【单选题】
(71640)( )不是空调系统制冷不足的原因。[311120212](1.0分)___
A. 冷冻室绝热性能差
B. 膨胀阀流量太小
C. 系统内有空气
D. 制冷剂不足
查看试卷,进入试卷练习
微信扫一扫,开始刷题
相关试题
【单选题】
(71641)当制冷系统混有较多空气时,会使( )。[311120211](1.0分)___
A. 压缩机排气压力稍大于冷凝压力
B. 压缩机排气温度增高
C. 压缩机功耗降低
D. 冷凝器水温水压不变时,冷凝压力降低
【单选题】
(71642)当停留车达( )时,在该车运用前,其蓄电池需充电。[311120204](1.0分)___
A. 1个月
B. 1.5个月
C. 2个月
D. 2.5个月
【单选题】
(71643)KP-2A型控制箱的三相输出线电压为( )。[311120204](1.0分)___
A. 42 V
B. 43 V
C. 44 V
D. 45 V
【单选题】
(71644)正常的蓄电池在充电后,按正常放电制进行放电,如果放出的容量达不到额定容量的( ),就叫容量损失。[311110504](1.0分)___
A. 90%
B. 95%
C. 98%
D. 100%
【单选题】
(71645)现有客车J5型发电机轴端传动装置采用标准长轴斜套型,采用B型三角皮带( )。[311120304](1.0分)___
【单选题】
(71646)可控硅正向阻断峰值电压的数值,规定比正向转折电压小( )。[221110206](1.0分)___
A. 100 V
B. 120 V
C. 150 V
D. 180 V
【单选题】
(71647)在规定的环境温度和控制极断路及元件导通的条件下,要维持元件继续导通所需的( )电流,叫维持电流。[231110206](1.0分)___
A. 最小正向
B. 最大正向
C. 最小反向
D. 最大反向
【单选题】
(71648)使用空调机组空气预热时,须先开启( ),再开启电热。[311120204](1.0分)___
A. 压缩机
B. 通风
C. 冷凝器
D. 制冷
【单选题】
(71649).合上开关后,日光灯不亮的可能原因是( )。[213120404](1.0分)___
A. 开关短路
B. 开关接在零线上
C. 电路断路
D. 导线太粗
【单选题】
(71650)J5型发电机的额定电压直流输出( )。[311120306](1.0分)___
A. 12 V
B. 36 V
C. 48 V
D. 59 V
【单选题】
(71651)客车蓄电池用蒸馏水用电导试验时,其绝缘值( )。[331120202](1.0分)___
A. >0.3 M
B. <0.3 M
C. ≥0.3 M
D. ≤0.3 M
【单选题】
(71652)铅酸蓄电池放电时,阴阳极板表面都会逐渐形成( )薄层。[311110206(1.0分)___
A. Pb
B. PbO
C. PbO2
D. PbSO4
【单选题】
(71653)铅酸蓄电池在充电后,阴极板上会逐渐形成( )薄层。[312110206](1.0分)___
A. Pb
B. PbO
C. PbO2
D. PbSO4
【单选题】
(71654)铅酸蓄电池在充电后,阳极板上会逐渐形成( )薄层。[313110206](1.0分)___
A. Pb
B. PbO
C. PbO
D. PbSO4
【单选题】
(71655)空调列车电力连接线长度一般应为( )。[311120202](1.0分)___
A. 1 400~1 500 mm
B. 1 500~1 600 mm
C. 1 600~1 700 mm
D. 1 700~1 800 mm
【单选题】
(71656)BSP新型客车,其供电形式为集中供电,电压为( ),三相四线制。[313110302](1.0分)___
A. DC 600 V
B. AC 380
C. DC 110 V
D. DC 48 V
【单选题】
(71657)BSP客车电气系统的分类代码100系列表示( )。[313110210](1.0分)___
A. 供电系统
B. 照明系统
C. 空调系统
D. 轴报及制动系统
【单选题】
(71658)BSP客车电气系统的分类代码200系列表示( )。[313120210](1.0分)___
A. 供电系统
B. 照明系统
C. 空调系统
D. 轴报及制动系统
【单选题】
(71659).BSP客车电气件的代号根据IEC标准编排,元件代码B表示( )。[313110228](1.0分)___
A. 空调温度传感器,压力开关
B. 照明,加热装置
C. 熔断器
D. 指示灯,喇叭
【单选题】
(71660)BSP客车电气件的代号根据IEC标准编排,元件代码E表示( )。[313120228](1.0分)___
A. 空调温度传感器,压力开关
B. 照明,加热装置
C. 熔断器
D. 指示灯,喇叭
【单选题】
(71661).BSP客车蓄电池充电机电路控制板上电位器RP1的作用是( )。[313110211](1.0分)___
A. 调整输出电流反馈大小
B. 调整电流给定
C. 调节输出电压大小
D. 调节温度补偿电压反馈度
【单选题】
(71662)BSP客车蓄电池充电机电路控制板上电位器RP3的作用是( )。[313120211](1.0分)___
A. 调整输出电流反馈大小
B. 调整电流给定
C. 调节输出电压大小
D. 调节温度补偿电压反馈度
【单选题】
(71663)BSP客车AC 380 V供电线路中如果闭合空气断路器Q201,得电的是( )。[312120205](1.0分)___
A. 温水箱得电
B. 电开水炉
C. 蓄电池充电机
D. 三相变压器
【单选题】
