刷题
导入试题
【单选题】
第1669题:乙懦深冷区域设备安装多层保冷层时.要避免不同层上的纵横节点重愈.最小错幵距离___mm。
A. 100
B. 150
C. 200
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
B
解析
暂无解析
相关试题
【单选题】
第1670题:可燃气体混合物的初始温度越高,使爆炸下限___,上限増高,爆炸极限范围增大。
A. 增高
B. 降低
C. 不变
【单选题】
第1671题:二甲烷化反应饗的温度联锁动作条件一一般是只要有___温度达联锁值。
A. 一处
B. 两处
C. 三处
【单选题】
第1672题:乙烯装置裂解炉区与裂解气预分分馏区之间需设置水幕以防止火灾漫延。水幕供水压力应在___MPA 以上。
A. 0.45
B. 0.3
C. 0.7
【单选题】
第1673题:应急预案中___信息应由事故现场指挥部及时准确向新间媒体通报。
A. 救援
B. 事故
C. 伤亡
【单选题】
第1674题:关于设备的防静电措施,下列选项不正确的是___。
A. 静电接地
B. 易燃易爆液体进料采用顶部喷入
C. 输送易燃易爆液体要控制流速
【单选题】
第1675題:压缩机房上的危害有___。
A. 振动危害
B. 电击伤
C. 噪声危害
【单选题】
第1676题:衡量可燃性液体火灾危险性大小的主要参数是___。
A. 沸点
B. 闪点
C. 燃点
【单选题】
第1677题:酸雨的PH值小于___。
A. 5.6
B. 4.6
C. 6.0
【单选题】
第1678题:在管式裂解炉的使用规定中,炉管的渗碳不应大于管壁厚的___%。
A. 50
B. 40
C. 60
【单选题】
第1679题:在燃烧过程中,火焰主要以___形式向表层液体传入大量热,使表层液体蒸发,燃烧持续进行。
A. 辐射
B. 传导
C. 对流
【单选题】
第1680题:乙烯装置所用的原料、中间产品和产品大多是易燃易爆的气体或液体,如果安全措施不当,会有爆炸的危 险。乙烯装置中发生的化学爆炸的种类不包括___。
A. 混合气体爆炸
B. 扩散气体爆炸
C. 气体分解爆炸
【单选题】
第1681题:关于离心泵气缚的现象,下列选项中正确的___。
A. 泵出口压力高
B. 电机电流高
C. 泵出口流量低
【单选题】
第1682题:丙烯在工作环境中最高允许浓度为___mg/m。
A. 100
B. 200
C. 300
【单选题】
第1683题:稀释蒸汽发生系统腐蚀的预防措施有___。
A. 控制工艺水PH值在10-12之间
B. 控制稀释蒸汽汽包的连续排污量
C. 向汽油分馏塔汽油回流中注入汽油阻聚剂
【单选题】
第1684题:裂解炉风机振动声音大的原因是___。
A. 转速下降
B. 油脂过多
C. 轴承损坏
【单选题】
第1685题:甲烷化反应床层温度偏低,将可能导致___。
A. 剧毒羰基镍的生成
B. 甲烷化反应器堵塞
C. 甲烷化催化剂失活
【单选题】
第1686题:透平压缩机停车后,即刻盘车的目的是___。
A. 避免转子弯曲变形
B. 加快机体降温
C. 对压缩机进行检查
【单选题】
第1688题:危险化学品、烟花爆竹、民用爆炸物品生产企业预案未通过专家评审的不得颁发___。
A. 安全经营许可证
B. 安全生产许可证
C. 危险化学品登记证
【单选题】
第1689題:生产装置废水主要排放点是___。
A. 物料分液罐
B. 物料管线低洼点
C. 采样点
【单选题】
第1690题:腐蚀性流体介质与金属表面在相对运动中引起金属的加速腐蚀称为___。
A. 缝隙腐蚀
B. 冲蚀
C. 晶间腐蚀
【单选题】
第1691題:一般压力越高,可燃物的自燃点___。
A. 越高
B. 不变
C. 越低
【单选题】
第1692题:压缩机润滑油三级过滤的目的是防止润滑油在___过程中带入杂质。
A. 管理
B. 运输
C. 加注
【单选题】
