相关试题
【多选题】
在有限空间作业场所，应配备___、绳缆等安全和抢救器具以及其他必要的器具和设备。
A. 防毒面罩；
B. 呼吸器具；
C. 通信设备；
D. 梯子
【多选题】
机动车装运超长、超高或重大物件时应遵守的规定有___。
A. 物件中轴线与车厢中轴线应垂直；
B. 易滚动的物件顺其滚动方向应掩牢并捆绑牢同；
C. 用超长架装载超长物件时，在其尾部应设警告标志；
D. 押运人员应加强途中检查，捆绑松动应及时加固
【多选题】
水上运输前，应根据___等制定合理的运输方案。
A. 水运路线；
B. 船舶状况；
C. 装卸条件；
D. 人员数量
【多选题】
水上运输时，入舱的物件应放置平稳，___的物件应绑扎牢固。
A. 易滚；
B. 易滑；
C. 易漏；
D. 易倒
【多选题】
水上运输，用船舶接送作业人员应遵守的规定有___。
A. 禁止超载超员；
B. 船上应配备合格齐备的救生设备；
C. 乘船人员应正确穿戴救生衣，掌握必要的安全常识，会熟练使用救生设备；
D. 船上禁止搭载和存放易燃易爆物品
【多选题】
___车厢内禁止载人。
A. 货运汽车挂车；
B. 起重车；
C. 平板车；
D. 自动倾卸车
【多选题】
下列对起重机操作人员描述正确的是___。
A. 起重机械操作人员应持证上岗；
B. 非操作人员禁止进入操作室；
C. 操作人员应按规定的起重性能作业，禁止超载；
D. 当信号不清或错误时，操作人员可拒绝执行
【多选题】
起重吊装作业，起重指挥信号应___。
A. 简明；
B. 统一；
C. 畅通；
D. 准确
【多选题】
下列情况属于禁止动火作业的是___。
A. 压力容器或管道未泄压前；
B. 存放易燃易爆物品的容器未清洗干净前；
C. 风力达三级以上的露天作业；
D. 喷漆现场
【多选题】
夏季、雨汛期施工，雨季前应做好___等应急处置方案。现场排水系统应整修畅通，必要时应筑防汛堤。
A. 防风；
B. 防雨；
C. 防洪；
D. 防雷
【多选题】
起重机械吊装作业，吊件吊起100mm后应暂停，检查___，确认无误后方可继续起吊。
A. 起重系统的稳定性；
B. 制动器的可靠；
C. 物件的平稳性；
D. 绑扎的牢固性
【多选题】
使用卷扬机作业前应进行检查和试车，确认卷扬机设置稳固，___、离合器、保险棘轮、索具等合格后，方可使用。
A. 防护设施；
B. 电气绝缘；
C. 制动装置；
D. 导向滑轮
【多选题】
起重设备的吊索具和其他起重工具应按出厂___的规定使用，不准超负荷使用。
A. 宣传材料；
B. 包装箱标识；
C. 说明书；
D. 铭牌
【多选题】
钢丝绳（套）有下列情况之一者，应报废或截除___。
A. 绳股挤出、断裂；
B. 钢丝绳未上油保养；
C. 钢丝绳受化学介质的腐蚀外表出现颜色变化；
D. 钢丝绳的弹性显著降低，不易弯曲，单丝易折断
【多选题】
合成纤维吊装带使用前应对吊带进行试验和检查，下列选项正确的是___。
A. 所需标识已经丢失或不可辨识，应立即停止使用；
B. 吊装不得拖拉、打结使用；
C. 可以长时间悬吊货物；
D. 损坏严重者应做报废处理
【多选题】
起重滑车出现下述情况之一时应报废___。
A. 裂纹；
B. 轮槽径向磨损量达钢丝绳名义直径的25%；
C. 轮槽壁厚磨损量达基本尺寸的10%；
D. 轮槽不均匀磨损量达3mm
【多选题】
电动工器具使用前应检查的事项有___
A. 外壳、手柄无裂缝、无破损；
B. 保护接地线或接零线连接正确、牢固；
C. 机械防护装置完好；
D. 是否有检测标识
【多选题】
安全工器具包括防止触电、灼伤、坠落、淹溺等事故或职业危害，保障作业人员人身安全的___和标志牌等专用工具和器具的管理，应符合《国家电网公司安全工器具管理规定》。
A. 绝缘安全工器具；
B. 登高工器具；
C. 安全围栏（网）；
D. 个体防护装备
【多选题】
安全工器具不得接触___，不得移作他用。
A. 高温；
B. 明火；
C. 化学腐蚀物；
D. 尖锐物体
【多选题】
土石方施工时，挖掘施工区域应设措施有___。
A. 围栏；
B. 减速带；
C. 安全标志牌；
D. 夜间应挂警示灯
【多选题】
施工区域临时排水选用井点降水时应符合的规定有___。
A. 应制定井点降水施工方案；
B. 已成孔尚未下井点管前，井孔应用盖板封严；
C. 有车辆或施工机械通过区域，应对敷设的井点防护、加固；
D. 降水完成时，应及时将井填实
【多选题】
土石方施工采用挖掘机开挖时应遵守的规定有___。
A. 应避让作业点周围的障碍物及架空线；
B. 禁止人员进入挖斗内，禁止在伸臂及挖斗下面通过或逗留；
C. 暂停作业时，应将挖掘机熄火；
D. 挖掘机作业时，在同一基坑内不应有人员同时作业
【多选题】
下列对爆破施工描述正确的是___。
A. 爆破施工单位应按规定取得相应资质；
B. 作业人员应取得相应资格；
C. 爆破材料应自行妥善保管；
