刷题
导入试题
【单选题】
硫磺优等品的含水量要求是___。
A. ≤1.0%
B. ≤0.3%
C. ≤0.5%
D. ≤0.1%
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
D
解析
暂无解析
相关试题
【单选题】
下列___不属于硫化氢气体的性质。
A. 比空气轻
B. 在空气中易燃烧
C. 无色气体
D. 有臭鸡蛋气味
【单选题】
纯硫化氢在空气中达到___℃发生自燃。
A. 170
B. 220
C. 232
D. 260
【单选题】
硫磺的分子量为___。
A. 16
B. 32
C. 48
D. 60
【单选题】
硫磺在150℃时呈___。
A. 黄色
B. 暗棕红色
C. 橙黄色
D. 无色
【单选题】
硫磺气化后,在900℃时为___气体。
A. 橙黄
B. 草黄色
C. 暗棕
D. 无色
【单选题】
克劳斯催化剂还原操作目的是___。
A. 延长催化剂使用寿命
B. 避免催化剂表面硫化氢中毒
C. 避免催化剂表面积碳自燃
D. 避免硫化亚铁自燃
【单选题】
MDEA溶剂配制时,MDEA和水的比例为___。
A. 2:1
B. 3:2
C. 1:1
D. 1:2
【单选题】
MDEA是___的英文缩写。
A. N-甲基二乙醇胺
B. 二异丙醇胺
C. 二乙醇胺
D. 单乙醇胺
【单选题】
开工氮气置换空气的一般安全标准是含氧量不大于___(v)。
A. 5%
B. 2%
C. 1%
D. 0.5%
【单选题】
一般情况,硫磺瓦斯管道吹扫气密是使用___。
A. 蒸汽
B. 氮气
C. 新鲜水
D. 动力风
【单选题】
吹扫酸性气管道最好的吹扫介质是___。
A. 蒸汽
B. 氮气
C. 新鲜水
D. 动力风
【单选题】
以下___不是酸性气分析项目。
A. H2S
B. SO2
C. S
D. H2O
【单选题】
硫化氢在装置内允许浓度为≤___mg/m3。
A. 1
B. 5
C. 10
D. 20
【单选题】
4#滤毒罐的防护对象是___。
A. 有机气体
B. 三苯
C. 二氧化碳
D. 硫化氢和氨
【单选题】
蒸汽灭火时站立位置正确操作是___。
A. 下风向
B. 上风向
C. 火源中心
D. 四周走动
【单选题】
如果在一定的范围内有毒气体浓度大于___%,滤毒罐是不可以使用的。
A. 4
B. 3
C. 2
D. 1
【单选题】
当气密过程中有泄漏,正确的做法是___。
A. 直接紧固
B. 继续升压
C. 降到安全压力紧固
D. 边升压边紧固
【单选题】
公用工程系统分别用___按最高操作压力进行气密试漏。
A. 蒸汽
B. 氮气
C. 本系统介质
D. 动力风
【单选题】
装置引蒸汽时防止“水击”的方法___。
A. 迅速开启蒸汽阀
B. 先开放空阀放尽冷凝水;再缓慢开启蒸汽阀
C. 开蒸汽阀时关闭放空阀
D. 先开蒸汽阀再打开末端放空阀
【单选题】
在蒸汽管道投用时首先要进行___操作。
A. 加热
B. 冷却
C. 小流量暖管
D. 大流量暖管
【单选题】
装置引蒸汽时,在蒸汽管线未端和低点处___放空阀( )蒸汽阀。
A. 先开、后开
B. 先关、再开
C. 先开、再关
D. 后开、先开
【单选题】
引蒸汽的时候,由于高温蒸汽与管道中的冷凝水接触,冷凝水升温,发生___,体积迅速膨胀,出现“汽锤”,使管道猛烈抖动,称为“水击”。
A. 化学反应
B. 相变
C. 爆炸
D. 冷凝
【单选题】
蒸汽试压时要注意低点___。
A. 排凝
B. 放气
C. 关闭
D. 保护
【单选题】
下列不是系统引氮气时所应注意的点是___。
A. 引氮气时注意安全,防止窒息
B. 氮气进装置后,凡需进入容器内必须要进行氧含量分析
C. 与氮气管线相连的其他工艺介质管线、容器用盲板或双阀隔离,双阀之间的放空打开
D. 引氮气前系统需进行干燥
【单选题】
下列关于低压系统吹扫的说法不正确的是___。
