【单选题】
无人机系统中，起降操作手一般不参与哪个阶段控制： ___
查看试卷，进入试卷练习
微信扫一扫，开始刷题
相关试题
【单选题】
多旋翼飞行器每个轴上，一般连接：___
A. 1个电调，1个电机
B. 2个电调，1个电机
C. 1个电调，2个电机
【单选题】
同一架多旋翼飞行器，在同样做好动力匹配的前提下：___
A. 两种桨效率一样高
B. 三叶桨效率高
C. 两叶桨效率高
【单选题】
在飞行中遇到飞机积冰时，驾驶员应注意： ___
A. 保持飞行高度和平飞姿态，尽快脱离积冰区
B. 及时有力地修正飞行姿态的偏差
C. 调整飞机马力，严格保持飞行高度和速度
【单选题】
多旋翼飞行器动力系统主要使用：___
A. 内转子电机
B. 外转子电机
C. 步进电机
【单选题】
如不考虑结构、尺寸、安全性等其它因素，单纯从气动效率出发，同样起飞重量的8轴飞行器与4轴飞行器：___
A. 4轴效率高
B. 效率一样
C. 8轴效率高
【单选题】
某多轴电机标有500KV字样，意义是指：___
A. 电机最大耐压500KV
B. 对应每V电压，电机提供500转转速
C. 对应每V电压，电机提供500000转转速
【单选题】
据统计，无人机系统事故60%以上发生在： ___
【单选题】
_______ 主要包括起飞场地标注、着陆场地标注、应急场地标注，为操作员提供发射与回收以及应急迫降区域参考。___
A. 场地标注
B. 任务区域标注
C. 警示标注
【单选题】
任何单位或个人设计民用航空器，应当向民航局申请：___
【单选题】
在大气层内，大气压强：___
A. 随高度增加而增加
B. 在不同温度层内随高度增加保持不变
C. 随高度增加而减小
【单选题】
在融合空域运行的Ⅻ类无人机机长，应至少持有：___
A. 航线运输驾驶员执照
B. 私照
C. 运动执照
【单选题】
在山地背风坡中的下降气流中飞行时，除造成飞机掉高度外，还可造成严重的危害的原因是：___
A. 地速减小
B. 空速表误差增大
C. 气压式高度表读数高于实际高度
【单选题】
以下哪种动力电池放电电流最大：___
A. 30000mAh，5C
B. 20000mAh，5C
C. 2Ah，30C
【单选题】
飞行中的多旋翼飞行器所承受的力和力矩不包括：___
A. 旋翼的反扭矩和桨叶力矩
B. 旋翼桨叶的铰链力矩
C. 自身重力
【单选题】
某多轴电机转速为3000转，是指：___
A. 每秒钟3000转
B. 每小时3000转
C. 每分钟3000转
【单选题】
发生在低层的风切变严重影响航空器的起降，将发生在这一层中的风切变称为低空风切变。低空风切变距地面一般约： ___
【单选题】
多旋翼飞行器螺旋桨从结构上说，更接近于：___
A. 风力发电机叶片
B. 直升机旋翼
C. 固定翼飞机螺旋桨
【单选题】
大多数多旋翼飞行器自主飞行过程中利用______实现位置感知：___
【单选题】
下列哪个选项中的直升机的分类方式是相同的：___
A. 单旋翼带尾桨无人直升机，共轴式双旋翼无人直升机，多轴无人飞行器
B. 微型直升机，轻型无人直升机，四轴飞行器
C. 3代直升机，变模态无人机旋翼机，复合无人旋翼机
【单选题】
一般锂聚合物电池上都有2组线，1组是输出线（粗，红黑各1根）；1组是单节锂电池引出线（细，与S数有关），用以监视平衡充电时的单体电压。下面说法正确的是：___
A. 6S电池有5根红色引出线，1根黑色引出线
B. 6S电池有6根引出线
C. 6S电池有7根引出线
【单选题】
起落航线飞行开始一转弯和结束四转弯的高度一般不得低于：___
【单选题】
多旋翼飞行器不属于以下哪个概念范畴：___
A. 自转旋翼机
B. 重于空气的航空器
C. 直升机
【单选题】
同样重量不同类型的动力电池，容量最大的是：___
A. 镍氢电池
B. 聚合物锂电池
C. 镍镉电池
【单选题】
用遥控器设置电调，需要：___
A. 接上电机
B. 断开动力电源
C. 断开电机
【单选题】
多旋翼飞行器是轴数越多载重能力越大：___
【单选题】
在飞行任务中，必须明确：___
A. 飞行任务、起飞时间、航线、高度、允许机长飞行的最低气象条件及其它相关事项
B. 飞行任务、机组人员、起飞时间、航线、高度、允许机长飞行的最低气象条件及其它相关事项
C. 飞行任务、起飞时间、航线、允许机长飞行的最低气象条件及其它相关事项
【单选题】
多旋翼飞行器的飞控指的是：___
A. 机载遥控接收器
B. 机载导航飞控系统
C. 机载任务系统
【单选题】
属于无人机飞控子系统功能的是：___
A. 导航控制
B. 任务信息收集和传递
C. 无人机姿态稳定与控制
【单选题】
以下哪种动力电池在没有充分放电的前提下，不能以大电流充电：___
A. 锂聚合物电池
B. 铅酸蓄电池
C. 镍镉电池
【单选题】
4轴飞行器有X模式和+模式两大类，其中：___
A. X模式操作性好
B. +模式操作性好
C. 两种模式操作性没有区别
【单选题】
获准飞出或者飞入中华人民共和国领空的航空器，实施飞出或者飞入中华人民共和国领空的飞行和各飞行管制区的飞行：___
A. 必须经由国务院，中央军委空中交通管制委员会批准
B. 必须经中国人民解放军空军批准
C. 必须经相关管制单位批准
【单选题】
多旋翼飞行使用的锂聚合物动力电池，其单体标称电压为：___
【单选题】
多旋翼飞行器，电调和电机一般通过三根单色线连接，如任意调换其中2根与电机的连接顺序，会出现：___
A. 该电机出现过热并烧毁
B. 该电机反向运转
C. 该电机停转
【单选题】
在温度不变的情况下，空气的密度与压力的关系：___
A. 与压力成反比
B. 与压力无关
C. 与压力成正比
【单选题】
大型无人机计算装载重量和重心的方法主要有：计算法、图标法和：___
【单选题】
电调上最粗的红线和黑线用来连接：___
A. 机载遥控接收机
B. 动力电池
C. 电动机
【单选题】
相对于传统直升机，多轴最大的优势是：___
A. 结构与控制简单
B. 气动效率高
C. 载重能力强
【单选题】
大气的组成是由：___
A. 78%的氮气，21%的氧气以及1%的其它气体组成
B. 75%的氮气，24%的氧气以及1%的其它气体组成
C. 78%的氮气，20%的氧气以及2%的其它气体组成
推荐试题
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
【单选题】
An administrator is installing Windows into a virtual machine. The DVD has been mounted on the Host and configured for the virtual machine as shown in the Exhibit. Based on the exhibit, when the virtual machine is booted, why would it attempt to search for a PXE server? ___
