【单选题】
装设接地线应（ ），拆除接地线的顺序与此相反。___
A. 先接母线侧、后接负荷侧
B. 先接负荷侧、后接母线侧
C. 先接导体端、后接接地端；
D. 先接接地端、后接导体端
查看试卷，进入试卷练习
微信扫一扫，开始刷题
相关试题
【单选题】
电缆及电容器接地前应（ ）充分放电。___
A. 逐相
B. 保证一点
C. 单相
D. 三相
【单选题】
电缆及电容器接地前应逐相充分放电，星形接线电容器的中性点应接地，串联电容器及与整组电容器脱离的电容器应（ ）。___
A. 全部接地
B. 单只接地
C. 充分放电
D. 逐个充分放电
【单选题】
（ ）及电容器接地前应逐相充分放电。___
A. 避雷器
B. 电缆
C. 导线
D. 变压器
【单选题】
接地线截面积应满足装设地点短路电流的要求，且高压接地线的截面积不得小于（ ）mm2。___
【单选题】
成套接地线应由有（ ）的多股软铜线和专用线夹组成。___
A. 绝缘护套
B. 护套
C. 透明护套
D. 橡胶护套
【单选题】
低压接地线和个人保安线的截面积不得小于（ ）mm2。___
【单选题】
接地线应使用专用的线夹固定在导体上，禁止用（ ）的方法接地或短路。___
【单选题】
杆塔无接地引下线时，可采用截面积大于190mm2（如φ16mm圆钢）、地下深度大于（ ）m的临时接地体。___
A. 0.6
B. 0.8
C. 1.0
D. 1.2
【单选题】
若由于设备原因，接地刀闸与检修设备之间连有断路器（开关），在接地刀闸和断路器（开关）合上后，应有保证断路器（开关）不会（ ）的措施。___
【单选题】
在工作地点或检修的配电设备上悬挂（ ）标示牌；___
A. “在此工作！”
B. “从此进出！”
C. “禁止合闸，有人工作！”
D. “止步，高压危险！”
【单选题】
工作地点有可能误登、误碰的邻近带电设备，应根据设备运行环境悬挂（ ）等标示牌。___
A. “禁止攀登，高压危险！”
B. “在此工作！”
C. “止步，高压危险！”
D. “当心触电！”
【单选题】
配电线路、设备检修，在显示屏上断路器（开关）或（ ）的操作处应设置“禁止合闸，有人工作！”或“禁止合闸，线路有人工作！”以及“禁止分闸！”标记。___
A. 接地刀闸
B. 母线刀闸
C. 隔离开关（刀闸）
D. 保护压板
【单选题】
配电设备检修，若无法保证安全距离或因工作特殊需要，可用与带电部分直接接触的（ ）隔板代替临时遮栏。___
【单选题】
城区、（ ）或交通道口和通行道路上施工时，工作场所周围应装设遮栏（围栏），并在相应部位装设警告标示牌。___
A. 山区
B. 郊区
C. 有人区域
D. 人口密集区
【单选题】
单独巡视人员应经（ ）批准并公布。___
A. 公司领导
B. 工区领导
C. 工区
D. 安质部门
【单选题】
正常巡视应（ ）。___
A. 穿绝缘鞋
B. 穿纯棉工作服
C. 穿绝缘靴
D. 戴手套
【单选题】
夜间巡线应携带足够的（ ）。___
A. 干粮
B. 照明用具
C. 急救药品
D. 防身器材
【单选题】
灾害发生后，若需对配电线路、设备进行巡视，应得到（ ）批准。___
A. 设备运维管理单位领导
B. 设备运维管理单位
C. 工作负责人
D. 值班调控人员
【单选题】
巡视中发现高压配电线路、设备接地或高压导线、电缆断落地面、悬挂空中时，室内人员应距离故障点（ ）m以外。___
【单选题】
进入SF6配电装置室，应（ ）。___
A. 先检测
B. 先通风
C. 使用防护用品
D. 先散热
【单选题】
配电站、开闭所、箱式变电站等的钥匙至少应有（ ）。___
【单选题】
具备条件的设备可进行（ ）操作，即应用可编程计算机进行的自动化操作。___
【单选题】
检修人员操作的设备和接、发令程序及安全要求应由（ ）批准，并报相关部门和调度控制中心备案。___
A. 公司
B. 工区
C. 设备运维管理单位
D. 安质部
【单选题】
配电设备的防误操作闭锁装置不得随意退出运行，停用防误操作闭锁装置应经（ ）批准。___
A. 工区领导
B. 工作负责人
C. 公司
D. 工区
【单选题】
设备检修时，回路中所有（ ）刀闸的操作手柄，应加挂机械锁。___
A. 来电侧
B. 受电侧
C. 两侧
D. 负荷侧
【单选题】
停电拉闸操作应按照（ ）的顺序依次进行，送电合闸操作应按与上述相反的顺序进行。禁止带负荷拉合隔离开关（刀闸）。 ___
A. 断路器（开关）—负荷侧隔离开关（刀闸）—电源侧隔离开关（刀闸）
B. 负荷侧隔离开关（刀闸）——断路器（开关）——电源侧隔离开关（刀闸）
C. 断路器（开关）—电源侧隔离开关（刀闸）—负荷侧隔离开关（刀闸）
D. 负荷侧隔离开关（刀闸）——电源侧隔离开关（刀闸）——断路器（开关）
【单选题】
用间接方法判断操作后的设备位置时，至少应有两个（ ）指示发生对应变化，且所有这些确定的指示均已同时发生对应变化，方可确认该设备已操作到位。___
A. 非同样构造或非同源的
B. 同样原理或同源的
