相关试题
【单选题】
___不是影响焊接接头性能的因素。
A. 焊后热处理
B. 焊接工艺方法
C. 焊接工艺参数
D. 焊接位置
【单选题】
反变形法主要用来减小弯曲变形和___。
A. 收缩变形
B. 扭曲变形
C. 波浪变形
D. 角变形
【单选题】
火焰矫正焊接变形时,最高加热温度不宜超过___℃。
A. 1300
B. 1100
C. 900
D. 800
【单选题】
火焰矫正法适用于___构件矫正焊接变形。
A. 奥氏体不锈钢
B. 珠光体耐热钢
C. 16Mn
D. 中碳钢
【单选题】
对于___,焊后不必采取消除焊接应力的措施。
A. 塑性较差的高强钢焊接结构
B. 刚性拘束度大的厚壁压力容器结构
C. 存在较大的三向拉伸残余应力的结构
D. 低碳钢、16Mn等一般性焊接结构
【单选题】
___不是减小焊接应力的措施。
A. 采用合理的焊接顺序和方向
B. 采用较小的焊接线能量
C. 预热
D. 采用较大的焊接线能量
【单选题】
碳当量___时,钢的淬硬冷裂倾向不大, 焊接性优良。
A. 小于0.40%
B. 小于0.50%
C. 小于0.60%
D. 小于0.80%
【单选题】
___不属于低合金专用结构钢。
A. 耐蚀钢
B. 低合金低温钢
C. 珠光体耐 热 钢
D. 马氏体不锈钢
【单选题】
___不属于有淬硬冷裂倾向的低合金结构钢焊接工艺特点。
A. 采取预热
B. 要控制线能量(热输入)、
C. 采取降低含氢量的工艺措施
D. 采用酸性焊条
【单选题】
屈服点在___MPa以上的低合金结构钢焊接时一般需要预热。
A. 275
B. 295
C. 345
D. 390
【单选题】
低合金结构钢采取局部预热时,预热范围为焊缝两侧各不小于焊件厚度的3倍,且不小于___mm。
A. 300
B. 250
C. 200
D. 100
【单选题】
16Mn钢焊接时,焊条应选用___。
A. E4303
B. E4315
C. E5515—G
D. E5015
【单选题】
板厚16mm以下的16Mn钢焊接环境温度___℃以下预热100 ~ 150℃。
【单选题】
18MnMoNb钢的使用状态为___。
A. 正火加回火
B. 退火
C. 热轧
D. 热轧加回火
【单选题】
在高温、高压蒸汽的运行条件下,碳钢的最高工作温度为___℃。
A. 350
B. 450
C. 550
D. 650
【单选题】
___是珠光体耐热钢的主要合金元素。
A. Cr 和Ni
B. Cr和Mn
C. Mn和Mo
D. Cr和Mo
【单选题】
珠光体耐热钢焊前局部预热必须保证预热宽度焊缝两侧各大于所焊壁厚的4倍,且至少不小于___mm。
A. 50
B. 100
C. 150
D. 200
【单选题】
珠光体耐热钢焊条电弧焊焊后应立即进行___。
A. 中温回火
B. 低温回火
C. 退火
D. 高温回火
【单选题】
奥氏体不锈钢焊接是,如果焊接材料选用不当或焊接工艺不合理时会产生___等问题。
A. 接头软化和热裂纹
B. 降低接头抗晶间腐蚀能力和冷裂纹
C. 降低接头抗晶间腐蚀能力和再热裂纹
D. 降低接头抗晶间腐蚀能力和热裂纹
【单选题】
为了防止奥氏体不锈钢焊接热裂纹,希望焊缝金属组织是奥氏体—铁素体双相组织,其中铁素体的质量分数应控制在___左右 。
A. 30%
B. 20%
C. 10%
D. 5%
【单选题】
奥氏体不锈钢多层多道焊时,层间温度(即各焊道间温度)应低于___℃。
A. 350
B. 250
C. 150
D. 60
【单选题】
牌号为A137的焊条是___。
A. 碳钢焊条
B. 低合金钢焊条
C. 珠光体耐热钢焊条
D. 奥氏体不锈钢焊条
【单选题】
___不是奥氏体不锈钢焊条电弧焊工艺操作必须遵循的原则。
A. 采用小线能量,小电流短弧快速焊
B. 采用多层多道焊
C. 采用焊条摆动的窄道焊
D. 选用焊条碱性焊条,采用直流反接
【单选题】
___不是焊缝内部缺陷。
A. 未熔合
B. 未焊透
C. 夹渣
D. 焊瘤
【单选题】
工作表面锈皮未清除干净会引起___。
A. 气孔
B. 再热裂纹
C. 咬边
D. 弧坑
【单选题】
钨级直径太小、焊接电流太大是产生___的原因之一。
A. 冷裂纹
B. 热裂纹
C. 再热裂纹
D. 夹钨
【单选题】
在射线探伤胶片上呈一条断续的或连续的黑直线(其宽窄取决于对接焊缝坡门根部间隙的大小)缺陷是___。
A. 裂纹
B. 未熔合
C. 气孔
D. 未焊透
【单选题】
我国射线探伤标准规定,焊缝质量分为四个等级,3级焊缝内不允许有___。
A. 气孔
B. 夹渣
C. 夹钨
D. 加垫板单面焊的未焊透
【判断题】
在生产中焊工对焊工工艺文件可根据实际情况灵活执行
【判断题】
在910℃以下的面心立方晶格的铁称为γ-Fe
【判断题】
材料在外力作用下抵抗永久变形和断裂的能力称为强度
【判断题】
对电源中性点直接接地的低压电网中的用电器,可以把用电器的外壳接在中线上,叫保护接地
