【填空题】
6KV 开关柜均设有“五防”机械闭锁装置，一般采用强制机械闭锁装置的闭锁功能是小车开关在合闸状态时不能___、接地刀闸在合闸状态时，小车开关不能推入___位置、开关在工作位置时，不能___接地刀闸、接地刀闸不合，不能打开开关柜___。
查看试卷，进入试卷练习
微信扫一扫，开始刷题
相关试题
【填空题】
所有隔离开关合上后，必须检查___接触良好。
【填空题】
合上接地刀闸前，必须确知有关各侧电源开关在___位置，并在验明___后进行。
【填空题】
如发生带负荷拉刀闸时，在未断弧前应迅速___，如已断弧则严禁重新合上。如发生带负荷合闸，则严禁重新___。
【填空题】
在回路中未设有开关时，可利用隔离开关进行拉合电压不超过 10KV、电流在___以下的环路均衡电流。
【填空题】
电缆线路的正常工作电压，不应超过电缆额定电压的___。
【填空题】
装设接地线的顺序是先装___，后装___。
【填空题】
断路器的用途是：正常时能___或断开电路；发生故障时，能自动___故障电流，需要时能自动重合，起到控制和保护两方面作用。
【填空题】
手动合隔离开关时，必须___果断，但合闸终了时不得___过猛，在合闸过程中产生电弧，也不准把隔离开关___。
【填空题】
手动切断隔离开关时，必须___而谨慎，但当拉开被允许的负荷电流时，则应___而果断，操作中若刀口刚离开时产生电弧则应立即___。
【填空题】
带电手动取下三相水平排列的动力熔断器时，应先取下___相，后取___相、上熔断器时与此相反。
【填空题】
在发电厂中，高压熔断器一般作为电压互感器的___侧保护，其熔丝电流一般为___A。
【填空题】
为防止电机受潮，设备停止运行时及时投入电机___。
【填空题】
高压手车式断路器的运行位置有：___位置、___位置、___位置。
【填空题】
两台变压器并联运行时，如果阻抗电压的百分值不相等，则会造成变压器之间负荷分配不均匀，其中一台变压器可能___，而另一台变压器欠载。其中，欠载的是阻抗电压的百分___的变压器，过载的是阻抗电压的百分较大的变压器。
【填空题】
厂备用电源自投装置中，均设有低电压启动部分，其启动条件为：本段厂用母线___、备用段母线___。
【填空题】
厂用电源的并联切换的优点是能保证厂用电的___，缺点是并联期间___，增大了对断路器断流能力的要求。但由于并联时间很短，发生事故的概率很小，所以在正常切换中被广泛采用。
【填空题】
厂用电源的串联切换过程是：一个电源切除后，才允许另一个电源___。
【填空题】
UPS 电源运行中全部失去，则必然造成___。
【填空题】
6KV 母线 TV 故障时，6KV 母线电压表指示___，“电压回路断线”光字牌亮。
【填空题】
电压互感器有明显故障时，___将电压互感器手车拉出。___用电压互感器的隔离开关隔绝故障电压互感器。
【填空题】
柴油发电机应定期实验，柴油发电空载运行后应检查柴油发电机运行正常且___、___正常。
【填空题】
柴油发电机连续启动三次失败，则发___信号，___柴油发电机启动。
【填空题】
当 UPS 逆变器故障时,UPS切换到___运行。
【填空题】
对于厂用电备自投的要求是只能动作___。
【填空题】
当发电机正常运行时，当备用电源无电压时，厂用电备自投装置___备自投投入。
【填空题】
当 UPS 工作电源整流器故障时，UPS 自动切至___经逆变器供电。
【填空题】
蓄电池是一种储能设备，它能把___能转变为___能储存起来；使用时，又把___能转变为___，通过外电路释放出来。
【填空题】
蓄电池在电厂中作为___和___的直流电源，具有电压稳定，供电可靠等优点。
【填空题】
220V直流动力母线电压应经常保持在___。
【填空题】
一组蓄电池的容量为 1200AH，若以 100A 的电流放电，则持续供电时间为___。
【填空题】
110V直流母线电压应经常保持在___。
【填空题】
充足电的铅蓄电池，如果放置不用，将逐断失去___，这种现象叫做蓄电池___。
【填空题】
蓄电池正常处于___方式，事故情况下处于___方式。
【填空题】
铅酸蓄电池在充电过程中，正极板有___析出，在负极板有___析出。
【填空题】
蓄电池放电时，端电压逐渐下降，当电瓶端电压下降到___V 后，则应停止放电，这个电压称为放电___电压。
【填空题】
110V直流控制母线电压应经常保持在___。
【填空题】
直流母线并列前，必须检查两组母线___，正、负极性___。
【填空题】
直流母线发生接地时应询问相关专业有无___。
推荐试题
【单选题】
What happens to the status of users already logged into ESXi Shell when a vSphere administrator enables lockdown mode?___
A. Users remain logged in and can run commands, except to disable lockdown mode.
B. Users remain logged in and can run commands, including disabling lockdown mode.
C. Users are immediately logged out of ESXi Shell.
D. Users are logged out after a timeout specified by the vSphere administrator.
【单选题】
What is the effective vSphere licensing level during the 60 day evaluation period?___
A. vSphere Foundation Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
【单选题】
To comply with security requirements, an administrator with a vCenter Server Appliance needs to force logoff of the vSphere web client after 10 minutes of inactivity.What should the administrator do to meet the requirement?___
A. Edit: /var/lib/vmware/vsphere-client/webclient.properties, modify session.timeout=10
B. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=600
C. Edit: /var/lib/vmware/vsphere-client/webclient.properties modify session.timeout=600
D. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=10
【单选题】
An administrator enables High Availability (HA) on a Virtual SAN cluster.Which network is used for HA Network Heatbeat configuration?___