第1693题:消防水泵房及其配电室应设消防应急照明,照明可采用蓄电池作备用电源,其连续供电时间不应少于___min
A. 20
B. 30
C. 15
【单选题】
第1 694题:关于精馅塔塔压联锁的原因.下列说法正确的是___。
A. 塔顶采出量过大
B. 加热量太小
C. 进料中轻分含量过高
【单选题】
第1695题:发现裂解炉原料罐冒罐的应急处理流程正确的是___。
A. 报警→现场确认、报告→切断泄露源→启动应急程序
B. 现场确认、报告→切断泄露源→报警→启动应急程序
C. 切断泄露源→现场确认、报告→报警→启动应急程序
【单选题】
第1696題:特种劳动防护用品实行生产___。
A. 申请制度
B. 监督制度
C. 许可证制度
【单选题】
第1697题:对学校、医院等人员密集场所的建设工程,应当按照___当地房屋建筑的抗震设防要求进行设计和施工、采取有效措施,増强抗震设防能力。
A. 等于
B. 低于
C. 高于
【单选题】
第1698题:安全标志分为四类,它们分别是___。
A. 通行标志、禁止通行标志、提示标志和警告标志
B. 禁止标志、警告标志、指令标志和提示标志
C. 禁止标志、警告标志、通行标志和提示标志
【单选题】
第1699题:进行有关化学液体的操作时,为保护面部应使用___。
A. 太阳镜
B. 防护面罩
C. 毛巾
【单选题】
第1700题:氨工作场所每月至少进行一次作业环境职业病危害因素监测,每___至少进行一次控制效果评价。
A. 季度
B. 月
C. 半年
【单选题】
第1701题:按照职业性接触毒物危害程度分级,苯属于___级。
A. Ⅰ
B. Ⅱ
C. Ⅲ
【单选题】
第1702题:碳三加氢反应为___反应,必须严格控制温度,以防飞温引起恶性事故。
A. 放热
B. 吸热
C. 中和
【单选题】
第1703题:生产经营单位的从业人员有依法获得安全生产保障的权利,并应当依法履行安全生产方面的___。
A. 责任
B. 义务
C. 工作
【单选题】
第1704题:下列不属于工业上常见的板式塔的是___
A. 筛板塔
B. 填料塔
C. 浮阀塔
【单选题】
第1705题:发生氢气泄露事故时,处理的注意事项不包括___。
A. 避免产生火花
B. 要防静电
C. 要在下风口处理
【单选题】
第1706题:用于高处作业的安全帯适用于体重及负重之和不大于___kg。
A. 100
B. 110
C. 120
【单选题】
第1707题:从事使用高毒物品作业的用人单位应当至少每___进行一次职业中毒危害控制效果评价。
A. 半年
B. 年
C. 两年
【单选题】
第1708题:向用人单位提供可能产生职业病危害的设备的,应当提供中文说明书,并在设备的醒目位置___。
A. 张贴中文说明书
B. 设置警示标识和中文警示说明
C. 设置安全注意事项
【单选题】
第1709题:裂解炉导向管与定位管之间间隙___mm。
A. 10-15
B. 10-20
C. 15-25
【单选题】
第1710题:乙烯装置所用的原料、中间产品和产品大多是易燃易爆的气体或液体,如果安全措施不当会有爆炸的危 险。乙烯装置中发生的化学爆炸的种类不包括___爆炸。
A. 混合气体
B. 扩散气体
C. 气体分解
推荐试题
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
【单选题】
An administrator is installing Windows into a virtual machine. The DVD has been mounted on the Host and configured for the virtual machine as shown in the Exhibit. Based on the exhibit, when the virtual machine is booted, why would it attempt to search for a PXE server? ___
