相关试题
【多选题】
跌落式熔断器的主要技术参数有。___
A. 额定电压
B. 额定电流
C. 开断能力
D. 额定容量
【多选题】
现场对大用户抄表必须在、严格把关。应最大需量表。___
A. 在时间上
B. 抄表质量上
C. 自行抄录
D. 与用户共同抄录
【多选题】
电伤的种类有。___
A. 电灼伤
B. 电击伤
C. 电烙印
D. 皮肤金属化
【多选题】
供电方式主要内容包括两部分。___
A. 确定供电线路回路数
B. 确定供电电源
C. 选择供电线路
D. 确定用电容量
【多选题】
一个进户点供一个用户使用时,只装一组即可。___
A. 配电盘面
B. 电能表
C. 开关
D. 熔体盒
【多选题】
以下哪几项属于高压断路器的技术参数。___
A. 额定电压
B. 额定功率
C. 额定短路开断电流
D. 额定峰值耐受电流
【多选题】
按照结构和使用材料分,并联电容器可分为类型。___
A. 浸渍剂型
B. 金属化膜型
C. 密集型
D. 并联补偿成套装置
【多选题】
下列关于“网孔电流法”说法正确的是。___
A. 在网孔中环行的假想电流,叫做网孔电流
B. 支路电流是网孔电流叠加而成的
C. 支路电流就是网孔电流
D. 网孔电流法是用支路电流作为未知量列方程分析电路的
【多选题】
现场施工完毕后应核对集中器、采集器等信息,确保现场信息与工作单一致。___
A. 编号
B. 型号
C. 安装地址
D. 户号
【多选题】
架空配电线路的绝缘子通常有。___
A. 针式绝缘子
B. 蝶式绝缘子
C. 棒式绝缘子
D. 悬式绝缘子
【多选题】
在纯电容电路中,电压与电流的关系是。___
A. 纯电容电流的电压与电流频率相同
B. 电流的相位超前于外加电压u为π/2(即90°)
C. 电压与电流有效值的关系也具有欧姆定律的形式
D. 电流的相位滞后于外加电压u为π/2(即90°)
【多选题】
当电动机绕组发生时,会引起绕组发热,绝缘损坏而燃烧起火。___
A. 电源短路
B. 单相匝间短路
C. 单相接地
D. 相间短路
【多选题】
基础坑开挖遇到地下水位高,土质不良(如流砂及松散易塌方的土质)时,应采取的措施和方法有。___
A. 增大坑口尺寸,并在挖至要求深度以后,立即进行立杆
B. 当杆坑较深时采用增大坑口尺寸,可用围栏或板桩撑住坑壁
C. 杆坑应在放置电杆侧挖马道,拉线坑也要在拉线侧挖出马道
D. 坑深检查,带坡度拉线坑检查以坑中心为准
【多选题】
引起电缆终端盒火灾的原因有。___
A. 终端盒绝缘受潮、腐蚀、绝缘被击穿
B. 过负荷
C. 充油电缆由于安装高度差不合要求,内中压力过大使终端盒密封破坏,引起漏油起火
D. 电缆通过短路电流,使终端盒绝缘炸裂
【多选题】
验电的三个步骤为。___
A. 检查各部分螺丝是否紧固
B. 验电前应将验电笔在带电的设备上验电,证实验电笔是否良好
C. 在设备进出线两侧逐相进行验电,不能只验一相
D. 验明无电压后再把验电笔在带电设备上复核是否良好
【多选题】
直接接触触电的防护措施有、安全距离防护和采用漏电保护装置。___
A. 绝缘防护
B. 屏护防护
C. 障碍防护
D. 接触防护
【多选题】
关于“无功”和“无功功率”说法正确的是。___
A. 能够在磁场中储存
B. 在电源与负载之间进行往复交换而不消耗的能量
C. 单位时间内的无功交换量叫无功功率
D. 在电路中进行能量交换的功率叫无功功率
【多选题】
线路绝缘子主要分为针式绝缘子、蝶式绝缘子、悬式绝缘子、等多种类型。___
A. 悬式绝缘子
B. 瓷横担
C. 瓷拉棒
D. 拉线绝缘子
【多选题】
电容器运行时的巡视检查内容有___
A. 检查瓷件有无闪络、裂纹、破损和严重脏污,外壳有无鼓肚、锈蚀
B. 检查接地是否良好
C. 检查开关、熔断器是否正常、完好,并联电容器的单台熔丝是否熔断
D. 检查自动投切装置动作是否正确
【多选题】
正常巡视线路时对电杆应检查的内容。___
A. 有无斜歪
B. 基础下沉
C. 裂纹及露筋情况
D. 线路名称及杆号
【多选题】
调整导线弧垂的方法是。___
A. 调整导线弧垂时,操作人员在耐张杆或终端杆上,利用三角紧线器(也可与双钩紧线器配合使用)调整导线的松紧
B. 若为多档耐张段,卡好紧线器后,即可解开架线杆上导线的绑线,并选择耐张段中部有代表性的档距观测弧垂
C. 若三相导线的弧垂均需调整,则应先同时调整好两个边相,然后调整中相,调整后的三相导线弧垂应一致
D. 在终端杆上对导线弧垂进行调整时,应在横担两端导线反方向做好临时拉线,防止横担因受力不均而偏转
【多选题】
供电方案的主要内容是确定等。___