【判断题】
变压器是利用电磁感应原理工作,无论是升压或降压,变压器只能改变交流电的电压,而不能改变交流电的频率
【判断题】
由湿木板、钢筋混凝土、沥青、瓷砖、金属等材料铺设的地面也属于触电的危险环境
【判断题】
施焊前,焊工应对面罩进行安全检查,主要是耐腐蚀性能,隔热能力,反光性能,防毒性能等
【判断题】
钨极氩弧焊的钨极端部形状采用锥形尖端效果最好,电弧稳定,焊缝成形良好.
推荐试题
【单选题】
The standard altimeter setting is______inhpa. ___
A. 1013.20062
B. 1010.10062
C. 29.92002
D. 30.10002
【单选题】
2500f/m rate of vertical speed is equal to______.___
A. 10m/s
B. 15m/s
C. 20m/s
D. 25m/s
【单选题】
陆空通话时,什么时候推荐使用“IMMEDIATELY(立即)”这个词:___
A. 相对飞行穿高度时
B. 天气差时,担心自己会忘记某个正在改变高度的动态
C. 飞机多时,为了节省精力
D. 在紧急情况下,用于冲突解脱时
【单选题】
Standard rate for a turning is______degrees per second. ___
【单选题】
What is the best course of action for a pilot to follow when thunderstorms are observed along the route of flight? ___
A. Fly below the thunderstorms
B. Climb over the thunderstorms
C. Disregard the thunderstorms
D. Take any action to avoid all thunderstorms
【单选题】
The subdivision of frequencies is______MHZ. ___
A. 0.025
B. 0.035
C. 0.02
D. 0.015
【单选题】
Aeronautical chart is divided into two categories,______. ___
A. Aeronautical map and special type of aeronautical chart
B. En-route chart and approach chart
C. Area chart and standard instrument arrival and departure chart
D. Aerodrome chart and area chart
【单选题】
Aircraft are required to comply with ATC instructions within______.___
A. advisory airspace
B. domestic airspace
C. controlled airspace
D. international airspace
【单选题】
Amendments to the initial clearance will be issued at anytime an air traffic controller deems such action necessary to______.___
A. avoid possible confliction between aircraft
B. correct the previously issued clearance
C. cancel the flight plan
D. expedite the traffic
【单选题】
研究表明,当耳机话筒的位置距离嘴( )英寸且稍微偏下时,传输的声音质量最佳。(注:1英寸=2.54CM)___
A. 0.25-0.5
B. 0.75-1
C. 1.25-1.5
D. 1.75-2
【单选题】
“I want to divert to shanghai” is equal to______.___
A. I want to our destination Shanghai
B. I want to overfly Shanghai
C. I want to alternate to land at Shanghai
D. I want to call Shanghai control
【单选题】
When an aircraft is being subjected to unlawful interference, the pilot should try to notify _______ of this fact.___
