【单选题】
Which term is most closely aligned with the basic purpose of a SIEM solution? ___
A. Non-Repudiation
B. Accountability
C. Causality
D. Repudiation
查看试卷，进入试卷练习
微信扫一扫，开始刷题
相关试题
【单选题】
You have just deployed SNMPv3 in your environment， Your manager asks you to make sure that our SNMP agents can only talk to the SNMP Manager. What would you configure on your SNMI agents to satisfy this request？___
A. A SNMP View containing the SNMP managers
B. Routing Filter with the SNMP managers in it applied outbound
C. A standard ACL containing the SNMP managers applied to the SNMP configuration
D. A SNMP Group containing the SNMP managers
【单选题】
Which feature prevents loops by moving a nontrunking port into an errdisable state when a BPDU is received on that port？___
A. BPDU filte
B. DHCP snooping
C. BPDU guard
D. Port Fast
【单选题】
Which command enables port security to use sticky MAC addresses on a switch？___
A. switchport port-security violation restrict
B. switchport port-security mac-address sticky
C. switchport port-security violation protect
D. switchport port-security
【单选题】
When you edit an IPS subsignature， what is the effect on the parent signature and the family of subsignatures？___
A. The change applies to the parent signature and the entire family of subsignatures
B. The change applies to the parent signature and the subsignature that you edit
C. The change applies only to subsignatures that are numbered sequentially after the subsignature that you edit
D. Other signatures are unaffected， the change applies only to the subsignature that you dit
【单选题】
Which type of mechanism does Cisco FirePOWER de ploy to protect ag detected moving across other networks？___
A. antivirus scanning
B. policy-based
C. reputation-based
D. signature-based
【单选题】
What action must you take on the ise to blacklist a wired device？___
A. Locate the switch through which the device is connected and push an a cl restricting all access by the device
B. Issue a CoA request for the de vice's mac address to each access switch in the network
C. Revoke the device's certificate so it is unable to authenticate to the network
D. Add the device's MAc address to a list of black listed devices
【单选题】
Which type of firewall can perform deep packet inspection？___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing？___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication？___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning？___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5， but does not use encryption？___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist， using security intelligence to block illicit network activity. However， the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites？___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat（ins，any）dynamic interface】Which ty pe of NaT is configured on a Cisco ASA？