刷题
导入试题
【多选题】
下列属于防止线路爬行的措施有___?
A. 加强轨道的中间扣件的扣压力
B. 安装轨距杆或轨撑
C. 加强接头夹板的夹紧力
D. 在线路上进行涂油
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
ABC
解析
暂无解析
相关试题
【多选题】
关于圆曲线的最小长度,以下说法错误的是___
A. 不应小于10m
B. 不应小于15m
C. 不应大于10m
D. 不应大于15m
【多选题】
关于缓和曲线的最小长度,以下说法错误的是___
A. 50m
B. 40m
C. 30m
D. 20m
【多选题】
关于正线一般情况最小曲率半径,以下说法错误的是___
A. 400m
B. 350m
C. 300m
D. 250m
【多选题】
关于正线困难情况最小曲率半径,以下说法错误的是___
A. 200m
B. 250m
C. 300m
D. 350m
【多选题】
关于辅助线一般情况最小曲率半径,以下说法错误的是___
A. 500m
B. 400m
C. 300m
D. 200m
【多选题】
关于辅助线困难情况最小曲率半径,以下说法错误的是___
A. 150m
B. 200m
C. 300m
D. 350m
【多选题】
关于车场线一般情况最小曲率半径,以下说法错误的是___
A. 300m
B. 250m
C. 110m
D. 100m
【多选题】
关于车场线困难情况最小曲率半径,以下说法错误的是___
A. 50m
B. 80m
C. 120m
D. 150m
【多选题】
___不属于产生曲线钢轨不均匀磨耗的主要原因。
A. 曲线超高设置不当
B. 轨底坡不正确
C. 曲线方向不圆顺
D. 钢轨缺乏涂油措施
【多选题】
尖轨按断面形式分类中不含___尖轨。
A. 普通断面钢轨
B. 高型特种断面钢轨
C. 矮型特种断面钢轨
D. 直线型和曲线型
【多选题】
关于尖轨与基本轨不密贴原因的叙述,___是不确切的。
A. 尖轨顶铁过长,补强板螺栓凸出
B. 曲基本轨弯折点位置不对,造成转折器部分轨向不良
C. 基本轨或尖轨本事硬弯
D. 基本轨、轨撑、滑床板挡肩之间存在“三道缝”
【多选题】
关于尖轨跳动产生原因的叙述,___是不确切的。
A. 尖轨跟端轨缝过大,间隔铁和夹板磨耗,螺栓松动,过车时加大了冲击
B. 尖轨拱腰及跟桥型垫板或凸台压溃
C. 捣固不实,有吊板
D. 尖轨与基本轨不密贴或假密贴
【多选题】
关于预防整治尖轨跳动措施的叙述,___是不确切的。
A. 焊补或更换间隔铁、夹板,更换磨耗的双头螺栓
B. 调直拱腰的尖轨,增补整修跟桥型垫板和防跳卡铁
C. 尖轨顶铁过短
D. 加强转辙部分枕下的捣固,尤其是加强接头及尖轨跟端的捣固
【多选题】
关于导曲线轨距扩大的原因叙述,___是不正确的。
A. 列车与钢轨之间摩擦力
B. 列车横向推力
C. 车轮冲击钢轨
D. 列车离心力
【多选题】
关于导曲线外股钢轨侧面磨耗产生的原因叙述,___是不正确的。
A. 曲线外股没有设置 超高
B. 长期受离心力作用
C. 导曲线存在反超高
D. 导曲线轨距超限
【多选题】
关于辙叉轨距不合标准产生的原因叙述,___是不确切的。
A. 拨正直股方向
B. 查照间隔和护背距离不合标准
C. 护轨轮缘槽尺寸不合标准
D. 辙叉轮缘槽尺寸不合标准
【多选题】
无缝线路地段安排全年维修计划时,一般不考虑___。
A. 季节特点
B. 锁定轨温
C. 线路状态
D. 轨道类型
【多选题】
在线路上焊接钢轨时,气温不应低于___℃。
A. -5
B. 0
C. 5
D. 10
【多选题】
当断缝小于50mm时,应立即进行紧急处理。在断缝处上好夹板或臌包夹板,用急救器固定,在断缝前后各50m拧紧扣件,并派人看守,限速放行列车速度为___。
A. 5-10km/h
B. 15-25km/h
C. 1-5km/h
D. 10-15km/h
【多选题】
钢轨铝热焊焊缝接头应平整圆顺,用1m直尺测量,顶面、侧面不平度应在___以内,顶面不得有负值。
A. 0.5mm
B. 1mm
C. 1.5mm
D. 2mm
【多选题】
氧气瓶、丙烷瓶在焊接和切割火焰的上风方向和侧风方向,禁止布置在火焰的___方向的。