C. 非同样原理或非同源的
D. 非同样原理或非同期的
【单选题】
（ ）时，禁止就地倒闸操作和更换熔丝。___
【单选题】
装设柱上开关（包括柱上断路器、柱上负荷开关）的配电线路停电，应（ ）。送电操作顺序与此相反。___
A. 先断开柱上开关，后拉开隔离开关（刀闸）
B. 先拉开隔离开关（刀闸），后断开柱上开关
C. 先停主线开关，后停支线柱上开关
D. 先停支线柱上开关，后停主线开关
【单选题】
配电变压器停电，应（ ）。送电操作顺序与此相反。___
A. 先拉开高压侧熔断器，后拉开低压侧开关（刀闸）
B. 先拉开低压侧开关（刀闸），后拉开高压侧熔断器
C. 先拉开低压侧分路开关，后拉开低压侧总开关
D. 先拉开低压侧总开关，后拉开低压侧分路开关
【单选题】
摘挂跌落式熔断器的熔管，应使用（ ），并派人监护。___
A. 绝缘棒
B. 验电器
C. 操作杆
D. 专用工具
【单选题】
砍剪靠近带电线路的树木，（ ）应在工作开始前，向全体作业人员说明电力线路有电。___
A. 工作负责人
B. 工作许可人
C. 工作票签发人
D. 专业室领导
【单选题】
砍剪靠近带电线路的树木，工作负责人应在工作开始前，向全体作业人员说明电力线路有电；人员、树木、绳索应与导线保持10kV（ ）m规定的安全距离。___
A. 0.7
B. 1.0
C. 1.5
D. 3.0
【单选题】
为防止树木（树枝）倒落在线路上，应使用绝缘绳索将其拉向与线路（ ）的方向，绳索应有足够的长度和强度，以免拉绳的人员被倒落的树木砸伤。___
A. 相反
B. 60度
C. 90度
D. 相同
【单选题】
上树时，应使用安全带，安全带不得系在待砍剪树枝的（ ）附近或以上。不得攀抓脆弱和枯死的树枝；不得攀登已经锯过或砍过的未断树木。___
【单选题】
挖坑前,应与有关地下管道、电缆等设施的（ ）取得联系，明确地下设施的确切位置，做好防护措施。___
A. 主管单位
B. 运行单位
C. 维护单位
D. 建设单位
【单选题】
在超过（ ）m深的基坑内作业时，向坑外抛掷土石应防止土石回落坑内，并做好防止土层塌方的临边防护措施。 ___
【单选题】
不得站在（ ）传递土石或放置传土工具；禁止由下部掏挖土层。___
A. 挡板上
B. 撑木上
C. 挡板、撑木上
D. 脚手架上
【单选题】
在下水道、煤气管线、潮湿地、垃圾堆或有腐质物等附近挖坑时，应设（ ）。___
A. 工作负责人
B. 工作许可人
C. 监护人
D. 工作班成员
【单选题】
163.在下水道、煤气管线、潮湿地、垃圾堆或有腐质物等附近挖坑时，应设监护人。在挖深超过（ ）m的坑内工作时，应采取安全措施，如戴防毒面具、向坑中送风和持续检测等。___
推荐试题
【单选题】
In which type of attack does an attacker overwrite an entry in the CAM table to divert traffic destined to a legitimate host？___
A. DHCP spoofing
B. ARP spoofing
C. CAM table overflow
D. MAC spoofing
【多选题】
Which two attack types can be prevented with the impleme ntation of a Cisco IPS solution？___
A. DDos
B. man-in-the-middle
C. worms
D. ARP spoofing
E. VLAN hopping
【多选题】
choose four___
A. DHCP snooping ——————————blocks DHCP messages
B. Dynamic ARP inspection——————verifies IP-to-MAC traffic on untrusted ports
C. IP sources guard ——————————provides layer 2 interface security with ports ACLs
D. Port security————————————mitigates MAC-address spoofing at the access interface
【多选题】
choose four___
A. Step1————————run the system setup wizard
B. Step2————————add an authentication realm
C. Step3————————configure identity management
D. Step4————————configure directory group
【多选题】
What are two advanced features of the Cisco AMp solution for endpoints ___