___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network？___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration？___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS？___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security？___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true？ ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication，authorization，and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10？___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center？___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true？___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed？___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1．三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
5．熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6．热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7．交流接触器的作用是可以___接通和断开负载。
【单选题】
8．三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9．三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11．熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12．对于电阻性负载，熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13．对于电动机负载，熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3．5
【单选题】
14．使用快速熔断器时，一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16．短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
推荐试题
【单选题】
(71841)JL1型连接器恒定湿热试验48 h后，绝缘电阻不应小于( )。[211110202](1.0分)___
A. 0.2 M
B. 2 M
C. 20 M
D. 200 M
【单选题】
(71842)JL1型连接器湿热试验后，耐压试验电压为50 Hz，( )，耐压1 min。[212110202](1.0分)___
A. 1 000 V
B. 1 500 V
C. 2 000 V
D. 2 500 V
【单选题】
(71843)JL2型电力连接器耐压试验，常态下试验电压为50 Hz，( )，耐压1 min。[213110202](1.0分)___
A. 1 000 V
B. 1 500 V
C. 2 000 V
D. 2 500 V
【单选题】
(71844)使用直读式绝缘检测表，检测客车绝缘是否接地或绝缘是否合格，应将转换开关旋至( )。[322110221](1.0分)___
A. 检测挡
B. R×1 k 挡
C. R×10 k 挡
D. 任意挡
【单选题】
(71845)直读式绝缘检测表的转换开关旋至“检测”挡时，绝缘电阻值应在( )刻度线读数。[322120221](1.0分)___
【单选题】
(71846)客车车体交流配线两线间及各线与大地间的绝缘电阻值，当相对湿度在80%以上时，应大于( )。[211110221(1.0分)___
A. 100 k
B. 300 k
C. 700 k
D. 1 M
【单选题】
(71847)客车车体交流配线两线间及各线与大地间的绝缘电阻值，当相对湿度为71%～80%时，应大于( )。[212110221](1.0分)___
A. 50 k
B. 250 k
C. 750 k
D. 1 M
【单选题】
(71848)客车播音配线两线间及各线与大地间的绝缘电阻值，当相对湿度在71%～80%时，应大于( )。[213110221](1.0分)___
A. 100 k
B. 300 k
C. 700 k
D. 1 M
【单选题】
(71849)客车播音配线两线间及各线与大地间的绝缘电阻值，当相对湿度在61%～70%时，应大于( )。[221110221](1.0分)___
A. 100 k
B. 300 k
C. 700 k
D. 1 M
【单选题】
(71850)客车播音配线两线间及各线与大地间的绝缘电阻值，当相对湿度在60%以下时，应大于( )。[222110221](1.0分)___
A. 100 k
B. 300 k
C. 700 k
D. 1 M
【单选题】
(71851)1FC5、1FC6系列无刷三相交流同步发电机采用( )励磁装置。[323110205](1.0分)___
A. 不可控相复励
B. 可控相复励
C. 谐波
D. 可控
【单选题】
(71852)采用单独供电的客车，荧光灯照明的平均照度应不低于( )。[321110215](1.0分)___
A. 80 lx
B. 100 lx
C. 120 lx
D. 150 lx
【单选题】
(71853)集中供电的硬座、软座、软卧、餐车，采用荧光灯照明时的平均照度应不低于( )。[323110215](1.0分)___
A. 80 lx
B. 100 lx
C. 120 lx
D. 150 lx
【单选题】
(71854)采用集中供电的硬卧车，荧光灯照明的平均照度应不低于( )。[322110215](1.0分)___
A. 80 lx
B. 100 lx
C. 120 lx
D. 150 lx
【单选题】