A. 前面
B. 上面
C. 上风
D. 下风
【多选题】
丙烷瓶与明火的距离不得小于___。
A. 3m
B. 5m
C. 10m
D. 15m
【多选题】
丙烷瓶与氧气瓶的距离不得小于___。
A. 3m
B. 5m
C. 10m
D. 15m
【多选题】
在钢轨焊接中,含碳量高的钢轨比含碳量低的可焊性___。
A. 好
B. 差
C. 一样
D. 任意
【多选题】
37°探头探测钢轨使用的是___。
A. 纵波
B. 横波
C. 表面波
D. 板波
【多选题】
70°探头探测轨头时只有二次波显示位移量较大应___。
A. 判轻伤
B. 判重伤
C. 不判伤
D. 进行校正后确认
【多选题】
超声波的波长___。
A. 与速度和频率成正比
B. 与速度成正比与频率成反比
C. 与速度成反比与频率成正比
D. 等于速度和频率的乘积
【多选题】
超声波到达两个不同材料的界面上,可能发生___。
A. 反射
B. 折射
C. 波形转换
D. 反射、折射和波形转换
【多选题】
被放大的信号幅度与缺陷的反射面积成正比地增大,放大器这一非饱和的放大区域称为___。
A. 灵敏度范围
B. 线性范围
C. 选择范围
D. 分辨率范围
【多选题】
超声波探伤仪中,产生时间基线的部分叫做___。
A. 扫描电路
B. 接收器
C. 脉冲器
D. 同步器
【多选题】
探测厚焊缝中垂直于表面的缺陷最适用的方法是___。
A. 聚焦探头
B. 直探头
C. 斜探头
D. 串列斜探头
【多选题】
钢轨焊缝中的各种缺陷最不容易检测的缺陷有___。
A. 光斑
B. 灰斑
C. 光斑和灰斑
D. 气孔
【多选题】
探头发射脉冲声波的___是表示探头频率特性的最合理的数据。
A. 频谱
B. 频宽
C. 波长
D. 频率
【多选题】
钢轨核伤的是由哪种原因发展形成的___。
A. 气泡
B. 夹渣
C. 外部冲击伤痕
D. 以上都是
【多选题】
同种材料中,在给定频率下产生波长短的波动形式是___。
A. 纵波
B. 压缩波
C. 横波
D. 表面波
【多选题】
因表面粗糙使超声波束产生的漫射叫做___。
A. 角度调整
B. 散射
C. 折射
D. 扩散
【多选题】
材料的声速与密度的乘积,可决定超声波在界面上的声能反射率与透过率,这一乘积称为___。
A. 声阻抗
B. 声速
C. 波长
D. 相位区
【多选题】
一定频率的超声波通过声速低的材料时,其波长将比通过声速高的材料时___。
A. 一样
B. 增长
C. 减短
D. 成倍增长
【多选题】
脉冲反射法,不适宜___探伤。
A. 厚件
B. 薄件
C. 任何
D. 任意
【多选题】
缺陷的当量尺寸总是___缺陷的实际尺寸。
A. 小于
B. 等于
C. 大于
D. 小于或等于
推荐试题
【单选题】
Which storage feature always requires the use of third-party software on ESXi?___
A. Hardware Acceleration for NAS devices
B. VVOL
C. Hardware Acceleration for Block
D. evices
【单选题】
An ESXi host's VMCA-Signed certificate has expired. How can the certificate be renewed?___
A. In the vSphere Web Client, browse to the host in question. Click the Manage tab and select settings. Select System and click Certificate, then click the Renew button.
B. In the vSphere Web Client, browse to the host in question. Click the Manage tab and select settings. Select System and click Certificate, then click the Refresh CA Certificates button.