D. 爆破器材均应符合国家标准
【多选题】
搭设脚手架，脚手架钢管的选材应满足的要求有___。
A. 脚手架钢管宜采用φ48×3.5mm的钢管；
B. 脚手架钢管宜采用φ48.3×3.5mm的钢管；
C. 横向水平杆最大长度不超过2.2m；
D. 其他杆最大长度不超过6.5m
【多选题】
搭设脚手架，木脚手板的选材应满足的要求有___。
A. 木脚手板应用50mm厚的杉木或松木板制作；
B. 宽度以200～300mm为宜；
C. 长度以不超过6m为宜；
D. 距板的两端80mm处应用镀锌铁丝箍绕2～3圈或用铁皮钉牢
【多选题】
搭设脚手架，脚手板的铺设应遵守的规定有___。
A. 作业层端部脚手板探头长度应取150mm，其板两端均应与支撑杆可靠固定；
B. 脚手板与墙面的间距不应大于150mm；
C. 脚手板与墙面的间距不应大于200mm；
D. 对接处应设两根横向水平杆，两根横向水平杆的间距不得大于300mm
【多选题】
混凝土施工，拆模作业应按___的原则逐一拆除。
A. 后支先拆、先支后拆；
B. 先支先拆、后支后拆；
C. 先拆侧模、后拆底模；
D. 先拆非承重部分、后拆承重部分
【多选题】
钢筋工程中，下列有关钢筋安装描述正确的是___。
A. 不得站在钢箍上绑扎柱钢筋；
B. 起吊预制钢筋骨架时，下方不得站人，待骨架吊至离就位点1m以内时方可靠近，就位并支撑稳固后方可摘钩；
C. 脚手架上可放置工具、箍筋；
D. 登高时应将工具随身携带
【多选题】
混凝土施工，下列有关泵送混凝土描述正确的是___。
A. 支腿应支承在水平坚实的地面；
B. 泵启动时，人员禁止进入末端软管可能摇摆触及的危险区域；
C. 建筑物边缘作业时，操作人员应站在安全位置，使用辅助工具引导末端软管，禁止站在建筑物边缘手握末端软管作业；
D. 泵输送管线及臂架应与带电线路保持一定的安全距离
【多选题】
混凝土施工，下列有关混凝土浇捣描述正确的是___。
A. 基坑口应搭设卸料平台；
B. 卸料时基坑内不得有人；
C. 振捣作业人员应穿好绝缘靴、戴好绝缘手套；
D. 浇筑中应随时检查模板、脚手架的牢固情况
【多选题】
混凝土养护采用暖棚法时，应遵守的规定有___。
A. 暖棚应经设计并绑扎牢固
B. 暖棚应根据现场情况随意搭设；
C. 保温材料应具有阻燃特性
D. 施工中应经常检查并备有必要的消防器材
【多选题】
索道架设应按___因素精确计算索道架设弛度。
A. 索道设计运输能力；
B. 选用的承力索规格；
C. 支撑点高度和高差；
D. 跨越物高度和索道档距
【多选题】
山地铁塔地面组装时应遵守___规定。
A. 塔材顺斜坡堆放；
B. 选料应由下往上搬运，不得强行拽拉；
C. 山坡上的塔片垫物应稳固，且应有防止 构件滑动的措施；
D. 组装管形构件时，构件间未连接前应采取防止滚动的措施
【多选题】
塔上组装，下列规定对的是___。
A. 塔片就位时应先高侧后低侧；
B. 多人组装同一塔段（片）时，应由一人负责指挥；
C. 高处作业人员应站在塔身外侧；
D. 需要地面人员协助操作时，应经现场指挥人下达操作指令
【多选题】
整体组立杆塔，___应在同一垂直面上，不得偏移。
A. 总牵引地锚出土点；
B. 制动系统中心；
C. 抱杆顶点；
D. 杆塔中心
【多选题】
倒落式人字抱杆整体组立杆塔，关于抱杆支立做法对的是___。
A. 支立在松软土质处时，其根部应有防沉 措施；
B. 支立在松软土质处时，其根部应有防滑措施；
C. 支立在坚硬或冰雪冻结的地面上时，其根部应有防滑措施；
D. 支立在坚硬或冰雪冻结的地面上时，其根部应有防沉措施
【多选题】
直升机组塔应遵守___规定。
A. 应由有经验的人员在起降区域担任现场指挥；
B. 作业期间，地面作业人员应做好防静电措施；
C. 就位塔段安装固定后，直升机应加速上升；
D. 吊件对接就位过程中，对接面作业人员应采取安全防护措施
【多选题】
杆塔拆除应该根据现场地形、交跨情况确定拆塔方案，并应遵守___规定。
A. 分解拆除铁塔时，应按照组塔的逆顺序操作；
B. 先将待拆构件受力后，方准拆除连接螺检；
C. 整体倒塔时明确倒杆方向；
D. 先将原永久拉线解开
【多选题】
钢管跨越架所使用的钢管，如出现___等情况不得使用。
A. 弯曲严重
B. 磕瘪变形
C. 表面有锈迹
D. 裂纹或脱焊
【多选题】
使用导线、地线连接网套时应遵守___规定。
A. 网套应与所夹持的导线、地线规格相匹配；
B. 网套夹持导线、地线的长度不得少于导线、地线直径的20倍；
C. 网套末端应用铁丝绑扎，绑扎不得少于15圈；
D. 发现有断丝者不得使用
推荐试题
【多选题】
What are two ways to identify TCP/IP stack information? (Choose two.)___
A. Using the vSphere Web Client
B. Using esxcli network ip netstack