A. contemplation
B. foresight
C. sandboxing
D. reputation
E. reflection
【多选题】
Which two characteristics of RADIUS are true？___
A. It encrypts only the password between user and server.
B. It uses TCP ports 1812/1813
C. It uses UDP ports 1812/1813.
D. It uses UDP port 49
E. It uses TCP port 49
【多选题】
What are two challenges of using a network-based IPS？ ___
A. It is unable to determine whether a detected attack was successful
B. It requires additional storage and proce ssor capacity on syslog servers
C. As the network expands， it requires you to add more sensors.
D. It is unable to detect attacks across the entire network
E. It must support multiple operating systems.
【多选题】
What are two default be haviors of the traffic on a zone-based firewall？___
A. Traffic within the self -zone uses an im plicit deny all.
B. All traffic between zones is implicitly blocked
C. Communication is allowed between interfadAss that are members of the same zone
D. Communication is blocked between interfaces that are members of the same zone
E. The CBAC rules that are configured on router interfaces apply to zone interfaces
【多选题】
Which two advantages does the on-premise model for MDM deployment have over the cloud-based model？___
A. The on-premise model is easier and faster to de ploy than the cloud-based model
B. The on-premise model is more scalable than the cloud-based model
C. The on-premise model is generally less expensive than the cloud-based model
D. The on-premise model generally has less latency than the cloud- based model.
E. The on-premise model provides more control of the MDM solution than the cloud
【多选题】
Which two actions can an end usts take to manage a lost or stolen device in Cisco ISE？ ___
A. Activate Cisco ISE End point Protection Services to quarantine the device.
B. Add the mac address of the device to a list of blacklisted devices
C. Force the device to be locked with a PIN
D. Request revocation of the digital certificate of the device.
E. Reinstate a device that the user previously marked as lost or stolen
【多选题】
Which two problems can arise when a proxy firewall serves as the gateway between networks？___