A. 计量方案
B. 客户接入系统方案
C. 客户受电系统方案
D. 计费方案
【多选题】
下列对绝缘电阻的测量方法和注意事项描述,正确的是。___
A. 引线必须使用绝缘良好的单根多股软线
B. 开路时指针是否指在“0”位,短路时指针是否指在“∞”位
C. 应由两人操作,保持与带电体的安全距离
D. 设备电容较大时,必须在额定转速状态下方可将测电笔接触或离开被测设备
【多选题】
并联电容器的主要作用有。___
A. 补偿无功功率
B. 补偿有功功率
C. 提高功率因数
D. 降低功率因数
【多选题】
用电信息采集终端主要用于。___
A. 电能表数据的采集
B. 电能表数据管理
C. 电能表与终端数据双向传输
D. 转发或执行控制命令
【多选题】
集中抄表终端的竣工验收时,工作班成员的作业内容包含。___
A. 检查终端安装资料应正确、完备
B. 确认安装工艺质量应符合有关标准要求
C. 检查集中器是否满足送电要求
D. 检查接线应与竣工图一致
【多选题】
下列关于电容电抗的说法正确的是。___
A. 在交流电路中,由于电容器周期性的充电和放电,电容器两极上建立的电压极性与电源电压极性总是相同的,因此电容器极板上的电压相当于反电动势,对电路中的电流具有阻碍作用,这种阻碍电流作用称为电容电抗,简称容抗
B. 交流电的频率越高,容抗越大
C. 直流越不易通过电容
D. 交流容易通过电容
【多选题】
带电灭火可以使用、四氯化碳灭火器等。___
A. 二氧化碳灭火器
B. 水
C. 1211灭火器
D. 干粉灭火器
【多选题】
并联电路具有的特点是。___
A. 各电阻两端间的电压相等
B. 总电流等于各支路电流之和
C. 电路的总电阻的倒数等于各支路电阻倒数之和
D. 各电阻上流过的电流相等
【多选题】
客户的供电电压等级应根据,经过技术经济比较后确定。___
A. 当地电网条件
B. 客户分级
C. 用电最大需量或受电设备总容量
D. 用电性质
【多选题】
在一个抄表段内要明确的内容有。___
A. 抄表例日
B. 抄表周期
C. 抄表方式
D. 抄表时间
【多选题】
开关站运行人员巡视检查时,对互感器应做检查。___
A. 互感器整体无发热现象,表面无裂纹
B. 无异常的电磁声
C. 高、低压熔丝接触良好,无跳火现象
D. 电流回路无开路,电压回路无短路
【多选题】
氧化锌避雷器具有结构简单等特点。___
A. 保护特性好
B. 吸收过电压能量大
C. 保护特性一般
D. 吸收过电流容量大
【多选题】
常用低压熔断器一般由组成。___
A. 金属熔体
B. 连接熔体的触头装置
C. 绝缘子
D. 外壳
【多选题】
接户线的防雷措施有。___
A. 将接户线入户前的电杆瓷绝缘子脚接地
B. 将接户线零线接地
C. 安装低压避雷器
D. 在室内安装电能表常用的低压避雷器保护
【多选题】
《国家电网公司电费抄核收管理规则》规定,对的客户,其业务流程处理完毕后的首次电量电费计算,应逐户进行审核。___
A. 高压客户
B. 新装用电客户
C. 用电变更客户
D. 电能计量装置参数变化
【多选题】
接地装置的检查项目有。___
A. 接地引线有无破损及腐蚀现象
B. 接地体的接地圆钢、扁钢有无露出、被盗、浅埋等现象
C. 在土壤电阻率最大时测量接地装置的接地电阻,并对测量结果进行分析比较
D. 电气设备检修后,应检查接地线连接情况是否牢固可靠
【多选题】
护套线线路优点是适用于户内外,具有,以及造价较低等优点,因此在照明电路上已获得广泛应用。护套线线路缺点是导线截面小,大容量电路不能采用。___
A. 耐潮性能好
B. 抗腐蚀力强
C. 方便布置
D. 线路整齐美观
【多选题】
插座安装的具体要求是。___
A. 明装插座安装在木台上
B. 单相两孔插座两孔平列安装:左侧孔接零线,右侧孔接火线,即“左零右火原则”
C. 单相三孔插座安装时:必须把接地孔眼(大孔)装在上方,同时规定接地线桩必须与接地线连接,即“左零右火上接地”
D. 三相四孔插座上孔接地,右孔接L1,下孔接L2,左孔接L3
【多选题】
对一次电气设备起保护作用的辅助设备是二次设备,包括部分。___
A. 监测
B. 测量
C. 控制
D. 操作电源系统
推荐试题
【单选题】
An administrator is troubleshooting network communications between a vCenter Server and an ESXi 6.5 host. Which log shows the related events between these components?___