(71664)BSP客车AC 220 V供电线路中如果闭合空气断路器Q1100,给( )送电。[313120205](1.0分)___
A. 座式厕所冲水系统
B. 蹲式厕所冲水系统
C. 洗手间排水管电伴热
D. 客室信息显示屏
【单选题】
(71665)BSP客车DC 48 V应急负载供电线路中闭合空气断路器Q701,( )得电。[321120205](1.0分)___
A. 空调CPU中央控制单元
B. 塞拉门控制装置
C. 防滑控制器
D. 应急照明控制回路
【单选题】
(71666)BSP客车一般直流负载和应急负载的电压为( )。[312120306](1.0分)___
A. DC 24 V
B. DC 110 V
C. DC 220 V
D. DC 48 V
【单选题】
(71667)BSP客车一般直流负载的电流为( )。[312110223](1.0分)___
A. 25 A
B. 10 A
C. 19 A
D. 40 A
【单选题】
(71668).BSP客车充电机无充电电流的原因是( )。[312110204](1.0分)___
A. 充电支路熔断器RD2(RL8-20A)芯断
B. 充电机控制板上个别电子元器件坏
C. 蓄电池箱内的温度传感器坏
D. ABC三项
【单选题】
(71669)BSP客车充电机应急供电不能自动切换的原因是( )。[322110204](1.0分)___
A. 主电路中直流接触器不吸合
B. 充电机控制板上个别电子元器件坏
C. 蓄电池电压在DC 42 V以下
D. ABC三项
【单选题】
(71670)BSP客车充电机在使用时应注意:在车辆整备长期放置不用时,尽量每隔( )给蓄电池充一次电,并注意将蓄电池箱内的断路器断开。[312120304](1.0分)___
A. 1个月
B. 3个月
C. 6个月
D. 1年
【单选题】
(71671)TCL-12型开水炉控制箱上工作指示灯连续闪烁两次表明( )。[313110204](1.0分)___
A. IGBT管温度过高或进水温度超过45 ℃
B. IGBT管过热损坏
C. 开水炉处于保温状态
D. 开水炉处于加热状态
【单选题】
(71672)电开水炉进水电磁阀关闭不严不会造成( )。[312110204](1.0分)___
A. 开水炉不工作
B. 出水温度过低
C. 溢气管溢水比较多
D. 产温水
【单选题】
(71673)轴温传感器的有两根导线“+”和“-”,其含义是( )。[322120214](1.0分)___
A. )“+”代表电源正线,“-”代表电源负线
B. “+”和“-”都是信号线
C. “+”代表公共线,“-”代表通信线
D. “+”代表通信线,“-”代表公共线
【单选题】
(71674)快达KD-3型电开水炉的3号电极的作用是( )。[312110205](1.0分)___
A. 冷水箱水位低于此电极时,电磁阀自动通电进水
B. 冷水箱水位高于此电极时,电磁阀自动断电停止进水
C. 冷水箱水位低于此电极时,煮水箱内的发热管自动断电停止工作
D. 冷水箱水位高于此电极时,煮水箱内的发热管自动通电开始工作
【单选题】
(71675)TCL-12型开水炉工作指示灯亮但不加热有可能由( )原因造成。[312120404](1.0分)___
A. 感应线圈与加热腔绝缘击穿
B. 感应线圈开路
C. 水位显示及传感器组件失效
D. 电磁阀故障
【单选题】
(71676)KSL-Ⅲ型电开水炉工作正常但始终无法到达满水位,其原因可能是( )。[312110404](1.0分)___
A. 溢气管堵塞
B. 缺水保护器作用不良
C. 电源缺相
D. 电加热管开路
【单选题】
(71677)造成KSL-Ⅲ型电开水炉开关置“通”位后接触器吸合时、配电室空气开关跳闸,其原因可能是( )。[313120404](1.0分)___
A. 进水管堵塞
B. 电热管或电源线有对地短路现象
C. 缺水或满水保护干簧管绝缘不良
D. 电磁阀损坏
【单选题】
(71678)KZS/M-Ⅰ型轴温报警器的正常工作电压是( )。[322120214](1.0分)___
A. 42~60 V
B. 36~60 V
C. 36~72 V
D. 42~72 V
【单选题】
(71679)利用TFX1型电子防滑器测试塞拉门5 km/h的保护作用是否良好应( )。[313210216](1.0分)___
A. 按“诊断”按钮超过5 s进入自检,直至显示“88”说明作用良好
B. 按“显示”按钮超过5 s进入自检,直至显示“88”说明作用良好
C. 同时按“显示”和“诊断”按钮超过5 s进入自检,直至显示“88”说明作用良好
D. 同时按“清除”和“诊断”按钮超过5 s进入自检,直至显示“88”说明作用良好
【单选题】
(71680)KSL-Ⅲ型电开水炉主要元件为( ),在工作时主要由磁性浮球上升或下降,实现自动加热或发出报警停止加热作用。[322110223](1.0分)___
A. UK1干簧管
B. 电磁阀
C. 接触器
D. 继电器
推荐试题
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
【单选题】
An administrator is installing Windows into a virtual machine. The DVD has been mounted on the Host and configured for the virtual machine as shown in the Exhibit. Based on the exhibit, when the virtual machine is booted, why would it attempt to search for a PXE server? ___