A. 管线的吹扫原则上要顺流程走向,先副线,后主线,顺管线向下或水平吹扫,避免向上吹扫
B. 先对各塔、容器吹扫,再向外吹附属设备及管线
C. 从外往塔、容器内吹扫,则必须先对入塔、容器管线吹扫干净,并在入塔、容器处拆开法兰排污,吹扫干净后再将法兰复位
D. 吹扫流程中的调节阀、孔板及流量计等元件应拆除
【单选题】
吹扫控制阀时,应___。
A. 先扫正线,后扫副线
B. 先扫副线,后扫正线
C. 正、副线同时扫
D. 没有特别原则
【单选题】
新装置开车水冲洗使用___。
A. 新鲜水
B. 循环水
C. 除盐水
D. 除氧水
【单选题】
塔的吹扫结束的标志正确的是___。
A. 塔顶放空无物料气出来
B. 塔底液面计上放空无物料气出来
C. 塔底放空无物料气出来
D. 塔底液面计下放空无物料气出来
【单选题】
引循环水时将冷换设备的操作不正确得是___。
A. 冷换设备出口前的放空阀打开将管道和冷换设备内的空气赶走
B. 引循环越慢越好
C. 先引介质再引循环水
D. 先将循环水冷换设备中垃圾吹扫掉
【单选题】
循环水进装置温度一般不会低于___。
A. 40℃
B. 30℃
C. 生活用水温度
D. 气温
【单选题】
循环水由于循环水冷却器的___要求,比新鲜水要求高。
A. 冷却
B. 防腐防垢
C. 流速
D. 回用
【单选题】
净化风与非净化风的主要区别是___。
A. 温度
B. 脱水
C. 比重
D. 使用量
【单选题】
吹扫换热器时,应___。
A. 先扫正线,后扫副线
B. 先扫副线,后扫正线
C. 正、副线同时扫
D. 没有特别原则
【单选题】
酸性气带水对硫磺装置的影响,以下哪项不正确___。
A. 造成炉膛熄火
B. 系统压力升高
C. 增加设备腐蚀
D. 提高催化剂水解反应效果
【单选题】
以下___不是酸性气中的液相组分。
A. 氨
B. 胺液
C. 碱液
D. 水
【单选题】
蒸汽再沸器在投用时,为了防止出现“水锤”,___进行预热。
A. 略微开启进口阀门
B. 开足进口阀门
C. 略微开启排凝阀门
D. 开足排凝阀门
【单选题】
进入反应炉的酸性气主要成分是___。
A. 硫化氢、氨、烃
B. 硫化氢、二氧化硫、烃
C. 硫化氢、二氧化碳、氨
D. 硫化氢、烃
【单选题】
在开车过程中,蒸汽重沸器在投用时,引物料的速度___比较好。
A. 越快越好
B. 先快后慢
C. 越慢越好
D. 先慢后快
【单选题】
现场玻璃板液面与仪表显示液位一致是因为仪表液位与现场液位___。
A. 手阀位置相同
B. 同一根引出管
C. 材质相同
D. 介质密度相同
【单选题】
调节阀是通过改变___来改变阀的阻力系数,达到调节流量的目的。
A. 阀芯行程
B. 信号压力的大小
C. 电信号的大小
D. 以上全部
推荐试题
【单选题】
Which type of firewall can perform deep packet inspection?___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
18.交流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
19.直流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
20.接触器的额定电压应不小于主电路的___。
A. 短路电压
B. 工作电压
C. 最大电压
D. 峰值电压
【单选题】
21.接触器的额定电流应不小于被控电路的___。
A. 额定电流
B. 负载电流
C. 最大电流
D. 峰值电流
【单选题】
22.对于___工作制的异步电动机,热继电器不能实现可靠的过载保护。
A. 轻载
B. 半载
C. 重复短时
D. 连续
欢迎使用我爱刷题
×
微信搜索我爱刷题小程序
温馨提示
×
请在电脑上登陆“www.woaishuati.com”使用