【单选题】
原配属关系不变,根据总公司、铁路局命令由他局、段派至本局、段入住及临时加入支配(长交路轮乘)的机车是___。P46T221
查看试卷，进入试卷练习
微信扫一扫，开始刷题
相关试题
【单选题】
长期备用的机车解除备用要在___h内(寒冷地区,平均气温低于零下10°C时,为72h)达到出段状态。P48T229
【单选题】
内、电机车无动力托运时，按不同类型机车制动机无动力回送要求,切断制动阀与列车制动主管的通路,开放___塞门。P49T233、234
【单选题】
18牵引总重吨公里=___×实际走行公里。P53T251
【单选题】
在坐标图形的机车周转图上,横轴线表示___。P57T258
【单选题】
在坐标图形的机车周转图上用纵轴线表示___。P57T258
【单选题】
内燃机车___作用后,在未判明原因前,禁止立即打开曲轴箱检查孔盖进行检查。P61T278
A. 水温继电器
B. 差示压力计
C. 油压继电器
【单选题】
检查电机内部时,开关或闸刀上须___。P61T278
【单选题】
列车进站停车时,必须施行制动后的___。P62T284
【单选题】
安全电压一般是指___及以下的电压。P66T305
【单选题】
机车在运行中，电机轴承异音或损坏应先___。P66T310
A. 断电对电机进行检查
B. 低速运行
C. 请求救援
【单选题】
所谓整备作业，就是对机车进行出发前的准备和供应，使其达到___规定的技术状态。P69T317
A. 《铁路技术管理规程》
B. 《铁路机车运用管理规则》
C. 《机车操作规则》
【单选题】
手触检查部件时，手背触及部件表面的持续时间为___S时相应的温度为70℃微热上下。P69T317
【单选题】
使用塞尺、直尺、卷尺及专用工具测量有关部件正常间隙、距离、行程等各限度尺寸的方法为___。P71T323
【单选题】
使用万用表测试电压、电阻、电流的数值,使用试灯测试电路中的断路、虚接等故障的方法为___。P71T323
【单选题】
机车进入挂车线后应注意距脱轨器、防护信号、车列前___m左右必须停车。P72T327
【单选题】
机车进入挂车线后应注意，确认脱轨器 、防护信号撤除后，显示连挂信号， 以不超过___的速度平稳连挂。 P72T327
A. 5km／h
B. 10km／h
C. 15km／h
【单选题】
检查和保养电器时要切断电源，机车辅修、小修时要用___的压缩空气吹扫电器，或用毛刷、棉布擦拭电器，使各电器保持清洁干燥。P77T350
A. 200～300kPa
B. 300～350kPa
C. 400～550kPa
【单选题】
一般电机轴承的加油量应占轴承空间的___为宜。P80T359。
【单选题】
保证电器的机械强度、导电、导磁性以及介质的绝缘性不受损害的最高温度称为___。
【单选题】
机车无动力回送时分配阀安全阀调整至___。P84T374
A. 150～200kPa
B. 200～350kPa
C. 350～450kPa
【单选题】
电器触头的磨损，主要是___。P85T379
【单选题】
电刷边缘及小部分有微弱的火花点或者非放电性红色小火花。换向器上没有黑痕,电刷上没有灼痕。这样的火花等级为___P86T387
【单选题】
检查带有压力的管子、细小管接头螺母、___以下螺母以及对光洁度要求较高或引有镀层的零件时，禁止锤击。P90T399
【单选题】
电力机车进行车顶作业时,机车必须停在安全区内,并办妥停电手续,挂好___线后方能进行。P90T399
【单选题】
当润滑油流动时,液体分子间的内摩擦阻力使液体流动性能下降,产生一种粘滞性,这种性能称为润滑油的___。P91T401
【单选题】
温度降低时，润滑油的粘度___。P91T401
【单选题】
牵引电动机的一端支在转向架构架上,另一端用抱轴承支在车轴上的悬挂方式和为___P94T415
【单选题】
一般的讲，机车最大运行速度不超过120km／h时，应采用___牵引电动机悬挂装置。P94T415
【单选题】
半悬挂的簧下质量通常为每轴___，而全悬挂的簧下质量为每轴2～3t。P95T416
【单选题】
以压缩空气为动力,通过控制传动装置使闸瓦压紧车轮踏面产生摩擦而形成的制动力称为___。P104T439
【单选题】
动力制动力的大小受到机车动力___功率的限制。P104T439
【单选题】
电磁制动应用在高速列车上，属于___。P104T439
【单选题】
造成滑行的原因之一是轨面有水、霜、冰、雪、油脂等物,降低了___。P106T445
【单选题】
造成滑行的原因之一是闸瓦压力过高，使制动力大于___。P106T445
A. 摩擦力
B. 粘着牵引力
C. 轮轨间的粘着力
【单选题】
列车紧急制动时，除机车制动机的自动撒砂外，当列车速度___时，应少量撒砂。P106T447
【单选题】
列车操纵示意图应根据担当区段的使用机型、___以及线路纵断面情况，按安全、合理的操纵方法绘制。P107T451
【单选题】
闸瓦产生的制动力等于闸瓦与车轮踏面之间的___。P109T459
【单选题】
有效制动时间内(到停车或缓解为止)列车所走行的距离称为___。P109T460
A. 列车制动距离
B. 有效制动距离
C. 空走距离
【单选题】
在列车施行常用制动后，若制动管再继续减压,制动缸的压力也不会再上升,这个使双方压力均衡时的制动管减压量,称为___。P109T462
A. 最大有效减压量
B. 最小减压量
C. 追加减压量
【单选题】
列车制动管定压为600kPa时，最大有效减压量为___。P109T462
A. 140kPa
B. 150kPa
C. 170kPa
推荐试题
【单选题】
What is an example of social engineering？___
A. gaining access to a computer by observing the user login credentials
B. gaining access to a build through an unguarded entrance