A. the appropriate ATC units
B. company
C. the passengers on board
D. air attendants
【单选题】
When pilot say“Did you pick it upon your screen?”,that means______.___
A. did you pick up your screen?
B. did you see it on your screen?
C. did your screen pick me up?
D. did you change your radar?
【单选题】
ATC clearance does not contain______.___
A. clearance limit
B. altitude data
C. route of flight
D. flight direction
【单选题】
When pilot sets an altimeter setting to a QNH,that will indicate_________
A. flight level
B. altitude
C. height
D. safety level
【单选题】
When pilots set a pressure of 29.92 in mercury to indicate_________
A. altitude
B. height
C. flight level
D. safety level
【单选题】
管制员还应当对管制指令当中的不同内容进行适当的排序,相对重要的内容应当排列在管制指令的 ( )位置___
A. 前面
B. 中间
C. 尾部
D. 以上都可以
【单选题】
When Beijing time is 0801,Zulu time should be______.___
A. 2001
B. 1
C. 601
D. 1601
【单选题】
Emergency frequency is______.___
A. 121.5MHZ
B. 120.5MHZ
C. 121MHZ
D. 119.0MHZ
【单选题】
“PAN” is the international RTF______signal___
A. emergency
B. distress
C. urgency
D. dangerous
【单选题】
“MAYDAY” is the international RTF______signal.___
A. emergency
B. distress
C. urgency
D. dangerous
【单选题】
According to ICAO definition, a condition concerning the safety of an aircraft or other vehicle or of some person on board or within sight but which does not require immediate assistance is _______ .___
A. urgency
B. dangerous
C. emergency
D. distress
【单选题】
Which SSR Code is not right?___
A. 7020
B. 8025
C. 6060
D. 4021
【单选题】
______is the accepted standard for worldwide time signal broadcast used for aviation.___
A. GMT
B. LT
C. UTC
D. SST
【单选题】
_____means the level is measured in 1013.2 pha___
A. Level
B. Height
C. Altitude
D. Flight level
【单选题】
An aircraft known or believed to be in a state of emergency should be given______over other aircraft.___
A. way
B. flight plan
C. instruction
D. priority
【单选题】
管制话筒正确使用方法是:___
A. PTT发射键还没有完全按下时就开始发指令
B. 指令还没有结束就松开PTT发射键
C. 按PTT发射键与发话同时进行,松开PTT发射键与发话同时进行
D. 先按下话筒PTT发射键,然后再开始对空发话,发话完毕后再松开话筒PTT发射键
【单选题】
SSR code is a______digital number.___
A. two
B. six
C. one
D. four
【单选题】
Traffic information should include_________
A. direction of aircraft concerned
B. weather
C. speed of aircraft
D. heading of aircraft
【单选题】
根据区管中心业务通告,管制员通知机组转换频率的管制指令应当与其他管制指令( )。___
【单选题】
20NM is equal to.___
A. 40km
B. 38km
C. 37km
D. 41km
【单选题】
The altimeter setting used in en-route flight should be______hpa___
A. 1019
B. 1013
C. 2992
D. 1000
【单选题】
Larger separations than the specified minima should be applied whenever in.___
A. turbulence
B. bad weather
C. a raining day
D. highlevel
【单选题】
_______is air traffic control service for controlled flights in control areas___
A. Route service
B. En-route fly service
C. Area control service
D. Deviation control service
【单选题】
_______ is a service provided to notify appropriate organizations regarding aircraft in need of search and rescue aid, and assist such organizations as required.___
A. alerting service
B. information service
C. rescue service
D. assistance service
【单选题】
Visibility is the ability as determined by atmospheric conditions and expressed in unit______.___
A. meters
B. feet
C. distance
D. odometer
【单选题】
SIGMET is a weather advisory issued concerning weather______to the safety of all aircraft.___
A. significant
B. changeable
C. information
D. condition
【单选题】
Flight level is a______of constant atmospheric pressure which is related to a specific pressure datum 1013.2hpa.___
A. standard
B. surface
C. height
D. number
【单选题】
Air traffic means all aircraft in flight or operating on the______of an aerodrome.___
A. highway
B. hanger
C. maneuvering area
D. terminal
【单选题】
The true airspeed is the airspeed of an aircraft relative to______air.___
A. turbulence
B. smooth
C. undisturbed
D. the