刷题
导入试题
【单选题】
单动道岔组合共有四张类型图,其中弯股 反位. 在上直股在下,且是第一笔道岔的图号为 ___。
A. 1/DD
B. 2/DD
C. 3/DD
D. 4/DD
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
6502电气集中5、6线上串有下列三组继电器接点正确的是 ___。
A. QJJ、XJJ、DGJ
B. QJJ、CJ、DGJ
C. QJJ、CJ、FDGJ
D. QJ、CJ、DGJ
【单选题】
列车开始继电器LKJ自闭电路中并有 ___继电器接点。
A. 1个
B. 2个
C. 3个
D. 4个
【单选题】
信号检查继电器XJJ利用8线上串接KJ后接点和ZJ后接点来实现 ___。
A. 本咽喉没有建立敌对进路
B. 另一咽喉区没未建立敌对进路
C. 选排一致
D. 本咽喉没有建立进路
【单选题】
道岔启动电路中1DQJ的1-2线圈串入道岔动作电路的作用有 ___ 。
A. 1种
B. 2种
C. 3种
D. 4种
【单选题】
区段检查继电器QJJ、GJJ是挂在9线上,电路中的DBJ或FBJ的第2组接点是 ___用的。
A. 检查道岔位置
B. 参与道岔位置检查
C. 区分站场形状
D. 检查敌对进路
【单选题】
___时,进路上轨道区段的解锁顺序是从始终至终端方向逐段解锁。
A. 取消进路
B. 人工解锁
C. 正常解锁
D. 故障解锁
【单选题】
办理调车进路时,进路终端经过 ___ 的前接点向网路发送KZ或KF电源。
A. ZJ
B. ZCJ
C. XJJ
D. JXJ
【单选题】
6502电气集中利用CJ的 ___在正常解锁时,接通解锁网络使下一区段的LJ得以正常动作。
A. 快动
B. 正常动作
C. 缓动
D. 落下
【单选题】
进站、出站、进路或通过信号机的灯光熄灭、显示不明或显示不正确时,均视为___信号。
A. 正常行进
B. 减速
C. 停车
D. 错误
【单选题】
四线制道岔在分线盘上X1 或X2. 与X3线端子测量电压,判断道岔表示电路故障,当测得交流为105V、直流为0V,可判断为___。
A. 室外二极管击穿造成短路
B. 室外断线
C. 室内断线
D. 电容短路
【单选题】
信号机点亮红灯时___。
A. LXJ↓、DXJ↓、DJ↑
B. LXJ↑、DXJ↑、DJ↓
C. LXJ↑、ZXJ↑、2LQJ↓、DJ↑
D. LXJ↓、DXJ↑、DJ↑
【单选题】
6502电气集中选岔电路中,始端的___吸起与方向电源配合使LKJ或FKJ励磁并自闭。
A. JXJ
B. ZJ
C. AJ
D. KJ
【单选题】
6502电气集中选岔电路中,终端JXJ吸起与方向电源配合,使___励磁并自闭。
A. JXJ
B. ZJ
C. AJ
D. KJ
【单选题】
在MΩ表“线路L”端的外围,有一个铜质圆环,称为___ 。
A. 保护环
B. 接地环
C. 防护环
D. 安全环
【单选题】
微型计算机的微处理器包括___。
A. CPU和存储器
B. 运算器和累加器
C. CPU和控制器
D. 运算器和控制器
【单选题】
微型计算机的性能主要由微处理器的___决定。
A. 质量
B. 控制器
C. CPU
D. 价格性能比
【单选题】
一般用微处理器的___进行分类。
A. 字长
B. 规格
C. 性能
D. 价格
【单选题】
计算机之所以能实现自动连续运算,是由于采用了___原理。
A. 布尔逻辑
B. 存储程序
C. 数字电路
D. 集成电路
【单选题】
用万用表判断三极管的三个电极,任意测两极间的电阻,若有一个极与另外两极间的阻值在一个方向同时为低阻值,交换一下表笔,又同时为高阻值,则说明这个极是 ___ 。
A. 基极
B. 发射极
C. 集电极
D. 无法确定
【单选题】
两个稳压值不同的稳压二极管用不同的方式串联起来,可组成的稳压值有___。
A. 2种
B. 3种
C. 4种
D. 5种
【单选题】
将一只稳压二极管和一只普通二极管串联后,可得到的稳压值有___。
A. 2种
B. 3种
C. 4种
D. 5种
【单选题】
计算机中信息存储的最小单位是___ 。
A. 位
B. 字长
C. 字
D. 字节
【单选题】
如果被测电阻值超出所选择量程的最大值,万用表将显示___,这时应选择更高的量程。
A. “1”
B. “000”
C. “-”
D. 无显示
【单选题】
6502电气集中ZQJ不能励磁的故障现象 ___。
A. 办理取消进路手续时,总取消表示灯不亮,信号可以取消。
B. 总取消和总人解按钮表示灯均不亮。
C. 办理取消进路手续时,总取消表示灯不亮,且信号不能取消。
D. 总取消和总人解按钮表示灯均亮。
【单选题】
6502电气集中ZRJ不能励磁的故障现象___ 。
A. 办理取消进路手续时,总取消表示灯不亮,信号可以取消。
B. 总取消和总人解按钮表示灯均不亮。
C. 办理取消进路手续时,总取消表示灯不亮,且信号不能取消。
D. 总取消和总人解按钮表示灯均亮。
【单选题】
6502电气集中控制台引来的各种电源线以及从组合架引来的接通道岔表示电源线,都先连到就近的K1段控制台零层4柱端子板上,其中___ 电源,考虑到电流较大,还需经过汇流排端子转接。
A. KZ、KF、JZ三种电源