A. /var/log/fdm.log
B. /var/log/vpxa.log
C. /var/log/hostd.log
D. /var/log/auth.log
【单选题】
An administrator has recently upgraded from vSphere 6.0 to 6.5, and can no longer see the software iSCSI named vmhba33. Which could be the reason for this?___
A. The upgrade has changed the vmhba name.
B. vSphere 6.5 automates iSCSI configurations.
C. vSphere 6.5 no longer supports software iSCSI.
D. The upgrade has deleted the vmhba.
【单选题】
An administrator is trying to vMotion a VM from his datacenter to a recovery site. Which is the maximum allowed RTT (Round-Trip Time) latency between source and destination host?___
A. 100 milliseconds
B. 150 milliseconds
C. 15 milliseconds
D. 10 milliseconds
【单选题】
Which is required for configuring iSCSI Software Adapter network port binding?___
A. VMkernel of the iSCSI traffic must be load balanced using Route based on IP Hash algorithm.
B. VMkernel of the iSCSI traffic must be load balanced using Route based on Source Virtual Port ID algorithm.
C. VMkernel of the iSCSI traffic must be load balanced using Route based on Source MAC Hash algorithm.
D. VMkernel of the iSCSI traffic must be bound to only one active network adapter.
【单选题】
In vSphere Data Protection 6.1, which is the function of a Backup Verification job?___
A. None. Backup Verification job is not a feature of vSphere Data Protection
B. It is a manual task -Power it on -Verify the guest OS -Check started applications
C. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OS is booted by communicating with the Backup Verification agent
D. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OC is booted by detecting the VMware ToolsTM "heartbeats"
【单选题】
An administrator has enabled vSphere Distributed Switch Health Check. The hosts connected to that Distributed Switch all display an alert:< vSphere Distributed Switch MTU supported status > .The administrator has all of the VMkernel ports MTU sizes set to 1600. Which action will remedy this problem?___
