【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
查看试卷,进入试卷练习
微信扫一扫,开始刷题
相关试题
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
18.交流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
19.直流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
20.接触器的额定电压应不小于主电路的___。
A. 短路电压
B. 工作电压
C. 最大电压
D. 峰值电压
【单选题】
21.接触器的额定电流应不小于被控电路的___。
A. 额定电流
B. 负载电流
C. 最大电流
D. 峰值电流
【单选题】
22.对于___工作制的异步电动机,热继电器不能实现可靠的过载保护。
A. 轻载
B. 半载
C. 重复短时
D. 连续
【单选题】
23.对于△接法的异步电动机应选用___结构的热继电器。
【单选题】
24.对于工作环境恶劣、启动频繁的异步电动机,所用热继电器热元件的额定电流可选为电动机额定电流的___倍。
A. 0.95~1.05
B. O.85~0.95
C. 1.05~1.15
D. 1.15~1.50
【单选题】
25.中间继电器的选用依据是控制电路的___、电流类型、所需触点的数量和容量等。
A. 短路电流
B. 电压等级
C. 阻抗大小
D. 绝缘等级
【单选题】
26中间继电器一般用于___中。
A. 网络电路
B. 无线电路
C. 主电路
D. 控制电路
推荐试题
【单选题】
正在切削的切削层表面称为( )。(1.0分)
A. 未加工表面
B. 待加工表面
C. 加工表面
D. 已加工表面
【单选题】
运行中受外力打击是造成集尘盒( )的主要原因。(1.0分)
【单选题】
带轮装在轴上后,要检查带轮的径向跳动量和( ),一般情况下用百分表检查。(1.0分)
A. 轴向跳动量
B. 径向偏摆
C. 同轴度
D. 垂直度
【单选题】
相同材料的弯曲半径越小,变形( )。
A. 越大
B. 越小
C. 不变
D. 可能大也可能小
【单选题】
负有事故主要责任的,承担损失费用的( )以上。
A. 80%
B. 50%
C. 30%
D. 20%
【单选题】
如要求轴与轴上零件的对中性和沿轴向相对移动的导向性都好,且能传递大的载荷时,应选用( )联接。(1.0分)
【单选题】
划线时当发现毛坯误差不大,但用找正方法不能补救时,可用( )方法来予以补救,使加工后的零件仍能符合要求。(1.0分)
A. 找正
B. 借料
C. 变换基准
D. 改图样尺寸
【单选题】
检查两带轮相互位置的正确性,中心距较大的场合,用( )。(1.0分)
A. 直尺测量
B. 拉线法
C. 角尺
D. 光照法
【单选题】
制动缸的是在进气一侧进入压力空气后,推动( )向前运动而产生推力的。(1.0分)
A. 密封圈
B. 活塞
C. 活塞杆
D. 弹簧
【单选题】
刀具材料的硬度越高,耐磨性( )(1.0分)
【单选题】
Z525型立钻主要用于( )。(1.0分)
【单选题】
为了促进企业的规范化发展,需要发挥企业文化的( )功能。
【单选题】
GK型三通阀具有( )充气减速缓解作用。(1.0分)
【单选题】
用标准麻花钻改制标准群钻时,其横刃应修磨为原来的( )。(1.0分)
A. 1/2~1/3
B. 1/3~1/4
C. 1/5~1/7
D. 1/4~1/5
【单选题】
为使钢获得高的韧性和足够的强度,一些重要零件要进行( )处理。(1.0分)
A. 退火
B. 正火
C. 调质
D. 低温回火
【单选题】
切削工作,当切削速度愈高时,刀具寿命( )(1.0分)
【单选题】
前刀面与( )之间的夹角称为前角。(1.0分)
A. 基面
B. 后刀面
C. 主截面
D. 切削平面
【单选题】
120型控制阀滑阀剩余厚度不足( )时更换。(1.0分)
A. 10 mm
