【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
查看试卷,进入试卷练习
微信扫一扫,开始刷题
相关试题
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
18.交流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
19.直流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
20.接触器的额定电压应不小于主电路的___。
A. 短路电压
B. 工作电压
C. 最大电压
D. 峰值电压
【单选题】
21.接触器的额定电流应不小于被控电路的___。
A. 额定电流
B. 负载电流
C. 最大电流
D. 峰值电流
【单选题】
22.对于___工作制的异步电动机,热继电器不能实现可靠的过载保护。
A. 轻载
B. 半载
C. 重复短时
D. 连续
【单选题】
23.对于△接法的异步电动机应选用___结构的热继电器。
【单选题】
24.对于工作环境恶劣、启动频繁的异步电动机,所用热继电器热元件的额定电流可选为电动机额定电流的___倍。
A. 0.95~1.05
B. O.85~0.95
C. 1.05~1.15
D. 1.15~1.50
推荐试题
【单选题】
注氮完毕后,应先( )液氮注入侧阀,再___管道侧阀门。
A. 关闭 关闭
B. 关闭 打开
C. 打开 关闭
D. 打开 打开
【单选题】
置换作业介质流速应控制在___m/s。
A. 1~3
B. 2~4
C. 3~5
D. 4~6
【单选题】
置换时,每个检测点应使用( )台检测仪分别进行___次检测。
A. 1 2
B. 2 1
C. 2 2
D. 1 1
【单选题】
不准在带有压力(液体压力或气体压力)或带电的设备上进行焊接、气割;在特殊情况下必须在带压和带电设备上进行焊接、气割时,应采取安全措施,并经___批准。
A. 主管生产的领导
B. 工作部门负责人
C. 总经理
D. 技术质量部负责人
【单选题】
电焊机一次线(搭铁线)长度应小于___m。
【单选题】
电焊机二次线(焊把线)长度应小于___m。
【单选题】
使用氧气、乙炔时,不得将瓶内气体全部用完,氧气瓶最少应留___Mpa。
A. 0.1
B. 0.2
C. 0.3
D. 0.4
【单选题】
使用氧气、乙炔时,乙炔瓶剩余压力应符合安全要求,当环境温度<0℃时,压力应不低于___MPa。
A. 0.01
B. 0.05
C. 0.1
D. 0.2
【单选题】
使用氧气、乙炔时,乙炔瓶剩余压力应符合安全要求,当环境温度为25℃~40℃时,应不低于___MPa。
A. 0.1
B. 0.2
C. 0.3
D. 0.4
【单选题】
在金属容器内进行焊接工作,容器外应设专人监护,监护人与焊工距离应保持___
A. 1m内
B. 1.2m内
C. 1.3m内
D. 在对方视力或听力范围内
【单选题】
在金属容器内进行焊接工作,容器内使用的防爆行灯,电压不准超过___。
A. 12V
B. 24V
C. 36V
D. 48V
【单选题】
不间断电源(UPS)进行拆卸作业前,应先断电,在相应隔离开关上悬挂禁止操作牌,并静置___分钟以上,待主机电容放电完成后方可进行
【单选题】
断开蓄电池与发电机连接时,应按先拆( )、再拆___的顺序进行。
A. 负极 正极
B. 正极 负极
C. 接地极 负极
D. 接地极 正极
【单选题】
恢复蓄电池与发电机连接时,应按先接( )、再接___的顺序进行。
A. 负极 正极
B. 正极 负极
C. 接地极 负极
D. 接地极 正极
【单选题】
中控系统维护作业前,应确认调度中心所辖所有站场、阀室的控制权限在___;
A. 中心站或值守站
B. 调度中心
C. 无人驻守站
D. 有人值守站
【单选题】
中控系统维护作业前,应备份___SCADA系统程序、报警数据、历史数据及相关参数记录。
A. 中心站或值守站
B. 调度中心
C. 无人驻守站
D. 有人值守站
【单选题】
中控系统维护作业前,调度中心值班人员和输气站场人员不得将控制权限切换至___。
A. 中心站或值守站
B. 调度中心
C. 无人驻守站
D. 有人值守站
【单选题】
站控系统维护作业前,应将站控SCADA系统权限切换至___。
A. 中心站或值守站
B. 调度中心
C. 异地