C. Using esxcfg-netstack
D. Using the vSphere Client
【多选题】
Which two actions are required when enabling vFlash Read Cache for a virtual machine's virtual disk? (Choose two.)___
A. A value in the Virtual Flash Read Cache text box must be entered.
B. A Flash Resource Pool for Cache size reservation must be entered.
C. The Device backing and the block size must be configured.
D. The
E. nable virtual flash host swap cache check box must be selected.
【多选题】
What two IT infrastructure components are virtualized by vSphere Essentials? (Choose two.)___
A. Networks
B. Applications
C. Storage
D. Management
【多选题】
When attempting to access a virtual machine, an administrator is unable to login using the vSphere credentials. What two options are probable causes of the authentication failure? (Choose two.)___
A. The vSphere credentials have not been granted permissions.
B. The vSphere credentials are granted read-only permissions.
C. The vSphere credentials are granted no-access permissions.
D. The vSphere credentials are not a member of the local administrator group.
【多选题】
An administrator is performing a scripted installation of ESXi 6.x. In which three locations does the script need to be? (Choose three.)___
A. PXE Server
B. HTTPS
C. FTP
D. NFS
E. VVOLs Datastore
【多选题】
In order for a company to meet regulatory requirements, all ESXi 6.x Hosts must be configured to direct logs to a syslog server. What are two ways ESXi hosts can configured for this action? (Choose two)___
A. Use the esxcli system syslog command.
B. Edit them in the ESXi host Advanced System Settings.
C. From the Syslog collector user interface of the Web Client.
D. Syslog logging is not available for
E. SXi Hosts.
【多选题】
Which three actions can be executed when an alarm is triggered? (Choose three.)___
A. Send an email.
B. Send an SNMP trap.
C. Run a script or command.
D. Run an Orchestrator workflow.
E. Send a trigger to syslog.
【多选题】
An administrator is attempting to power on a virtual machine, but is unable to do so. Which two reasons are probable causes of the failure? (Choose two.)___