A. The CD/DVD device is not connected.
B. The ISO is in the incorrect storage location.
C. The OS minimum requirements have not been met.
D. The CD/DVD device is not set to Client Device.
【单选题】
What component must be installed prior to deploying a vCenter Server in vSphere 6.x? ___
A. vCenter Identity Services
B. Platform Services Controller
C. vCenter Single Sign-On
D. Client Integration Plug-In
【单选题】
What is a valid plug-in status for a plug-in that has been added to a vSphere client? ___
A. Disabled
B. Unknown
C. Stopped
D. Installed
【单选题】
Users of an application are reporting performance issues. The following performance values are observed in the vSphere Web Client: <Host CPU utilization is 90%> <Virtual Machine memory utilization is consistently greater than 90% CPU Ready values are higher than 20%> What could be the cause of the application performance issue? ___
A. The host is lacking the CPU resources required to meet the demand.
B. The host is lacking the memory resources required to meet the demand.
C. The virtual machine is lacking the CPU resources required to meet the demand.
D. The virtual machine is lacking the memory resources required to meet the demand.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is re-provisioning an ESXi host and moving it to another datacenter. Which DCUI option should the administrator use to revert the system configuration to the default settings? ___
A. Reset System Configuration
B. Rebuild Default System Configuration
C. Revert System Configuration
D. Renew Default System Configuration
【单选题】
An administrator has just completed installing an ESXi 6.x host, but doesn't know what address has been configured. Where is the ESXi host IP address configured? ___
A. RVC console
B. Direct Console User Interface
C. vSphere Web Client
D. vSphere Client
【单选题】
When is it possible to place a VMFS5 datastore in maintenance mode? ___
A. When it is a member of a Storage DRS cluster
B. When it is a member of Virtual SAN cluster
C. When it is a member of a multi-extent datastore
D. When it is a member of a Virtual Volume
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Which Single Sign-On deployment mode should an administrator use for two 6.x vCenter Servers configured with linked mode? ___
A. Basic Single Sign-On with vCenter Server Heartbeat
B. Multisite Single Sign-On
C. Basic Single Sign-On
D. Single Sign-On with Linked Mode
【单选题】
What is required when changing a virtual machine name using the vSphere Web Client? ___
A. Verify connectivity to the ESXi host where the virtual machine is running and its inventory list is accessible.
B. Verify in which datastore the virtual machine resides and that you have access and its inventory list is accessible.
C. Verify that virtual machine files are stored in the same datastore and can be accessed in the datastore browser list.
D. Verify the virtual machine is not running in Fault Tolerant mode and that it is not in a Distributed Resource Scheduler cluster.
【单选题】
An administrator deploys vRealize Operations into a vSphere 6.x environment. After the deployment, the administrator notices that badges are not appearing. What is a likely cause of this behavior? ___
A. Badges do not appear until you register vRealize Operations with vCenter Server.
B. Badges do not appear until you register a vCenter Server in vRealize Operations.
C. The vRealize Operations appliance needs to be redeployed.
D. The vCenter Server appliance needs to be redeployed.
【单选题】
How are ports scaled on vSphere Standard Switches (vSS)? ___
A. Ports on a vSS can be dynamically scaled up and down.
B. Ports on a vSS can only be statically scaled up or down.
C. Ports on a vSS can only be dynamically scaled down.
D. Ports on a vSS can only be dynamically scaled up.
【单选题】
A High Availability (HA) cluster is configured to respond to a given number of host failures. The cluster contains virtual machines configured with these settings: VM1 has a 1GHz CPU reservation and no Memory reservation VM2 has a 2GHz CPU reservation and no Memory reservation VM3 has no CPU reservation and no Memory reservation . Given this information, what is the correct slot size for the cluster? ___
A. The CPU Reservation should be set to 32MHz and the memory reservation should be set to 32MB plus memory overhead.
B. The CPU reservation should be set to 1 GHz and the memory reservation should be set to 0MB plus memory overhead.
C. The CPU reservation should be set to 2 GHz, and the memory reservation should be set to 0MB plus the virtual machine memory overhead.