A. The Management network.
B. The vMotion network.
C. The Virtual SAN network.
D. The Provisioning Traffic network.
【单选题】
A user wants to monitor a business-critical virtual machine to ensure that it doesn't run out of resources. What metric could be monitored in vRealize Operations to address this concern?___
A. Time Remaining badge
B. Compliance badge
C. Reclaimable Waste badge
D. Density badge
【单选题】
An administrator has recently installed a new ESXi 6.x Host, and during the configuration notices sporadic network problems. To check whether the issue occurred sometime during the configuration, the administrator would like to reset the system.How can this be accomplished in the shortest amount of time?___
A. Run the ESXi installer again and reinstall the host.
B. Select the Reset System Configuration option from the vSphere Client when connected directly to the host.
C. From the
D. irect Console User Interface, select Reset System Configuration.
【单选题】
A vApp is running out of compute resources when overall activity is high within the resource pool. At other times, everything is fine.What should be done to resolve this issue?___
A. Increase the size of the resource pool Shares.
B. Set the vApp's CPU and Memory Reservation Type to Expandable.
C. Set the vApp's CPU and Memory Limit to Unlimited.
D. Create a new resource pool with the existing hardware configuration.
【单选题】
A virtual machine has been renamed and an administrator is unable to find files with the new virtual machine name in the datastore.What is the reason for this?___
A. The names of the files on the datastore do not change.
B. The names of the files on the datastore have been corrupted.
C. The virtual machine needs to be re-added to the inventory.
D. The Distributed Resource Scheduler moved the virtual machine to another host.
【单选题】
An administrator has configured network connectivity for a new virtual machine, as shown in the Exhibit.What will occur with the network traffic of this virtual machine when communicating externally from vSwitch1?___
A. The virtual machine will communicate on both uplinks
B. The virtual machine will only communicate on vmnic1
C. The virtual machine will only communicate on vmnic2
D. The virtual machine will fail to communicate externally
【单选题】
An administrator is unable to create the first group in a new vRealize Operations environment. What is the likely cause of the problem?___
A. There are no group types defined.
B. The group is not defined in SSO.
C. There are more than 32 group types defined.
D. The description for the group is not provided.
【单选题】
A new vApp was built and tested in the corporate headquarters datacenter running vSphere 6.x. What condition would explain why the virtual machine is failing to boot in an offsite datacenter running on vSphere 5.5?___
A. The virtual machine was built with the default hardware version.
B. The VMFS 5 datastore is not compatible with virtual machines configured with vSphere 6.x.
C. a
D. RS 5.5 cluster cannot run virtual machines configured with vSphere 6.x.
【单选题】
An administrator is evaluating whether to deploy vCenter Server on a Windows server or on a vCenter Server appliance. The administrator has the following requirements: <A web browser will be utilized to manage the vSphere environment.> <16 ESXi hosts will be deployed.> <Licenses must be shared with a vCenter Server at another site.> <An external Oracle 10g database server will be used to host the vCenter Server database.> Why will the administrator need to deploy vCenter Server on a Windows server?___
A. Linked Mode is a requirement for the solution.
B. Oracle 10g is a requirement for the solution.
C. The vSphere web client is a requirement for the solution.
D. Management of more than 5 hosts is a requirement for the solution.
【单选题】
What is a benefit of using VMware Data Protection ?___
A. Provides support for guest-level backups and restores of Microsoft SQL Servers, Exchange Servers, and Share Point Servers.
B. Provides support for advanced storage services including replication, encryption, deduplication, and compression.
C. Provides direct access to VDP configuration integrated into the vSphere Client.
D. Reduces disk space consumed by virtual machine data using deduplication.
【单选题】
An administrator enables vSphere High Availability (HA) on an existing cluster with a large number of hosts and virtual machines. The administrator notices that the setup of vSphere HA on some of the hosts is failing. What step, if taken, might resolve this issue?___
A. Increase the value of the config.vpxd.das.electionWaitTimeSec setting.
B. Set the value of vpxd.das.aamMemoryLimit to 256.
C. Set the value of the das.useDefaultIsolationAddress setting to False.
D. Increase the value of the das.iostatsinterval setting.
【单选题】
An ESXi 6.x host consists of 24 logical cores. Hyperthreading is enabled on the host. What is the maximum number of vCPUs that can be assigned to a virtual machine on this host?___
【单选题】
By default, each ESXi 6.x host is provisioned with a certificate from which root certificate authority?___
A. RedHat Certificate Authority
B. VMware Certificate Authority
C. DigiCert Certificate Authority
D. Verisign Certificate Authority
【单选题】
An administrator is adding an NFS datastore as shown in the Exhibit. What is the purpose of the Servers to be added list?___
A. It contains the IP addresses of the NFS Storage Server to provide multipathing capability.
B. It contains the IP addresses of the ESXi hosts that mount the datastore.
C. It contains the IP addresses used for
D. ynamic Discovery of targets.
【单选题】
An administrator reports that the System Event log data is only available for 24 hours when reviewing the Hardware Status tab. Which condition could be responsible for the loss of data?___
A. A Reset event log was executed.
B. The statistical collection level was set to a value of 1.
C. The boot disk of the host is corrupt.
D. Syslog has been configured at the vCenter Server level.
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