C. gaining access to a server by using a USB stick
D. gaining access to a server room by posing as local IT
【单选题】
Which type of Layer 2 attack enables the attacker to intercept traffic that is intended for one specific recipient？___
A. BPDU attack
B. DHCP starvation I LAB
C. MAC address spoofing
D. CAM table overflow
【单选题】
Which about nested policy maps in a zone-based firewall is true ?___
A. They are limited to two leve ls in a hierarchical policy
B. Parent policies are previously defined policies that are defined by using the service policy command
C. A child policy is a new policy that uses a pre-existing policy.
D. A child policy is a new that uses a pre-existing policy
【单选题】
In which configuration do you configure the ip ospf authentication key 1 command？___
A. routing process
B. interface
C. privileged
D. global
【单选题】
Which statement about command authorization and security contexts is true？___
A. If command authorization is configured， it must be enabled on all contexts.
B. The change to command invokes a new context session with the credentials of the currently
C. AAA settings are applied on a per-context basis
D. The enable. 15 user ang admins with chang to permission ha e dfferent command authorization levels pertontext
【单选题】
Which command do you enter to enable authentication for OSPF on an interface？___
A. router（config-if）#ip ospf message-digest-key 1 md5 CIS COPASS
B. router（config-if）#ip ospf authentication message-digest
C. router（config-if）#ip ospf authentication-key CISCOPASS
D. router（config-if）#area 0 authentication message-digest
【单选题】
What feature defines a campus area network？___
A. It has a single geographic location
B. It lacks external connectivity.
C. It has a limited number of segments.
D. It has limited or restricted Internet access
【单选题】
Which type of attack most commonly involves a direct attack on a network？___
A. :phishing
B. Trojan horse
C. denial of service
D. social engineering
【单选题】
What information does the key length provide in an encryption algorithm?___
A. the cipher block size
B. the hash bloc k size
C. the number of permutations
D. the packet size
【单选题】
How do you verify TaCACS+ connectivity to a device？___
A. You successfully log in to the device by using the local credentials
B. You connect via console port and receive the login prompt.
C. You connect to the device using SSH and receive the login prompt.
D. You successfully log in to the device by using ACS credentials
【单选题】
Which term best describes the concept of preventing the modification of data in transit and in storage？___