A. Configure the Distributed Switch to MTU 9100.
B. Disconnect and reconnect the physical network cable.
C. Configure the physical switch to MTU 1600.
D. Disable the Distributed Switch MTU.
【单选题】
Which Host Profile Subprofile configuration is used to configure firewall settings for ESXi hosts?___
A. Advanced Configuration Settings
B. General System Settings
C. Security
D. Networking
【单选题】
Where would a vSphere administrator find general vCenter Server logs on a vCenter Server Appliance?___
A. /var/log/vmware/vpxd/
B. /var/log/messages
C. /etc/vmware-vpx/
D. /var/log/vmware/vsan-health/
【单选题】
An administrator wishes to enable network port mirroring based on source port. Which feature should be enabled?___
A. vSphere standard switch port
B. ERSPAN
C. NSX Virtual Wire
D. VLAN
【单选题】
Which CLI command shows the physical uplink status for a vmnic?___
A. esxcli network ip connection list
B. esxcli network ip neighbor list
C. esxcli network nic get
D. esxcli network nic list
【单选题】
Which is the maximum number of block devices (LUNs) that are supported by ESXi hosts that are running version 6.5?___
A. 1024
B. 512
C. 2048
D. 256
【单选题】
When performing a vCenter Server 5.5 for Windows with Microsoft SQL Server Express database migration to vCenter Server Appliance 6.5, which will be the target database?___
A. Microsoft SQL Server Express 2012R2
B. Microsoft SQL Server Standard 2012R2
C. PostgreSQL
D. Oracle DB 11g
【单选题】
An administrator has multiple vCenter Server 6.5 systems but cannot enable Storage I/O Control (SIOC) on a datastore shared by ESXi hosts managed by the vCenter Server systems. Which action should the administrator take to resolve the issue?___
A. Unmount the datastore and then enable SIOC on the vCenter Server system.
B. Configure the datastore to be managed by a single vCenter Server system.
C. Configure Storage DRS and then enable SIOC on the vCenter Server system.
D. Enable Raw Device Mapping (RDM) on the
E. SXi hosts.
【单选题】
“OneAppServer” is a VM template stored in a content library named “LibraryOne”, but the vSphere administrator is not able to use this template for deployment. Why is the administrator unable to deploy OneAppServer?___
A. OneAppServer must be updated before it can be deployed.
B. LibraryOne is a subscribed library and OneAppServer is not downloaded yet.
C. LibraryOne is published and optimized for syncing over HTTP.
D. OneAppServer was imported from a local file on the system.
【单选题】
An administrator sets the Failover Capacity for both CPU and Memory at 25%. Based on the Exhibit below, how much of the cluster’s total CPU resources are still available to power on additional virtual machines?___
A. 45%
B. 25%
C. 70%
D. 60%
【单选题】
Which statement applies to the vSphere Replication appliance?___
A. Only one vSphere Replication appliance can be deployed per vCenter Server instance.
B. VMware Tools in the vSphere Replication appliance can be upgraded.
C. A single vSphere Replication appliance can manage a maximum of 4000 replications.
D. vSphere Replication is available only with the vSphere
E. ssentials Plus license.
【单选题】
Which esxcli namespace can a vSphere Administrator use to adjust the queue depth?___
A. esxcli system module parameters
B. esxcli storage core device
C. esxcli system module set
D. esxcli storage core adapter
【单选题】
Which statement regarding datastore clusters meets VMware’s recommended best practices?___
A. Clusters should contain only datastores presented from the same storage array.
B. Clusters should contain only datastores with equal hardware acceleration capability.
C. Clusters should contain only datastores with the same capacity.
D. Clusters should contain only datastores using the same connection method (iSCSI, FC, etc.).
【单选题】
What VM Monitoring setting would ensure that the maximum reset window for a virtual machine is 24 hours?___
A. Medium
B. Low
C. High
D. Normal
【单选题】
What is the default space threshold for vSphere Storage DRS?___
A. 80%
B. 70%
C. 90%
D. 95%
【单选题】
Which is the correct sequence to upgrade a vSphere infrastructure?___
A. vCenter Server>ESXi host> VMware Tools>VM compatibility
B. ESXi host>vCenter Server> VMware Tools>VM compatibility
C. vCenter host> ESXi host> VM compatibility> VMware Tools
D. ESXi host>vCenter Server> VM compatibility>VMware Tools
【单选题】
An administrator has a large boot from SAN cluster and wants to ensure consistent configuration by using host profiles. What special considerations are required for boot from SAN hosts?___
A. Change the “Device is shared clusterwide” setting to “false” in the host profile.
B. Verify that the boot LUN is correctly identified as the boot device in the host profile.
C. The boot from SAN device must report as a local device.
D. Host profiles are incompatible with boot from SAN hosts.
【单选题】
When using VMware Converter to import a Windows server and improve the consistency of the destination virtual machine, which optional step can be performed immediately prior to powering down the source server?___