A. The CD/DVD device is not connected.
B. The ISO is in the incorrect storage location.
C. The OS minimum requirements have not been met.
D. The CD/DVD device is not set to Client Device.
【单选题】
What component must be installed prior to deploying a vCenter Server in vSphere 6.x? ___
A. vCenter Identity Services
B. Platform Services Controller
C. vCenter Single Sign-On
D. Client Integration Plug-In
【单选题】
What is a valid plug-in status for a plug-in that has been added to a vSphere client? ___
A. Disabled
B. Unknown
C. Stopped
D. Installed
【单选题】
Users of an application are reporting performance issues. The following performance values are observed in the vSphere Web Client: <Host CPU utilization is 90%> <Virtual Machine memory utilization is consistently greater than 90% CPU Ready values are higher than 20%> What could be the cause of the application performance issue? ___
A. The host is lacking the CPU resources required to meet the demand.
B. The host is lacking the memory resources required to meet the demand.
C. The virtual machine is lacking the CPU resources required to meet the demand.
D. The virtual machine is lacking the memory resources required to meet the demand.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is re-provisioning an ESXi host and moving it to another datacenter. Which DCUI option should the administrator use to revert the system configuration to the default settings? ___
A. Reset System Configuration
B. Rebuild Default System Configuration
C. Revert System Configuration
D. Renew Default System Configuration
【单选题】
An administrator has just completed installing an ESXi 6.x host, but doesn't know what address has been configured. Where is the ESXi host IP address configured? ___
A. RVC console
B. Direct Console User Interface
C. vSphere Web Client
D. vSphere Client
【单选题】
When is it possible to place a VMFS5 datastore in maintenance mode? ___
A. When it is a member of a Storage DRS cluster
B. When it is a member of Virtual SAN cluster
C. When it is a member of a multi-extent datastore
D. When it is a member of a Virtual Volume
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Which Single Sign-On deployment mode should an administrator use for two 6.x vCenter Servers configured with linked mode? ___
A. Basic Single Sign-On with vCenter Server Heartbeat
B. Multisite Single Sign-On
C. Basic Single Sign-On
D. Single Sign-On with Linked Mode
【单选题】
What is required when changing a virtual machine name using the vSphere Web Client? ___
A. Verify connectivity to the ESXi host where the virtual machine is running and its inventory list is accessible.
B. Verify in which datastore the virtual machine resides and that you have access and its inventory list is accessible.
C. Verify that virtual machine files are stored in the same datastore and can be accessed in the datastore browser list.
D. Verify the virtual machine is not running in Fault Tolerant mode and that it is not in a Distributed Resource Scheduler cluster.