A. Storage access to the virtual machine swap file has been lost.
B. One of the virtual machine VMDK files is locked.
C. Virtual machine is running CentOS 7.0 64-bit.
D. Virtual machine has Hyper-Threading enabled.
【多选题】
An administrator has configured a host profile so that ESXi 6.x hosts will point to the corporate NTP server for time synchronization. The NTP server is located at 10.0.30.213, but time has not been synchronized properly across the ESXi hosts. The administrator reviews Host Profile settings as shown in the Exhibit. Which two steps are required to resolve the issue? (Choose two.)___
A. Correct the NTP server IP address.
B. Check the host for host profile compliance.
C. Remediate the host based on the updated host profile.
D. Change the NTP server to the FQDN as IP Addresses are not supported.
【多选题】
An administrator is attempting to migrate a large Hadoop virtual machine using vMotion. The administrator notices a delay when the machine is quiesced. The Hadoop virtual machine is processing many transactions a second to an in-memory database. Which two actions would help reduce the amount of time needed to perform a vMotion on this virtual machine? (Choose two.)___
A. Use multiple NICs for the vMotion vmkernel port.
B. Use a 10Gbps Network card for the vMotion vmkernel port.
C. Add an additional management network to help transmit the data quicker.
D. Disable Fault Tolerance before performing the vMotion.
【多选题】
An administrator is installing a new network card in an ESXi 6.x host that is part of a vSphere cluster. When the host is placed into maintenance mode, the vSphere Web Client displays the progress bar at 2% for over 30 minutes. Which two are likely reasons for this occurrence? (Choose two.)___
A. Maintenance mode is unable to migrate all virtual machines from the host.
B. There is a large number of virtual machines that must be migrated from the host.
C. VMware High Availability is in the process of reconfiguring the cluster.
D. Each virtual machine on the
E. SXi host must be reconfigured to recognize the new adapter.
【多选题】
Which two events happen when Distributed Resource Scheduler (DRS) is disabled? (Choose two.)___
A. The cluster's resource pool heirarchy and affinity rules are re-established when DRS is turned back on.
B. The cluster's resource pool hierarchy and affinity rules are not re-established when DRS is turned back on.
C. The cluster's resource pools are removed from the cluster.
D. The cluster's resource pools are removed from the cluster and assigned to the hosts.
【多选题】
Which two networking connection types can be configured on a virtual switch? (Choose two.)___
A. Virtual machine portgroups
B. VMkernel services (such as NFS, iSCSI, or vMotion) to the physical network
C. Web services over the Management Network
D. NFS and FCoE storage services
【多选题】
An administrator creates a DRS cluster of eight ESXi 6.x hosts. There are 10 virtual machines balanced across the hosts. An attempt to place the first host into maintenance mode fails. What are two reasons that the host failed to enter maintenance mode? (Choose two.)___
A. The DRS cluster Automation Level is set to Partially Automated mode.
B. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Should run on hosts in group.
C. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Must run on hosts in group.
D. One of the virtual machines on the
E. SXi Host entering maintenance mode is configured with an individual Automation Level set to Partially Automated.
【多选题】
When modifying a vApp, which two vSphere entities can be added? (Choose two.)___
A. A resource pool
B. A network pool
C. A vApp
D. A folder
【多选题】
From which two locations in the inventory hierarchy can you deploy a virtual machine using a template? (Choose two.)___
A. Directly from the template.
B. From a compute resource.
C. From an existing virtual machine.
D. From a Datastore.
【多选题】
A company has decided to implement Virtual SAN within their vSphere 6.x environment. The Virtual SAN cluster will be composed of three ESXi 6.x hosts that are on the Virtual SAN Ready Node list. Each ESXi host includes: <Two SAS Controllers that support Passthrough Mode> < Four Solid State Drives (SSDs) 1TB in size each> <20 SAS Magnetic Disks (MDs) 1TB in size each> <The SSDs and MDs are evenly split between the two SAS controllers>. The company will pilot a Virtual SAN cluster utilizing VMware best practices while maximizing storage capacity. The Virtual SAN cluster will use Manual Mode. Which two Disk Group configurations would meet the stated configuration requirements? (Choose two.)___
A. 4 disk groups with 1 SSD and 5 MDs each
B. 2 disk groups with 1 SSD and 7 MDs each
C. 2 disk groups with 2 SSDs and 7 MDs each
D. 2 disk groups with 1 SSD and 10 MDs each
【多选题】
A physical Windows 2008 R2 Server is converted to a virtual machine using VMware vCenter Converter. Upon completion of the conversion and subsequent power on operation, the virtual machine fails to boot and the message below is observed in the Console of the virtual machine: <STOP 0x0000007B INACCESSIBLE_BOOT_DEVICE>. Which two potential issues may be causing this boot failure? (Choose two.)___