B. KZ、KF、DZ三种电源
C. KZ、KF两种电源
D. KZ、KF、JF三种电源
【单选题】
6502电气集中组合架六列侧面端子的用途,原则上规定:除定型网络线以外,组合与组合之间的联系用 ___ 。
A. 01与02
B. 02与03
C. 03与04
D. 06
【单选题】
发射极放大器的输出电压和输入电压在相位上的关系是 ___ 。
A. 同相位
B. 相位差90°
C. 相位差180°
D. 不能确定
【单选题】
6502电气集中,执行组电路中, ___ 吸起,将XJJ接上第8线。
A. KJ
B. FKJ
C. JXJ
D. JYJ
【单选题】
6502电气集中,执行组电路中,第8线检查的基本联锁条件是 ___ 。
A. 道岔位置正确,进路空闲。
B. 道岔位置正确,敌对进路未建立。
C. 进路空闲,敌对进路未建立,信号正常。
D. 道岔位置正确,进路空闲,敌对进路未建立。
【单选题】
在控制台上区分7,8,9线故障时,可在控制台上增加办理引导进路锁闭操作,则可根据原来办理的进路,判断出故障所处位置,例如:若原来办理的是接车进路,办理引导锁闭后进路无白光带,说明 ___ 。
A. 9线的QJJ和GJJ故障
B. 7线的KJ故障
C. 8线的XJJ故障
D. 9线的GJJ故障
【单选题】
控制台零层一块定型配线的端子板,可供 ___ 使用,使用后的空余端子也不再另作它用。
A. 一组单动道岔
B. 一架信号机
C. 一组单动道岔和一架信号机
D. 一组单动道岔和一组双动道岔
【单选题】
控制台零层,定型配线中,一组双动道岔使用 ___ 端子板。
A. 1块
B. 2块
C. 3块
D. 4块
【单选题】
列车开始继电器电路中,___ 复原,断开LKJ励磁电路。
A. AJ
B. KJ
C. 方向继电器
D. FKJ
【单选题】
列车开始继电器电路中,信号开放后,___ 复原,断开LKJ的第一条自闭电路。
A. AJ
B. KJ
C. 方向继电器
D. FKJ
【单选题】
列车开始继电器电路中,当进路内方第一道岔区段解锁后,___ 复原,断开LKJ第二条自闭电路。
A. AJ
B. KJ
C. 方向继电器
D. FKJ
【单选题】
组合架零层配线中,每个组合架零层能安放 ___ 端子板。
A. 11块
B. 12块
C. 13块
D. 14块
【单选题】
组合架零层配线中,从组合架正面看,从左向右顺序编号,___ 为电源端子板。
A. 01~03
B. 04~06
C. 07~08
D. 09~013
【单选题】
组合架零层配线中,从组合架正面看,从左向右顺序编号,___ 为熔断器端子板。
A. 01~03
B. 04~06
C. 07~08
D. 09~013
【单选题】
组合架零层配线中,从组合架正面看,从左向右顺序编号,___ 为供条件电源用的18柱端子板。
A. 01~03
B. 04~06
C. 07~08
D. 09~013
推荐试题
【单选题】
What is the minimum Cisco lOS version that supports zone-based firewalls?___
A. 12.1T
B. 15.1
C. 15.0
D. 124
【单选题】
In which type of attack does an attacker overwrite an entry in the CAM table to divert traffic destined to a legitimate host?___
A. DHCP spoofing
B. ARP spoofing
C. CAM table overflow
D. MAC spoofing
【多选题】
Which two attack types can be prevented with the impleme ntation of a Cisco IPS solution?___
A. DDos
B. man-in-the-middle
C. worms
D. ARP spoofing
E. VLAN hopping
【多选题】
choose four___
A. DHCP snooping ——————————blocks DHCP messages
B. Dynamic ARP inspection——————verifies IP-to-MAC traffic on untrusted ports
C. IP sources guard ——————————provides layer 2 interface security with ports ACLs
D. Port security————————————mitigates MAC-address spoofing at the access interface
【多选题】
choose four___
A. Step1————————run the system setup wizard
B. Step2————————add an authentication realm
C. Step3————————configure identity management
D. Step4————————configure directory group