D. The CPU reservation should be set to 2 GHz, and the memory reservation should be set to 32MB, plus the virtual machine memory overhead.
【单选题】
An administrator is planning a vSphere infrastructure with the following specific networking requirements: <The ability to shape inbound (RX) traffic> <Support for Private VLANs (PVLANs)> <Support for LLDP (Link Layer Discovery Protocol)>. What is the minimum vSphere Edition that will support these requirements? ___
A. vSphere Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
【单选题】
When you add an ESXi 6.x host to a new Cluster, which vSphere object owns the CPU and Memory resources of the hosts? ___
A. vCenter Server
B. Datacenter
C. Cluster
D. Host
【单选题】
A user is trying to retrieve objects from a SharePoint server and finds the request is taking an excessive amount of time. An administrator tries to isolate the issue and notes the following: Application performance is poor when compared to virtual machines on other hosts. Performance improves when the virtual machine is moved to another host. The virtual machine encounters higher than expected CPU %Ready times. What conclusion can be reached regarding the performance issues for this virtual machine? ___
A. Host Power Management is directly impacting virtual machine performance.
B. The virtual machine has a large number of snapshots.
C. The Path Selection Policy for the storage device is set differently on the affected host.
D. Network I/O control is configured for the portgroup.
【单选题】
A virtual machine template is accidently removed from the vCenter Server Inventory. Which method would be used to recover the template back into the environment?___
A. Use the datastore browser to locate the template, then right click and add the .vmtx file to inventory.
B. Use the datastore browser to locate the template, then right click and add the .vmx file to inventory.
C. Using the Managed Object Browser and adding the template from the ManagedObjectReference:GuestFileManager object.
D. Using the Managed Object Browser and adding the template from the ManagedObjectReference:VirtualDiskManager object.
【单选题】
A vSphere administrator needs to backup a virtual machine that has a Microsoft SQL Server Database installed. Which solution allows for an application quiesce to occur during backup?___
A. VMware vCenter Converter
B. VMware vCenter Site Recovery Manager
C. VMware vSphere Replication
D. VMware vSphere Data Protection Advanced
【单选题】
An administrator is migrating a virtual machine from a Test cluster to a Production cluster. The two environments do not have any shared storage. What is the easiest way to accomplish this task? ___
A. Perform a Storage vMotion.
B. Perform a regular vMotion.
C. Perform a Virtual to Virtual migration.
D. Perform a backup and restore using VMware Data Protection.
【单选题】
An administrator must determine an appropriate backup solution, given these conditions: 50 of the virtual machines are in a resource pool named Finance. 50 of the virtual machines are in a resource pool named QA. Which solution allows an administrator the ability to backup 100 virtual machines? ___
A. Use Snapshot Manager on the vCenter Server to backup the virtual machines.
B. Use the VMware Consolidated Backup (vcb) tool on the ESXi Host to backup the virtual machines.
C. Use the VMware Data Recovery (VDR) Appliance on the vCenter Server to backup the virtual machines.
D. Use the VMware Data Protection (VDP) Appliance on one of the
E. SXi Hosts to backup the virtual machines.
【单选题】
What is a benefit of using Enhanced vMotion Compatibility for an environment? ___
A. EVC masks CPU features to allow compatibility between hosts that are dissimilar.
B. EVC allows for cross platform vMotion to occur.
C. EVC enables Long
D. istance vMotion.
【单选题】
How many Link Aggregation Groups (LAGs) can be configured on a vSphere 6.x Distributed Switch? ___
A. 64
B. 96
C. 128
D. 256
【单选题】
How many Link Aggregation Groups (LAGs) can be configured on a vSphere 6.x Distributed Switch? ___
A. 64
B. 96
C. 128
D. 256
【单选题】
An administrator needs to verify that vMotion operations can be performed in a vSphere data center.What round trip time (RTT) latency is the maximum value that will allow vMotion operations to succeed? ___
A. 50ms RTT
B. 100ms RTT
C. 150ms RTT
D. 200ms RTT
【单选题】
A storage administrator has reported that full utilization of all bandwidth from an ESXi 6.x host is not being seen. In troubleshooting the issue, the Adapter details are shown in the Exhibit. Based on the exhibit, what is cause of the issue? ___
A. The array is not setup to use the correct multipathing policy.
B. There are no virtual machines on the ESXi host.
C. Not all links are used because a path is disabled.
D. Another path needs to be configured.