D. 本地
【单选题】
站控系统维护作业前,应将全站电动执行机构切换至就地___状态。
A. stop
B. local
C. remote
D. ok
【单选题】
站控系统维护作业中,调度中心值班人员和输气站场人员不得将控制权限切换至___。
A. 中心站或值守站
B. 调度中心
C. 异地
D. 本地站控
【单选题】
电动执行机构检修或维护作业前,应将执行机构打至就地___状态
A. stop
B. local
C. remote
D. ok
【单选题】
通信系统维护或检修作业前,应将SCADA控制系统权限切换至___。
A. 中心站或值守站
B. 调度中心
C. 异地
D. 本地
【单选题】
流量计算机检修或维护作业前,应将流量计___。
A. 在用状态
B. 直接退出运行
C. 退出运行并切换到备用支路
D. 断电
【单选题】
流量计算机和流量计重启作业前,___应记录设备累积量底数,以免重启后累计流量丢失。
A. 运行人员
B. 检修人员
C. 厂家
D. 技术人员
【单选题】
仪表检定应由有___操作,保证量值传递准确、可靠、统一。
A. 技术人员
B. 运行人员
C. 检定资质的人员
D. 检修人员
【单选题】
工作申请得到同意后,方可填写工作票。如需2个及以上专业配合完成的工作,应由___担任工作负责人,填写工作票,并经其他各方审核确认。
A. 主要工作方
B. 任意方
C. 工作部门负责人指定
D. 调度部门负责人指定
【单选题】
工作票应一式___份,填写应正确清楚,不得任意涂改。
【单选题】
两份工作票中的一份必须经常保存在工作地点,由()收执,另一份由___收执,按值、按时移交。
A. 工作负责人 工作许可人
B. 工作签发人 工作许可人
C. 工作负责人 工作监护人
D. 工作签发人 工作负责人
【单选题】
《三级工作票》由___签发。
A. 工作部门负责人或技术专工
B. 工作部门班组长或技术员
C. 工作部门技术专工
D. 工作部门负责人或技术专工或现场工作负责人
【单选题】
工作票签发应写明___字样,必要时应附加有关要求或补充安全措施,不允许只签名不签意见。
A. “允许”或“不允许”
B. “同意”或“不同意”
C. “通过”或“不通过”
D. “批准”或“不批准”
【单选题】
___负责确认工作票所列安全措施和风险辨识、控制措施是否正确完备。
A. 工作签发人
B. 工作监护人
C. 工作负责人
D. 工作许可人
【单选题】
___负责检查工作班成员精神状态是否良好,是否满足所从事工作的要求。
A. 工作签发人
B. 工作监护人
C. 工作许可人
D. 工作负责人
【单选题】
___工作前向工作班全体成员进行安全交底,并要求工作班成员严格执行工作票所列安全措施和风险控制措施。
A. 工作监护人
B. 工作签发人
C. 工作许可人
D. 工作负责人
【单选题】
___负责正确完成工作票所列安全措施的操作,并检查工作范围与运行设备是否有效隔离,设备设施是否有突然来气、来电等危险。
A. 工作监护人
B. 工作签发人
C. 工作许可人
D. 工作负责人
【单选题】
___负责对工作现场不定期监督检查,重点检查与运行有交叉的现场作业。发现违章作业应及时制止。
A. 工作负责人
B. 工作许可人
C. 工作监护人
D. 工作签发人
【单选题】
___负责发布输气设备设施停役(包括撤出备用)、复役(包括恢复备用)或投入运行指令。
A. 值班调度
B. 工作许可人
C. 工作负责人
D. 工作签发人
【单选题】
从事输气管道设备设施维(检、抢)修、施工等工作的相关方人员不得担任___
A. 工作负责人
B. 工作许可人
C. 工作监护人
D. 工作签发人
【单选题】
国家规定要求取得相应资格证书才能上岗作业的工作人员,必须经过___。
A. 公司内部培训
B. 相关专业培训并取得相应资格证书
C. 社会培训机构培训
D. 社会培训机构培训及该机构培训合格证书
【单选题】
___单位(包括管道企业自身)在输气管道现场从事交叉作业,必须书面明确交叉作业安全措施,并由管道企业对各方工作负责人进行安全交底,并要求各方安排专门监护人在现场履行对交叉作业的组织协调和监督监护职责。
A. 两个及以上
B. 三个及以上
C. 四个及以上
D. 五个及以上
【单选题】
凡停供气、回路切换等涉及调度部门管辖范围的设备设施上的工作均应向___申请并得到批准
A. 检修部门
B. 技术部门
C. 调度部门
D. 输气站场