【多选题】
What are two advanced features of the Cisco AMp solution for endpoints ___
A. contemplation
B. foresight
C. sandboxing
D. reputation
E. reflection
【多选题】
Which two characteristics of RADIUS are true?___
A. It encrypts only the password between user and server.
B. It uses TCP ports 1812/1813
C. It uses UDP ports 1812/1813.
D. It uses UDP port 49
E. It uses TCP port 49
【多选题】
What are two challenges of using a network-based IPS? ___
A. It is unable to determine whether a detected attack was successful
B. It requires additional storage and proce ssor capacity on syslog servers
C. As the network expands, it requires you to add more sensors.
D. It is unable to detect attacks across the entire network
E. It must support multiple operating systems.
【多选题】
What are two default be haviors of the traffic on a zone-based firewall?___
A. Traffic within the self -zone uses an im plicit deny all.
B. All traffic between zones is implicitly blocked
C. Communication is allowed between interfadAss that are members of the same zone
D. Communication is blocked between interfaces that are members of the same zone
E. The CBAC rules that are configured on router interfaces apply to zone interfaces
【多选题】
Which two advantages does the on-premise model for MDM deployment have over the cloud-based model?___
A. The on-premise model is easier and faster to de ploy than the cloud-based model
B. The on-premise model is more scalable than the cloud-based model
C. The on-premise model is generally less expensive than the cloud-based model
D. The on-premise model generally has less latency than the cloud- based model.
E. The on-premise model provides more control of the MDM solution than the cloud
【多选题】
Which two actions can an end usts take to manage a lost or stolen device in Cisco ISE? ___
A. Activate Cisco ISE End point Protection Services to quarantine the device.
B. Add the mac address of the device to a list of blacklisted devices
C. Force the device to be locked with a PIN
D. Request revocation of the digital certificate of the device.
E. Reinstate a device that the user previously marked as lost or stolen
【多选题】
Which two problems can arise when a proxy firewall serves as the gateway between networks?___