(71855)TFX1防滑器系统的速度传感器与轴头齿轮之间的间隙为( )。[333120202](1.0分)___
A. 1.0 mm±0.2 mm
B. 1.0 mm±0.5 mm
C. 1.5 mm±0.2 mm
D. 1.5 mm±0.5 mm
【单选题】
(71856)25K型空调客车的空调控制柜(KLC40C-1T1)中12号线是( )控制线。[321110228](1.0分)___
【单选题】
(71857)25K型空调客车的空调控制柜(KLC40C-1T1)中6号线是( )控制线。[321120228](1.0分)___
【单选题】
(71858)25K型空调客车的空调控制柜(KLC40C-1T1)中KA1～KA2，KA5～KA6是高灵敏、( )继电器。[321110206](1.0分)___
A. 高电压
B. 普通
C. 高内阻
D. 小电流
【单选题】
(71859)用1 000 V级绝缘表测量DC 600 V干线的线间和对地的绝缘电阻值应( )(相对湿度在60%～85%)。[321110220](1.0分)___
A. 2～2.3 M
B. ＞0.30 M
C. 0.38～2 M
D. ≥0.38 M
【单选题】
(71860)25K型空调客车的空调控制柜(KLC40C-1T1)是通过电流继电器FA6，FA7对两台( )进行过载保护的。[321110205](1.0分)___
A. 通风机
B. 压缩机
C. 冷凝机
D. 废排风机
【单选题】
(71861)变压器二次侧开路时，经过一次绕组内的电流称为( )。[321110206] (1.0分)___
A. 空载电流
B. 负载电流
C. 输入电流
D. 短路电流
【单选题】
(71862)当交流断电时，电池在应急控制系统的控制下向轴温报警装置、应急灯、( )等需应急工作的直流负载供电。[321110202](1.0分)___
A. 信息显示屏
B. 电茶炉
C. 尾灯插座
D. 客室照明
【单选题】
(71863)统型应急电源的三相380 V交流电源接到( )连接的三相降压变压器B2初级，三相降压变压器B2的次级接到整流模块U2。[321120206](1.0分)___
A. △/△
B. △/Y
C. Y/Y
D. Y/△
【单选题】
(71864)交流电机在空载运行时，功率因数( )。[312110206](1.0分)___
A. 高
B. 低
C. 先高后低
D. 先低后高
【单选题】
(71865)客车电气综合控制柜的主电路中接有DC 600 V( )(6～150 mA可调，共分六挡)，当漏电值超过设定值时，自动切断供电，同时漏电指示灯亮。[312110221](1.0分)___
A. 在线绝缘检测装置
B. 绝缘检测装置
C. 漏电报警装置
D. 轴温报警装置
【单选题】
(71866)25T型客车在正常供电时，空调、客室电热等负载由( )35 kV•A逆变器供电。[322110505](1.0分)___
【单选题】
(71867)25T型客车的逆变器箱主电路为( )电路，采用IGBT作为开关器件，具有开关频率高、驱动简单、损耗低的特点。[322110206](1.0分)___
A. 单相桥式大电流型
B. 单相桥式电压型
C. 三相桥式电压型
D. 三相桥式大电流型
【单选题】
(71868)25T型客车的逆变器，在输出额定电压、额定电流和规定的负载功率因数状态时，逆变器的效率应大于( )。[322120505](1.0分)___
A. 80％
B. 90%
C. 75％
D. 85％
【单选题】
(71869)25T型客车的逆变器应有一定的承受输入( )的能力。[322110213](1.0分)___
A. 电流突变
B. 电压突变
C. 功率突变
D. 功率因数突变
【单选题】
(71870)25K型空调客车的空调控制柜(KLC40C-1T1)中KT1，KT2的时间设定值为( )。[321120205](1.0分)___
A. 30 s和35 s
B. 60 s和70 s
C. 20 s和40 s
D. 3 min和5 min
【单选题】
(71871).25K型空调客车的空调控制柜(KLC40C-1T1)的客室电加热控制回路须经过( )中3Q，4Q的控制。[321110203](1.0分)___
A. 温度控制柜
B. 电源控制柜
C. 电茶炉控制箱
D. 照明控制柜
【单选题】
(71872)25T型客车的逆变器输出三相负载允许( )不平衡。[321110206](1.0分)___
A. 30％
B. 20%
C. 10％
D. 15％
【单选题】
(71873)25T型客车的逆变器在20 kW负载状态下稳定运行时，突加制冷压缩机负载(功率为4.5～5.5 kW)，逆变器( )。[211110505](1.0分)___
A. 必须重新启动
B. 必须停机，3～5 min再启动
C. 应能正常运行
D. 将会跳闸
【单选题】
(71874)25T型客车的充电器进行模拟过分相试验：充电器每工作( )，输入电源断电10 s，充电器应能正常工作，该项试验连续模拟10次。[212110205](1.0分)___
A. 10 min
B. 1 min
C. 5 min
D. 20 mi
【单选题】
(71875)25T型客车的充电器在额定输入状态下，突加、突减( )额定负载，充电器应能正常工作。[213110205](1.0分)___
A. 30％
B. 50%
C. 45％
D. 25％
【单选题】
(71876)MS730CP6C塞拉门是高速旅客列车使用的系列化外摆塞拉门，控制方式为( )。[221110211](1.0分)___
A. 气压控制
B. 电信号控制
C. 计算机控制
D. 液压控制
【单选题】
(71877)MS730CP6C塞拉门的车门系统具有( )功能。[212110211](1.0分)___
A. 防断电
B. 防挤压
C. 防过压
D. 防漏电
【单选题】
(71878)对全车性能试验的车辆应在车体两侧涂打( )的白色标记。[222110210](1.0分)___
A. 一条宽为50 mm
B. 一条宽为100 mm
C. 两条宽为50 mm
D. 两条宽为100 mm
【单选题】
(71879)电气装置与轨面距离运用限度规定不小于( )。[323110202](1.0分)___
A. 80 mm
B. 100 mm
C. 120 mm
D. 请输入内容
【单选题】
(71880)25T型客车的蓄电池组应有短路保护，各极对箱体间的绝缘电阻应不小于( )。[322110302](1.0分)___
A. 20 M
B. 10 M
C. 15 M
D. 50 M