A. The CD/DVD device is not connected.
B. The ISO is in the incorrect storage location.
C. The OS minimum requirements have not been met.
D. The CD/DVD device is not set to Client Device.
【单选题】
What component must be installed prior to deploying a vCenter Server in vSphere 6.x? ___
A. vCenter Identity Services
B. Platform Services Controller
C. vCenter Single Sign-On
D. Client Integration Plug-In
【单选题】
What is a valid plug-in status for a plug-in that has been added to a vSphere client? ___
A. Disabled
B. Unknown
C. Stopped
D. Installed
【单选题】
Users of an application are reporting performance issues. The following performance values are observed in the vSphere Web Client: <Host CPU utilization is 90%> <Virtual Machine memory utilization is consistently greater than 90% CPU Ready values are higher than 20%> What could be the cause of the application performance issue? ___
A. The host is lacking the CPU resources required to meet the demand.
B. The host is lacking the memory resources required to meet the demand.
C. The virtual machine is lacking the CPU resources required to meet the demand.
D. The virtual machine is lacking the memory resources required to meet the demand.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is re-provisioning an ESXi host and moving it to another datacenter. Which DCUI option should the administrator use to revert the system configuration to the default settings? ___
A. Reset System Configuration
B. Rebuild Default System Configuration
C. Revert System Configuration
D. Renew Default System Configuration
【单选题】
An administrator has just completed installing an ESXi 6.x host, but doesn't know what address has been configured. Where is the ESXi host IP address configured? ___
A. RVC console
B. Direct Console User Interface
C. vSphere Web Client
D. vSphere Client
【单选题】
When is it possible to place a VMFS5 datastore in maintenance mode? ___
A. When it is a member of a Storage DRS cluster
B. When it is a member of Virtual SAN cluster
C. When it is a member of a multi-extent datastore
D. When it is a member of a Virtual Volume
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Which Single Sign-On deployment mode should an administrator use for two 6.x vCenter Servers configured with linked mode? ___
A. Basic Single Sign-On with vCenter Server Heartbeat
B. Multisite Single Sign-On
C. Basic Single Sign-On
D. Single Sign-On with Linked Mode
【单选题】
What is required when changing a virtual machine name using the vSphere Web Client? ___
A. Verify connectivity to the ESXi host where the virtual machine is running and its inventory list is accessible.
B. Verify in which datastore the virtual machine resides and that you have access and its inventory list is accessible.
C. Verify that virtual machine files are stored in the same datastore and can be accessed in the datastore browser list.
D. Verify the virtual machine is not running in Fault Tolerant mode and that it is not in a Distributed Resource Scheduler cluster.
【单选题】
An administrator deploys vRealize Operations into a vSphere 6.x environment. After the deployment, the administrator notices that badges are not appearing. What is a likely cause of this behavior? ___
A. Badges do not appear until you register vRealize Operations with vCenter Server.
B. Badges do not appear until you register a vCenter Server in vRealize Operations.
C. The vRealize Operations appliance needs to be redeployed.
D. The vCenter Server appliance needs to be redeployed.
【单选题】
How are ports scaled on vSphere Standard Switches (vSS)? ___
A. Ports on a vSS can be dynamically scaled up and down.
B. Ports on a vSS can only be statically scaled up or down.
C. Ports on a vSS can only be dynamically scaled down.
D. Ports on a vSS can only be dynamically scaled up.
【单选题】
A High Availability (HA) cluster is configured to respond to a given number of host failures. The cluster contains virtual machines configured with these settings: VM1 has a 1GHz CPU reservation and no Memory reservation VM2 has a 2GHz CPU reservation and no Memory reservation VM3 has no CPU reservation and no Memory reservation . Given this information, what is the correct slot size for the cluster? ___
A. The CPU Reservation should be set to 32MHz and the memory reservation should be set to 32MB plus memory overhead.
B. The CPU reservation should be set to 1 GHz and the memory reservation should be set to 0MB plus memory overhead.
C. The CPU reservation should be set to 2 GHz, and the memory reservation should be set to 0MB plus the virtual machine memory overhead.
D. The CPU reservation should be set to 2 GHz, and the memory reservation should be set to 32MB, plus the virtual machine memory overhead.
【单选题】
An administrator is planning a vSphere infrastructure with the following specific networking requirements: <The ability to shape inbound (RX) traffic> <Support for Private VLANs (PVLANs)> <Support for LLDP (Link Layer Discovery Protocol)>. What is the minimum vSphere Edition that will support these requirements? ___
A. vSphere Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
欢迎使用我爱刷题
×
微信搜索我爱刷题小程序
温馨提示
×
请在电脑上登陆“www.woaishuati.com”使用