A. It can prevent content caching
B. It can limit application support
C. It is unable to prevent direct connections to other networks
D. It can cause reduced throughput.
E. It is unable to provide antivirus protection
【多选题】
When using the Adaptive Security Device Manager（ASDM）， which two methods are available to add a new root certificate？___
A. Use sCep
B. Install from SFTP server
C. Install from a file
D. Use Https
E. Use LDAP
【多选题】
Which two are considered basic security principles？___
A. Accountability
B. Redundancy
C. High Availabilit
D. Integrity
E. Confidentiality
【多选题】
Which two roles of the Cisco WSA are true？___
A. IPS
B. firewall
C. antispam
D. web proxy
E. URL filter
【单选题】
Which next-generation encryption algorithm supports four variants？___
A. SHA-2
B. SHA-1
C. MD5
D. HMAC
【单选题】
What aims to remove the abil ity to deny an action？___
A. Non-Repudiation
B. Accountability
C. Integrity
D. Deniability
【单选题】
Which statements about the native VLAN is true ？___
A. It is susceptible to VLAN hopping attacks.
B. It is the Cisco recommended VLAN for switch-management traffic
C. It is most secure when it is a ssigned to vLAn 1.
D. It is the cisco-recomme nded vlan for user traffic
【单选题】
There are two versions of IKE:IKEv1 and IKEv2. Both IKEv1 and IKEv2 protocols operate in phases IKEv1 operates in two phases. IKEv2 operates in how many phases？___
【单选题】
What does the dh group refer to？___
A. length of key for hashing C
B. length of key for encryption
C. tunnel lifetime key
D. length of key for key exchange
E. length of key for authentication
【单选题】
Which path do you follow to enable aaa through the SDM ？___
A. Configure Tasks > AAA
B. Configure > Addition Authentication > AAA
C. Configure > AAA
D. Configure > Additional Tasks > AAA
E. Configure Authentication > AAA
【单选题】
which technology cloud be used on top of an MPLS VPN to add confidentiality ？___
A. IPsec
B. 3DES
C. AES
D. SSL
【单选题】
Which term is most closely aligned with the basic purpose of a SIEM solution? ___
A. Non-Repudiation
B. Accountability
C. Causality
D. Repudiation
【单选题】
You have just deployed SNMPv3 in your environment， Your manager asks you to make sure that our SNMP agents can only talk to the SNMP Manager. What would you configure on your SNMI agents to satisfy this request？___
A. A SNMP View containing the SNMP managers
B. Routing Filter with the SNMP managers in it applied outbound
C. A standard ACL containing the SNMP managers applied to the SNMP configuration
D. A SNMP Group containing the SNMP managers
【单选题】
Which feature prevents loops by moving a nontrunking port into an errdisable state when a BPDU is received on that port？___
A. BPDU filte
B. DHCP snooping
C. BPDU guard
D. Port Fast
【单选题】
Which command enables port security to use sticky MAC addresses on a switch？___
A. switchport port-security violation restrict
B. switchport port-security mac-address sticky
C. switchport port-security violation protect
D. switchport port-security
【单选题】
When you edit an IPS subsignature， what is the effect on the parent signature and the family of subsignatures？___
A. The change applies to the parent signature and the entire family of subsignatures
B. The change applies to the parent signature and the subsignature that you edit
C. The change applies only to subsignatures that are numbered sequentially after the subsignature that you edit
D. Other signatures are unaffected， the change applies only to the subsignature that you dit
【单选题】
Which type of mechanism does Cisco FirePOWER de ploy to protect ag detected moving across other networks？___
A. antivirus scanning
B. policy-based
C. reputation-based
D. signature-based
【单选题】
What action must you take on the ise to blacklist a wired device？___
A. Locate the switch through which the device is connected and push an a cl restricting all access by the device
B. Issue a CoA request for the de vice's mac address to each access switch in the network
C. Revoke the device's certificate so it is unable to authenticate to the network
D. Add the device's MAc address to a list of black listed devices
【单选题】
Which type of firewall can perform deep packet inspection？___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing？___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication？___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning？___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5， but does not use encryption？___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist， using security intelligence to block illicit network activity. However， the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites？___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat（ins，any）dynamic interface】Which ty pe of NaT is configured on a Cisco ASA？___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network？___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration？___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS？___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security？___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