B. 12 mm
C. 16 mm
D. 18 mm
【单选题】
带轮相互位置不准确会引起带张紧不均匀而过快磨损,当( )不大时,可用长直尺准确测量。(1.0分)
A. 张紧力
B. 摩擦力
C. 中心距
D. 都不是
【单选题】
已建立劳动关系,未同时订立书面劳动合同的,应当自用工之日起( )内订立书面劳动合同。(1.0分)
A. 10天
B. 20天
C. 一个月
D. 三个月
【单选题】
当过盈量及配合尺寸较小时,一般采用( )装配(1.0分)
A. 温湿法
B. 压入法
C. 爆炸法
D. 液压配套法
【单选题】
办事公道是指职业人员在进行职业活动时要做到( )。
A. 原则至上,不徇私情,举贤任能,不避亲疏
B. 奉献社会,襟怀坦荡,待人热情,勤俭持家
C. 支持真理,公私分明,公平公正 ,光明磊落
D. 牺牲自我,助人为乐,邻里和睦 ,正大光明
【单选题】
装配楔键时,要用涂色法检查( )与轴槽或毂槽的接触情况(1.0分)
A. 楔键、下表面
B. 楔键两侧表面
C. 楔键上表面
D. 楔键下表面
【单选题】
钻头( )为零时,靠近切削部分的棱边与孔壁的摩擦比较严重,容易发热和磨损。(1.0分)
A. 前角
B. 后角
C. 横刃斜角
D. 副后角
【单选题】
当轴承的旋转精度要求较高时,应采用( )的配合。(1.0分)
【单选题】
对于拆卸后还要重复使用的滚动轴承,拆卸时不能损坏轴承的( )(1.0分)
A. 内圈
B. 外圈
C. 滚动体
D. 配合表面
【单选题】
120型控制阀滑阀逆流孔为( )。(1.0分)
A. Φ1.0 mm
B. Φ0.8 mm
C. Φ0.5 mm
D. Φ0.2 mm
【单选题】
装配前做好一切技术准备,熟悉装配图、清点所有零件和使用( )等。(1.0分)
A. 夹具
B. 工具、量具
C. 油盒
D. 润滑油、润滑脂
【单选题】
淬火后,再进行高温回火的处理方法,称为( )。(1.0分)
【单选题】
120型控制阀的紧急活塞杆上紧急室充气限制孔为( )。(1.0分)
A. Ф0.5 mm
B. Ф0.6 mm
C. Ф0.8 mm
D. Ф1.0 mm
【单选题】
闸调器检修完成后,贮存期超过( )的,须经试验台试验合格后装车使用;(1.0分)
A. 1个月
B. 3个月
C. 3个月不足6个月
D. 6个月
【单选题】
齿轮传动中,为增加接触面积,改善啮合质量,在保留原齿轮传动副的情况下,采取( )措施。 (1.0分)
A. 刮削
B. 研磨
C. 锉削
D. 加载跑合
【单选题】
滚动轴承装配时,如过盈量较小,可采用( )方法压入轴承。(1.0分)
A. 套筒压人
B. 压力机压入
C. 利用温差
D. 直接敲入
【单选题】
120型控制阀滑阀缓解槽深不足( )时更换。(1.0分)
A. 1.6 mm
B. 1.8 mm
C. 2.0 mm
D. 2.2 mm
【单选题】
要求间歇运动,转动角度较大而且具有自锁性能,应采用( )。(1.0分)
A. 棘轮机构
B. 槽轮机构
C. 凸轮机构
D. 滑块机构
【单选题】
要做到遵纪守法,对每个职工来说,必须做到( )。(1.0分)
A. 有法可依
B. 反对“管“、“卡”、“压”
C. 反对自由主义
D. 努力学法,知法、守法、用法
【单选题】
JZ-7型空气制动机自动制动阀放风阀胶垫阀口压痕深度不得超过( )。(1.0分)
A. 0.5mm
B. 0.4mm
C. 0.6mm
D. 0.7mm
【单选题】
较重要锻铸件,为消除内应力和组织不均及晶粒粗大等采用( )处理。(1.0分)
A. 退火
B. 正火
C. 回火
D. 低温回火
【单选题】
JZ-7型空气制动机自动制动阀性能试验中,手柄移置紧急制动位均衡风缸压力减压( )。(1.0分)
A. 230~260 kPa
B. 240~260 kPa
C. 220~250 kPa
D. 220~270 kPa
【单选题】
120-1型控制阀滑阀缓解槽深不足( )时更换。(1.0分)
A. 1.6 mm
B. 1.8 mm
C. 2.0 mm
D. 2.2 mm