A. An incorrect SCSI controller was selected during conversion.
B. Incompatible software drivers were migrated into the virtual machine from the source machine.
C. The vmdk file backing the virtual machine was thick provisioned.
D. A snapshot was taken immediately after the conversion completed.
【多选题】
An administrator is configuring the Failover Order option on a vSphere Distributed Switch. Which two options should be used with IP-hash load balancing? (Choose two.)___
A. Active Uplinks
B. Standby Uplinks
C. Unused Uplinks
D. Override Failover Order
【多选题】
An administrator is configuring the Maximum Transmission Unit value on a vSphere Distributed Switch. Which two options are typical values for ESXi networking? (Choose two.)___
A. 1492
B. 1500
C. 9000
D. 9089
【多选题】
Which two configurable options apply to both virtual machine CPU and memory allocation? (Choose two.)___
A. Reservation
B. Shares
C. Resource Pool
D. Reserve All
【多选题】
When attempting to power on a Virtual Machine you observe the following error: <Cannot open the disk '/vmfs/volumes/volume/vm/vm-000002.vmdk' or one of the snapshot disks it depends on.> Which three actions will be the best solutions to address this problem? (Choose three.)___
A. Verify that the virtual machine's disk files are present.
B. Investigate the host and virtual machine log files.
C. Verify the vmdk descriptor files and if required, recreate them.
D. Delete the disk file preventing the power on operation.
E. Migrate or register the virtual machine to a different host.
【多选题】
An administrator has been tasked with enabling High Availability ___ on a cluster in a vSphere 6.x environment with default settings. The cluster configures properly and there are no errors. The next day when powering on a virtual machine, an error is presented: <Not Enough Failover Resources>. Which three scenarios are likely causes of this error message? (Choose three.)(CDE)
A. The default VM Monitoring Sensitivity is set too high.
B. There are not enough datastore heartbeat datastores configured by default.
C. The default slot size in the cluster is set too high.
D. There are virtual machines with large CPU reservations.
E. A host is in maintenance mode for a replacement of a failed Hard Drive.
【多选题】
vMotion can be performed between which three physical boundaries? (Choose three.)___
A. Between two vCenter Server Systems
B. Between two vSphere Distributed Virtual Switches
C. Between two vCenter Server Datacenter objects
D. Between two VMware NSX Layer 4 segments
E. Between two NFS datastores
【多选题】
An administrator configures vSphere Replication for a virtual machine and enables multiple point in time (PIT) instances under the recovery settings in the Configure Replication wizard. Which two statements are correct for vSphere Replication with multiple point in time instances enabled? (Choose two.)___
A. vSphere Replication retains a number of snapshot instances of the virtual machine on the target site based on the retention policy that you specify.
B. vSphere Replication uses the virtual machine's snapshot instances to define the target site Point in Time instance based on the retention policy that you specify.
C. vSphere Replication does not support virtual machines with snapshots.
D. vSphere Replication supports virtual machines with snapshots.
【多选题】
An administrator is virtualizing a physical application server and adding it to an existing multi-tiered vApp. The application license is currently tied to the physical NIC's MAC address, so the administrator needs to ensure the license will function properly in the virtual machine. Which two actions can the administrator take to satisfy this task? (Choose two.)___
A. Set the MAC address for the vNIC in the guest operating system.
B. Install the physical server's NIC into the ESXi host.
C. Configure the MAC address for the vNIC using the vSphere Web Client.
D. Assign the physical server NIC's MAC address in the vSphere Distributed Switch.
【多选题】
Which two Fibre Channel zoning options are supported with vSphere 6.x? (Choose two.)___
A. Single-Initiator
B. Single-Initiator-Single-Target
C. Multiple-Initiators-Single-Target
D. Multiple-Initiators-Multiple-Targets
【多选题】
An administrator is attempting to remove an ESXi 6.x host from a vSphere Distributed Switch (vDS). When the administrator attempts to remove the host, the following error is observed: <The resource '16' is still in use.> What three steps are needed to successfully remove the host from the switch? (Choose three.)___