C. Run the command /sbin/generate-certificates on the affected host.
D. Disconnect the host from vCenter Server and reconnect it.
【单选题】
Which is the correct order for upgrading vSphere components?___
A. vCenter Server, ESXi hosts, VMware Tools, Virtual Machine hardware
B. VMware Tools, Virtual Machine hardware, ESXi hosts, vCenter Server
C. vCenter Server, Virtual Machine hardware, VMware tools, ESXi hosts
D. ESXi hosts, vCenter Server, Virtual Machine hardware, VMware Tools
【单选题】
Which iSCSI initiator type can be used with any network interface card?___
A. Software iSCSI initiator
B. Software FCoE adapter
C. Hardware Independent iSCSI initiator
D. Hardware Dependent iSCSI initiator
【单选题】
An administrator is attempting to power on a virtual machine with 32GB of memory. The operation fails with the following error: <Could not power on VM: No space left on device> <Checking the space on the virtual machine's datastore, there is 30GB free.> Which action would allow the VM to power on?___
A. Set a 2GB memory reservation on the VM.
B. Mount the virtual disk from the affected VM on to another virtual machine and free up space from within the OS.
C. Enable vSphere HD admission control on the cluster in which the VM resides.
D. Set a 2GB memory limit on the VM.
【单选题】
An administrator attempts to manually reclaim space on thin-provisioned VMFS6 volumes but finds that no additional space is being recovered. Which could be causing this?___
A. vSphere 6.5 does not support manual UNMAP.
B. The manual UNMAP operation has been moved to the vSphere web client.
C. The VASA version is use is incompatible.
D. UNMAP is automated for VMFS6.
【单选题】
An administrator has upgraded to vSphere 6.5 and also wants to use Kerberos authentication for NFS. Which can be done to the existing NFSv3 volumes to enable this feature?___
A. Perform a storage rescan on VMFS volumes.
B. Unmount the NFSv3 datastore, and then mount as NFSv4.1 datastore.
C. Nothing. All NFSv3 mounted datastores are upgraded automatically during vSphere upgrades.
D. Perform a scan of new storage devices.
【单选题】
An administrator wants to restore the vCenter Server Appliance 6.5 from backup. Where can this be accomplished?___
A. from the ESXi Host Client
B. from the VMware vSphere Appliance Management Interface
C. from within the VMware vSphere Web Client
D. from the vCenter Server Appliance Installer
【单选题】
The administrator wants to power on VM-K2, which has a 2GHz CPU reservation. VM-M1, VM-M2, and VM-K1 are all powered on. VM-K2 is not powered on. The exhibit shows the parent and child resource reservations. If Resource Pool RP-KID is configured with an expandable reservation, which statement is true?___
A. VM-K2 will be unable to power on because there are insufficient resources.
B. VM-K2 will be able to power on since resource pool RP-KID has 2GHz available.
C. VM-K2 will be unable to power on because only 2GHz are reserved for RP-KID.
D. VM-K2 will receive resource priority and will be able to power on this scenario.
【单选题】
Which is the block size on the VMFS6 datastore?___
A. All small and large file blocks are 8MB.
B. All small and large file blocks are 1MB.
C. Small file blocks are 512KB. large file blocks are 64MB.
D. Small file blocks are 1MB, large file blocks are 512MB.
【单选题】
When installing vCenter Converter Standalone, why must an administrator perform a client-server installation instead of a local installation?___
A. to manage conversion tasks remotely
B. to convert virtual machines as well as physical machines
C. to allow installation of the Converter agent on remote source machines
D. to hot clone physical or virtual machines
【单选题】
Which is required by vCenter Converter Standalone to convert a physical Red Hat Enterprise Linux 7 machine to a virtual machine?___
A. The Linux machine must be powered off.
B. The Linux machine must have the SSH daemon started.
C. The Linux machine must use a static IP address.
D. The Linux machine must have a fully-qualified domain name.
【单选题】
An administrator is troubleshooting network communications between a vCenter Server and an ESXi 6.5 host. Which log shows the related events between these components?___
A. /var/log/fdm.log
B. /var/log/vpxa.log
C. /var/log/hostd.log
D. /var/log/auth.log
【单选题】
An administrator has recently upgraded from vSphere 6.0 to 6.5, and can no longer see the software iSCSI named vmhba33. Which could be the reason for this?___