A. Perform a final synchronization task.
B. Remove the server from the network.
C. Uninstall production applications.
D. Remove the server from the Active Directory domain.
【单选题】
Restoration of the vCenter Server Appliance is accomplished using which interface?___
A. vSphere Web Client
B. vSphere Client
C. vCenter Server Appliance Management Interface
D. vCenter Server Appliance GUI Installer
【单选题】
When attempting to migrate a virtual machine to another host in the same cluster, the error message, “Select a valid compute resource” returns. What could cause this error?___
A. Both hosts run different versions of ESXi.
B. Both hosts are not sharing the same datastore.
C. VMware Tools is not installed.
D. Virtual machine has an ISO attached.
【单选题】
When will vSphere Data Protection delete the expired backup image of a Platform Service Controller?___
A. Immediately after the retention period has expired.
B. After the expired backup image is restored.
C. During the next backup window following expiry.
D. During the next maintenance window following expiry.
【单选题】
Group A has permission to download files in Content Library. Group B does not have permission to download files in Content Library. If a user is a member of both groups, what will be the result?___
A. The user cannot download file from Content Library.
B. The user can download file from Content Library.
C. The user cannot access Content Library.
D. The user can access Content Library.
【单选题】
An administrator is trying to set up Host Partial Failure Response, but the Automated option is grayed out. What can the administrator change to enable the Automated option?___
A. Change the vSphere DRS Automation level to Partially Automated.
B. Change the vSphere DRS Automation level to Fully Automated.
C. Enable vSphere HA Host Monitoring.
D. Change the vSphere DPM Automation level to Automatic.
【单选题】
When you attempt to open a virtual machine console from the vSphere Web Client, the console does not connect. The following error message appears:<HTTP ERROR 404> <Problem accessin/.Reason: Not Found>. Why did not connect?___
A. Port 443 is in use.
B. Port 9443 is in use.
C. Port 8443 is in use.
D. Port 22443 is in use.
【单选题】
What new feature was introduced to the Content Library in vSphere 6.5?___
A. Mount an ISO directly from the Content Library.
B. Deploy a virtual machine from an OVF Package in a Content Library.
C. Upload a File from a URL to a Library Item.
D. Upload a File from a Local System to a Library Item.
【单选题】
How can an administrator exclude Encryption rights from a support engineer?___
A. Clone the role Virtual machine power user, remove Cryptographic operations privileges.
B. Clone the role Administrator and assign to the support engineer.
C. Clone the role Virtual machine power user and assign to the support engineer.
D. Clone the role No cryptography administrator and select privileges only for the support engineer.
【单选题】
The administrator must back up a vCenter HA deployment. Which component must be backed up?___
A. Passive node
B. Witness node
C. External database
D. Active node
【单选题】
What is the supported protocol to perform remote L3 traffic monitoring in vSphere 6.5?___
A. VXLAN
B. ERSPAN
C. RSPAN
D. SPAN
【单选题】
What are the minimum hardware requirements for a Windows vCenter Server with embedded PSC that manages a “Small” environment?___
A. 2vCPUs, 16 GB RAM
B. 4 vCPUs, 16 GB RAM
C. 2 vCPUs, 10 GB RAM
D. 4 vCPUs, 10 GB RAM
【单选题】
Which port is used for communication between ESXi and vSphere Data protection?___
A. 80
B. 443
C. 902
D. 22
【单选题】
What can prevent Storage DRS from functioning on a datastore?___
A. The datastore is configured for Virtual Machine Swapfile location.
B. The datastore is shared across multiple datacenters.
C. The datastore is connected to a host that is running Storage I/O Control.
D. Storage DRS advanced option IgnoreAffinityRulesForMaintenance is set to 1.
【单选题】
When troubleshooting VMware vCenter Server issues, when logging level provides maximum detail?___
A. Verbose
B. Trivia
C. Info
D. Error
【单选题】
What new feature is introduced in NFS 4.1 on ESXi 6.5?___
A. IPv6
B. KRB5i
C. AUTH_SYS
D. Storage DRS
【单选题】
What configuration option would ensure that a virtual NUMA topology is defined on VMs having more than eight virtual CPUs?___
A. cupid.coresPerSocket
B. numa.vcpu.followcorespersocket
C. numa.vcpu.maxPerVirtualNode
D. numa.vcpu.min
【单选题】
What is the minimum disk space required to deploy vSphere Data Protection (VDP) with 8 TB configuration?___
A. 4 TB
B. 16 TB
C. 8 TB
D. 12 TB