A. Select Manage Ports on the vDS for the host.
B. Locate all ports currently in use on the vDS for the host.
C. Migrate or delete any vmkernel or virtual machine adapters associated with the switch.
D. Remove all network cards from the switch before trying to remove the host.
E. Create a standard switch for everything to be automatically be migrated to.
【多选题】
Which two Virtual SAN related actions might start resynchronization of virtual machine objects? (Choose two.)___
A. Editing a virtual machine storage policy to increase the number of replicas.
B. Editing a virtual machine storage policy to reduce the number of replicas.
C. Editing a virtual machine storage policy to increase the number of disk stripes.
D. Editing a virtual machine storage policy to reduce the number of disk stripes.
【多选题】
An administrator is troubleshooting basic network connectivity issues. Which two scenarios are potential issues that this administrator might face? (Choose two.)___
A. The vSwitch is not attached to the correct physical network.
B. The portgroup is not configured to use correct VLAN.
C. Traffic shaping is configured incorrectly.
D. Jumbo frames is configured incorrectly.
【多选题】
Which three items should be validated prior to installing ESXi 6.x? (Choose three.)___
A. Remote Storage has been disconnected.
B. Installation media is available.
C. Server hardware clock is set to UTC.
D. Storage has been partitioned with a VMFS volume.
E. Network cards have been setup to use Jumbo
F. rames.
【多选题】
An administrator is performing an interactive installation of ESXi 6.x. Which three options are available for installation? (Choose three.)___
A. DVD
B. USB
C. PXE
D. Scripted
E. Auto Deploy
【多选题】
After installation of a host in your test environment, you need to move it to production. The only major change that needs to be made is that the hostname of the server needs to change. What are two ways that an administrator can change the host name without editing configuration files on the host directly? (Choose two.)___
A. Login to the Direct Console User Interface and change it from here.
B. Edit the Default TCP/IP Configuration from the vSphere Web Client.
C. Use the Ruby vSphere Client to send a script to the ESXi host that updates the hostname.
D. Update the information in DNS and the
E. SXi host will automatically update with these changes.
【多选题】
An administrator has unsuccessfully attempted several times to install an Operating System inside a virtual machine. The administrator finds that the installation fails at random intervals. Which two actions can be taken to resolve this issue? (Choose two.)___
A. Verify the md5sum and if invalid, download the installation files again.
B. Attempt the installation an additional time.
C. Attempt to use a different installation media or installation method.
D. Create a new virtual machine and attempt the installation with the existing media.
【多选题】
VMware tools is failing to install on a Microsoft Windows virtual machine. What are two possible situations that would prevent the installation? (Choose two.)___
A. The VMware tools installation media is corrupt.
B. The incorrect Operating System was selected in the virtual machine options.
C. The software prerequisites have not been installed.
D. The prerequisite services have not been started.
【多选题】
As part of a multisite Single Sign-On (SSO) deployment what two steps are required to ensure that a change to one Single Sign-On instance is propagated to the other instances? (Choose two.)___
A. Schedule a Replication Task on the primary instance
B. Select the first instance during the installation of subsequent instances
C. During the installation of each instance choose Linked-Mode
D. Enable Synchronize to Active Directory on each instance
【多选题】
You need to add an object to an existing vApp using the vSphere Web Client. How is this accomplished?___
A. Create an Object Inside the vApp.
B. Add an Object to a vApp.
C. Add an Object to the
D. atastore the vApp is located in.
【多选题】
Which three steps must be taken to use vSphere Update Manager 6.x to upgrade an ESXi 5.5 host to vSphere 6.x? (Choose three.)___
A. Download an ESXi Image.
B. Configure the vSphere Update Manager Download Service.
C. Create a baseline and attach it to the ESXi Host.
D. Scan the vCenter Content Library for the
E. SXi Image.
【多选题】
Which two options would allow a database administrator, with no access to the vSphere infrastructure, to connect to a virtual machine? (Choose two.)___
A. Use the Virtual Machine Remote Console (VMRC).
B. Use Remote Desktop Protocol (RDP) to connect.
C. Ask the vSphere administrator to grant permission to access the console through vCenter Server.
D. Ask the vSphere administrator to grant permission to access with the Horizon View Direct Connect Client.
【多选题】
Which three are architecture components of vRealize Operations? (Choose three.)___
A. Identity Server
B. Administrative Server
C. Analytics Server
D. Database Server
E. Connection Broker