A. The upgrade has changed the vmhba name.
B. vSphere 6.5 automates iSCSI configurations.
C. vSphere 6.5 no longer supports software iSCSI.
D. The upgrade has deleted the vmhba.
【单选题】
An administrator is trying to vMotion a VM from his datacenter to a recovery site. Which is the maximum allowed RTT (Round-Trip Time) latency between source and destination host?___
A. 100 milliseconds
B. 150 milliseconds
C. 15 milliseconds
D. 10 milliseconds
【单选题】
Which is required for configuring iSCSI Software Adapter network port binding?___
A. VMkernel of the iSCSI traffic must be load balanced using Route based on IP Hash algorithm.
B. VMkernel of the iSCSI traffic must be load balanced using Route based on Source Virtual Port ID algorithm.
C. VMkernel of the iSCSI traffic must be load balanced using Route based on Source MAC Hash algorithm.
D. VMkernel of the iSCSI traffic must be bound to only one active network adapter.
【单选题】
In vSphere Data Protection 6.1, which is the function of a Backup Verification job?___
A. None. Backup Verification job is not a feature of vSphere Data Protection
B. It is a manual task -Power it on -Verify the guest OS -Check started applications
C. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OS is booted by communicating with the Backup Verification agent
D. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OC is booted by detecting the VMware ToolsTM "heartbeats"
【单选题】
An administrator has enabled vSphere Distributed Switch Health Check. The hosts connected to that Distributed Switch all display an alert:< vSphere Distributed Switch MTU supported status > .The administrator has all of the VMkernel ports MTU sizes set to 1600. Which action will remedy this problem?___
A. Configure the Distributed Switch to MTU 9100.
B. Disconnect and reconnect the physical network cable.
C. Configure the physical switch to MTU 1600.
D. Disable the Distributed Switch MTU.
【单选题】
Which Host Profile Subprofile configuration is used to configure firewall settings for ESXi hosts?___
A. Advanced Configuration Settings
B. General System Settings
C. Security
D. Networking
【单选题】
Where would a vSphere administrator find general vCenter Server logs on a vCenter Server Appliance?___
A. /var/log/vmware/vpxd/
B. /var/log/messages
C. /etc/vmware-vpx/
D. /var/log/vmware/vsan-health/
【单选题】
An administrator wishes to enable network port mirroring based on source port. Which feature should be enabled?___
A. vSphere standard switch port
B. ERSPAN
C. NSX Virtual Wire
D. VLAN
【单选题】
Which CLI command shows the physical uplink status for a vmnic?___
A. esxcli network ip connection list
B. esxcli network ip neighbor list
C. esxcli network nic get
D. esxcli network nic list
【单选题】
Which is the maximum number of block devices (LUNs) that are supported by ESXi hosts that are running version 6.5?___
A. 1024
B. 512
C. 2048
D. 256
【单选题】
When performing a vCenter Server 5.5 for Windows with Microsoft SQL Server Express database migration to vCenter Server Appliance 6.5, which will be the target database?___
A. Microsoft SQL Server Express 2012R2
B. Microsoft SQL Server Standard 2012R2
C. PostgreSQL
D. Oracle DB 11g
【单选题】
An administrator has multiple vCenter Server 6.5 systems but cannot enable Storage I/O Control (SIOC) on a datastore shared by ESXi hosts managed by the vCenter Server systems. Which action should the administrator take to resolve the issue?___
A. Unmount the datastore and then enable SIOC on the vCenter Server system.
B. Configure the datastore to be managed by a single vCenter Server system.
C. Configure Storage DRS and then enable SIOC on the vCenter Server system.
D. Enable Raw Device Mapping (RDM) on the
E. SXi hosts.
【单选题】
“OneAppServer” is a VM template stored in a content library named “LibraryOne”, but the vSphere administrator is not able to use this template for deployment. Why is the administrator unable to deploy OneAppServer?___
