术，是利用（ ） 来传输 （ ）信号。___
A. 电话线；以太网
B. 网线；CATV
C. 有线电视同轴线；以太网
D. 网线；WLAN
E.
【单选题】
EOC技术，主要作用就是滤波，将高频信号和低频信号分开，将同轴线传输的（ ）转换以太网传输的信号。___
A. 高频信号
B. 低频信号
C. 音频信号
D. 传输信号
E.
推荐试题
【单选题】
A new vApp was built and tested in the corporate headquarters datacenter running vSphere 6.x. What condition would explain why the virtual machine is failing to boot in an offsite datacenter running on vSphere 5.5?___
A. The virtual machine was built with the default hardware version.
B. The VMFS 5 datastore is not compatible with virtual machines configured with vSphere 6.x.
C. a
D. RS 5.5 cluster cannot run virtual machines configured with vSphere 6.x.
【单选题】
An administrator is evaluating whether to deploy vCenter Server on a Windows server or on a vCenter Server appliance. The administrator has the following requirements: <A web browser will be utilized to manage the vSphere environment.> <16 ESXi hosts will be deployed.> <Licenses must be shared with a vCenter Server at another site.> <An external Oracle 10g database server will be used to host the vCenter Server database.> Why will the administrator need to deploy vCenter Server on a Windows server?___
A. Linked Mode is a requirement for the solution.
B. Oracle 10g is a requirement for the solution.
C. The vSphere web client is a requirement for the solution.
D. Management of more than 5 hosts is a requirement for the solution.
【单选题】
What is a benefit of using VMware Data Protection ?___
A. Provides support for guest-level backups and restores of Microsoft SQL Servers, Exchange Servers, and Share Point Servers.
B. Provides support for advanced storage services including replication, encryption, deduplication, and compression.
C. Provides direct access to VDP configuration integrated into the vSphere Client.
D. Reduces disk space consumed by virtual machine data using deduplication.
【单选题】
An administrator enables vSphere High Availability (HA) on an existing cluster with a large number of hosts and virtual machines. The administrator notices that the setup of vSphere HA on some of the hosts is failing. What step, if taken, might resolve this issue?___
A. Increase the value of the config.vpxd.das.electionWaitTimeSec setting.
B. Set the value of vpxd.das.aamMemoryLimit to 256.
C. Set the value of the das.useDefaultIsolationAddress setting to False.
D. Increase the value of the das.iostatsinterval setting.
【单选题】
An ESXi 6.x host consists of 24 logical cores. Hyperthreading is enabled on the host. What is the maximum number of vCPUs that can be assigned to a virtual machine on this host?___
【单选题】
By default, each ESXi 6.x host is provisioned with a certificate from which root certificate authority?___
A. RedHat Certificate Authority
B. VMware Certificate Authority
C. DigiCert Certificate Authority
D. Verisign Certificate Authority
【单选题】
An administrator is adding an NFS datastore as shown in the Exhibit. What is the purpose of the Servers to be added list?___
A. It contains the IP addresses of the NFS Storage Server to provide multipathing capability.
B. It contains the IP addresses of the ESXi hosts that mount the datastore.
C. It contains the IP addresses used for
D. ynamic Discovery of targets.
【单选题】
An administrator reports that the System Event log data is only available for 24 hours when reviewing the Hardware Status tab. Which condition could be responsible for the loss of data?___
A. A Reset event log was executed.
B. The statistical collection level was set to a value of 1.
C. The boot disk of the host is corrupt.
D. Syslog has been configured at the vCenter Server level.
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
【单选题】
An administrator is installing Windows into a virtual machine. The DVD has been mounted on the Host and configured for the virtual machine as shown in the Exhibit. Based on the exhibit, when the virtual machine is booted, why would it attempt to search for a PXE server? ___
A. The CD/DVD device is not connected.
B. The ISO is in the incorrect storage location.
C. The OS minimum requirements have not been met.
D. The CD/DVD device is not set to Client Device.
【单选题】
What component must be installed prior to deploying a vCenter Server in vSphere 6.x? ___
A. vCenter Identity Services
B. Platform Services Controller
C. vCenter Single Sign-On
D. Client Integration Plug-In