A. It can prevent content caching
B. It can limit application support
C. It is unable to prevent direct connections to other networks
D. It can cause reduced throughput.
E. It is unable to provide antivirus protection
【多选题】
When using the Adaptive Security Device Manager(ASDM), which two methods are available to add a new root certificate?___
A. Use sCep
B. Install from SFTP server
C. Install from a file
D. Use Https
E. Use LDAP
【多选题】
Which two are considered basic security principles?___
A. Accountability
B. Redundancy
C. High Availabilit
D. Integrity
E. Confidentiality
【多选题】
Which two roles of the Cisco WSA are true?___
A. IPS
B. firewall
C. antispam
D. web proxy
E. URL filter
【单选题】
Which next-generation encryption algorithm supports four variants?___
A. SHA-2
B. SHA-1
C. MD5
D. HMAC
【单选题】
What aims to remove the abil ity to deny an action?___
A. Non-Repudiation
B. Accountability
C. Integrity
D. Deniability
【单选题】
Which statements about the native VLAN is true ?___
A. It is susceptible to VLAN hopping attacks.
B. It is the Cisco recommended VLAN for switch-management traffic
C. It is most secure when it is a ssigned to vLAn 1.
D. It is the cisco-recomme nded vlan for user traffic
【单选题】
There are two versions of IKE:IKEv1 and IKEv2. Both IKEv1 and IKEv2 protocols operate in phases IKEv1 operates in two phases. IKEv2 operates in how many phases?___
A. 2
B. 3
C. 4
D. 5
【单选题】
What does the dh group refer to?___
A. length of key for hashing C
B. length of key for encryption
C. tunnel lifetime key
D. length of key for key exchange
E. length of key for authentication
【单选题】
Which path do you follow to enable aaa through the SDM ?___
A. Configure Tasks > AAA
B. Configure > Addition Authentication > AAA
C. Configure > AAA
D. Configure > Additional Tasks > AAA
E. Configure Authentication > AAA
【单选题】
which technology cloud be used on top of an MPLS VPN to add confidentiality ?___
A. IPsec
B. 3DES
C. AES
D. SSL
【单选题】
Which term is most closely aligned with the basic purpose of a SIEM solution? ___
A. Non-Repudiation
B. Accountability
C. Causality
D. Repudiation
【单选题】
You have just deployed SNMPv3 in your environment, Your manager asks you to make sure that our SNMP agents can only talk to the SNMP Manager. What would you configure on your SNMI agents to satisfy this request?___
A. A SNMP View containing the SNMP managers
B. Routing Filter with the SNMP managers in it applied outbound
C. A standard ACL containing the SNMP managers applied to the SNMP configuration
D. A SNMP Group containing the SNMP managers
【单选题】
Which feature prevents loops by moving a nontrunking port into an errdisable state when a BPDU is received on that port?___
A. BPDU filte
B. DHCP snooping
C. BPDU guard
D. Port Fast
【单选题】
Which command enables port security to use sticky MAC addresses on a switch?___
A. switchport port-security violation restrict
B. switchport port-security mac-address sticky
C. switchport port-security violation protect
D. switchport port-security
【单选题】
When you edit an IPS subsignature, what is the effect on the parent signature and the family of subsignatures?___
A. The change applies to the parent signature and the entire family of subsignatures
B. The change applies to the parent signature and the subsignature that you edit
C. The change applies only to subsignatures that are numbered sequentially after the subsignature that you edit
D. Other signatures are unaffected, the change applies only to the subsignature that you dit
【单选题】
Which type of mechanism does Cisco FirePOWER de ploy to protect ag detected moving across other networks?___
A. antivirus scanning
B. policy-based
C. reputation-based
D. signature-based
【单选题】
What action must you take on the ise to blacklist a wired device?___
A. Locate the switch through which the device is connected and push an a cl restricting all access by the device
B. Issue a CoA request for the de vice's mac address to each access switch in the network
C. Revoke the device's certificate so it is unable to authenticate to the network
D. Add the device's MAc address to a list of black listed devices
【单选题】
Which type of firewall can perform deep packet inspection?___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
欢迎使用我爱刷题
×
微信搜索我爱刷题小程序
温馨提示
×
请在电脑上登陆“www.woaishuati.com”使用