A. OneAppServer must be updated before it can be deployed.
B. LibraryOne is a subscribed library and OneAppServer is not downloaded yet.
C. LibraryOne is published and optimized for syncing over HTTP.
D. OneAppServer was imported from a local file on the system.
【单选题】
An administrator sets the Failover Capacity for both CPU and Memory at 25%. Based on the Exhibit below, how much of the cluster’s total CPU resources are still available to power on additional virtual machines?___
A. 45%
B. 25%
C. 70%
D. 60%
【单选题】
Which statement applies to the vSphere Replication appliance?___
A. Only one vSphere Replication appliance can be deployed per vCenter Server instance.
B. VMware Tools in the vSphere Replication appliance can be upgraded.
C. A single vSphere Replication appliance can manage a maximum of 4000 replications.
D. vSphere Replication is available only with the vSphere
E. ssentials Plus license.
【单选题】
Which esxcli namespace can a vSphere Administrator use to adjust the queue depth?___
A. esxcli system module parameters
B. esxcli storage core device
C. esxcli system module set
D. esxcli storage core adapter
【单选题】
Which statement regarding datastore clusters meets VMware’s recommended best practices?___
A. Clusters should contain only datastores presented from the same storage array.
B. Clusters should contain only datastores with equal hardware acceleration capability.
C. Clusters should contain only datastores with the same capacity.
D. Clusters should contain only datastores using the same connection method (iSCSI, FC, etc.).
【单选题】
What VM Monitoring setting would ensure that the maximum reset window for a virtual machine is 24 hours?___
A. Medium
B. Low
C. High
D. Normal
【单选题】
What is the default space threshold for vSphere Storage DRS?___
A. 80%
B. 70%
C. 90%
D. 95%
【单选题】
Which is the correct sequence to upgrade a vSphere infrastructure?___
A. vCenter Server>ESXi host> VMware Tools>VM compatibility
B. ESXi host>vCenter Server> VMware Tools>VM compatibility
C. vCenter host> ESXi host> VM compatibility> VMware Tools
D. ESXi host>vCenter Server> VM compatibility>VMware Tools
【单选题】
An administrator has a large boot from SAN cluster and wants to ensure consistent configuration by using host profiles. What special considerations are required for boot from SAN hosts?___
A. Change the “Device is shared clusterwide” setting to “false” in the host profile.
B. Verify that the boot LUN is correctly identified as the boot device in the host profile.
C. The boot from SAN device must report as a local device.
D. Host profiles are incompatible with boot from SAN hosts.
【单选题】
When using VMware Converter to import a Windows server and improve the consistency of the destination virtual machine, which optional step can be performed immediately prior to powering down the source server?___
A. Perform a final synchronization task.
B. Remove the server from the network.
C. Uninstall production applications.
D. Remove the server from the Active Directory domain.
【单选题】
Restoration of the vCenter Server Appliance is accomplished using which interface?___
A. vSphere Web Client
B. vSphere Client
C. vCenter Server Appliance Management Interface
D. vCenter Server Appliance GUI Installer
【单选题】
When attempting to migrate a virtual machine to another host in the same cluster, the error message, “Select a valid compute resource” returns. What could cause this error?___
A. Both hosts run different versions of ESXi.
B. Both hosts are not sharing the same datastore.
C. VMware Tools is not installed.
D. Virtual machine has an ISO attached.
【单选题】
When will vSphere Data Protection delete the expired backup image of a Platform Service Controller?___
A. Immediately after the retention period has expired.
B. After the expired backup image is restored.
C. During the next backup window following expiry.
D. During the next maintenance window following expiry.
【单选题】
Group A has permission to download files in Content Library. Group B does not have permission to download files in Content Library. If a user is a member of both groups, what will be the result?___
A. The user cannot download file from Content Library.
B. The user can download file from Content Library.
C. The user cannot access Content Library.
D. The user can access Content Library.
【单选题】
An administrator is trying to set up Host Partial Failure Response, but the Automated option is grayed out. What can the administrator change to enable the Automated option?___
A. Change the vSphere DRS Automation level to Partially Automated.
B. Change the vSphere DRS Automation level to Fully Automated.
C. Enable vSphere HA Host Monitoring.
D. Change the vSphere DPM Automation level to Automatic.
欢迎使用我爱刷题
×
微信搜索我爱刷题小程序
温馨提示
×
请在电脑上登陆“www.woaishuati.com”使用