A. availability
B. confidentially
C. fidelity
D. integrity
【单选题】
Which loS command is used to define the authentication key for ntp？___
A. switch（config ）#ntp authentication-key 1 mds Clcs
B. switch（config ）#ntp authenticate
C. switch（config）#ntp trusted-key 1
D. switch（config）#ntp source 192.168.0.1
【单选题】
What is true about the cisco lOS Resilient Configuration feature ?___
A. The feature can be disabled through a remote session
B. There is additional space required to secure the primary cisco lOS image file.
C. The feature automatically detects image or configuration version mismatch.
D. Remote storage is used for securing files
【单选题】
When is the default deny all policy an exception in zone-based firewalls？___
A. when traffic terminates on the router via the self zone
B. when traffic traverses two interfaces in different zones
C. when traffic traverses two interfaces in the same zone
D. when traffic sources from the router via the self zone
【单选题】
.If an access port is assigned as an isolated port in a PVLAN， which network ports can it communicate with？___
A. promiscuous ports in the same PLVAN
B. isolated ports in the same PVLAN
C. all ports in the same PAVLAN at ILAR
D. all ports in the adjacent PVLAN
【单选题】
Which IPSEC mode is used to encypt traffic directly between a client and a server VPN endpoint？___
A. quick mode
B. transport mode
C. aggressive mode
D. tunnel mode
【单选题】
Which command do you enter to verify that a vpn connection is established between two endpoints and that the connection is passing traffic？ ___
A. Firewall#sh crypto session
B. Firewall#debug crypto isakmp
C. Firewall#tsh crypto ipsec sa
D. Firewall#sh crypto isakmp sa
【单选题】
which type of Pvlan port allows communication from all port types？___
A. isolated
B. in -line
C. community
D. promiscuous
【单选题】
Which command do you enter to configure your firewall to conceal internal addresses？___
A. no ip directed-broadcast
B. no ip logging facility
C. no proxy-arp
D. no ip inspect audit-trial
E. no ip inspect
F. route
【单选题】
Which feature defines a campus area network？ ___
A. It has a limited number of segments.
B. It has limited or restricted Internet access
C. It lacks ex1ternal connectivity.
D. It has a single geographic location
【单选题】
What technology can you use to provide data confidentiality data integrity and data origin authentication on your network？___
A. IPSec
B. Certificate Authority
C. IKE
D. Data
E. ncryption Standards
【单选题】
which standard is a hybrid protocol that uses oakley and skerne ke y exchanges is an ISAKMP framework？___
【单选题】
What is the actual los privilege level of User Exec mode？___
【单选题】
What is the effect of the asa command crypto isakmp nat-traversal？___
A. It opens port 500 only on the out side interface
B. It opens port 500 only on the inside interface
C. It opens port 4500 on all interfaces that are IPSec enabled
D. It opens port 4500 only on the out side interfac
【单选题】
Which Fire POWER preproce ssor engine is used to prevent SYN attacks？___
A. Inline normalization
B. IP Defragmentation
C. Ports can
D. etection
【单选题】
Which NAT type allows objects or groups to reference an IP address ？___
A. identity NAt
B. static NAT
C. dynamic
D. dynamic NAT
【单选题】
Which Auto NAT policies are processed first？___
A. Dynamic NAT with longest prefix
B. Dynamic NAT with shortest prefix
C. static NAT with longest prefix
D. static NAT with shortest prefix
【单选题】
Which feature allows a dynamic Pat pool to se lect the next address in the pat pool instead of the next port of an existing address？___
A. next IP
B. round robin
C. dynamic rotation
D. NAT address rotation
【单选题】
Which IPS detection method can you use to detect attacks that are based on the attackers IP address？___
A. anomally-based
B. policy-based
C. signature-based
D. reputation-based
【单选题】
Which type of encryption technology has the broadest platform support？___
A. software
B. middleware
C. file-level
D. hardware
【单选题】
Which type of address translation supports the initiation of comm unications bidirectionally ？___
A. multi-session PAT
B. dynamic NAT
C. dynamic PAT
D. static NAT
【单选题】
Which label is given to a person who uses existing computer scripts to hack into computers while lacking the expertise to write the own？___
A. script kiddy
B. white hat hacker
C. hacktivist
D. phreaker
【单选题】
What is the primary purpose of a defined rule in an IPS？___
A. to configure an event action that takes place when a signature is triggered
B. to define a set of actions that occur when a specific user logs in to the system
C. to configure an event action that is pre-defined by the system administrator
D. to detect internal attacks
【单选题】
Which option is the default valuce for the Diffie- Hell man group when configuring a site-to-site VPn on an asa device ？___
A. Group 1
B. Group 2
C. Group 5
D. Group 7
【单选题】
Which feature filters CoPP packets?___
A. access control lists
B. class maps
C. policy maps
D. route maps
【单选题】
Which command is used in global configuration mode to enable AAA？___
A. configure-model aaa
B. configure aaa-modelA
C. aaa new-model
D. aaa
E. XEC
【单选题】
Which statement about the given configuration is true？___
A. The single-connection command causes the device to establish one connection for all TACACS
B. The single-connection command causes the device to process one TacAcs request and then move to the next server
C. The timeout com mand causes the device to move to the next server after 20 seconds of TACACS inactive
【多选题】
What are two well-known security terms？___
A. phishing//网络钓鱼
B. ransomware //勒索软件
C. BPDU guard
D. LACP
E. hair-pinning
【多选题】
Which two commands must you enter to securely archive the primary bootset of a device___
A. router（config ）#secure boot-config
B. router（config）#auto secure
C. router（config）#secure boot-image
D. router（config）#service passw ord-encryption
【多选题】
Which two functions can SIEM provide ？___
A. correlation between logs and events from multiple systems
B. event aggregation that allows for reduced log storage requirements
C. proactive malware analysis to block malicious traffic
D. dual-factor authentication
E. centralized firewall management
