相关试题
【单选题】
以下对地铁列车车体功能描述不正确的是___
A. 传递纵向力
B. 传递横向力
C. 应具有足够的强度和刚度要求
D. 传递垂向力
【单选题】
长沙地铁2号线风源系统工作压力范围为___。
A. 0-10.5bar
B. 0-12.5bar
C. 7-9bar
D. 3-4bar
【单选题】
BCU气路的主要功能是___。
A. 控制停放制动的施加
B. 控制停放制动的缓解
C. 形成并调整预控压力，实现对单元制动缸的充风
D. 形成并调整预控压力，实现对停放制动缸的充风
【单选题】
系统在每节车厢提供___台乘客紧急报警器（PECU）用于车厢内出现紧急情况时乘客向司机室报警。
【单选题】
下面关于广播的说法错误的是___
A. 当列车发生意外特殊情况，系统无法判断广播主控单元可能发生故障时，此时激活人工广播可无视优先级限制。
B. PIS系统主机提供OCC广播接口，当有OCC广播到来的时候，自动播放OCC广播。
C. 人工广播采用动圈对讲机麦克风，在讲话时需要按压PTT按键。
D. 人工广播可在非激活端司机室进行。
【单选题】
下面关于广播优先级（由高到低）的说法正确的是___
A. OCC广播>人工广播>紧急广播>报站广播
B. OCC广播>紧急广播>人工广播>报站广播
C. 紧急广播>人工广播>OCC广播>报站广播
D. 紧急广播>OCC广播>人工广播>报站广播
【单选题】
蓄电池充电机基本特点中，当蓄电池充电机无法正常启动时，应具有___功能。
A. 快速启动
B. 慢速启动
C. 强制启动
D. 紧急启动
【单选题】
牵引系统中网压额定最高限值为___V。
A. 2100
B. 1950
C. 1850
D. 1500
【多选题】
紧急制动不能缓解___。
A. 检查列车是否升弓
B. 检查两端司机室的紧急制动按钮是否按下
C. 检查微动开关22-F101是否跳闸
D. 尝试使用ATP切除模式，观察紧急制动是否缓解
【多选题】
列车产生紧急制动的原因有哪些___。
A. 紧剔按钮松开3s以上
B. 紧急按钮被按下
C. 单个HSCB跳闸
D. 方向手柄回零位
【多选题】
关于常用制动，下列说法正确的有___。
A. 常用制动是可恢复的制动
B. 常用制动是不可恢复的制动
C. 常用制动为电-空混合制动
D. 常用制动为电制动
【多选题】
查看司机室双针压力表，可以了解___。
A. 动车单元制动缸的压力
B. 拖车单元制动缸的压力
C. 动车停放制动缸的压力
D. 拖车停放制动缸的压力
E. 拖车主风管压力
【多选题】
快速制动时，由___调整预控压力。
A. 紧急制动电磁阀
B. 电子中继阀
C. 变载荷阀
D. 压力开关
【多选题】
下列原因可能会导致弓网故障的是___。
A. 路基引起受电弓运行线偏离原运行中心线
B. 接触网位移
C. 接触网网压为零
D. 受电弓变形及弓头维修指标不合要求
E. 外界因素，如风速大、接触网有异物
【多选题】
TCMS在以下情况下进行限速检测：___。
A. 当2个DCU故障TCMS进行60km/h限速检测
B. 当切除3节车以上制动，TCMS进行35km/h限速检测
C. 当退行时，TCMS进行10km/h限速检测
D. 当慢行模式时，TCMS进行3km/h限速检测
【多选题】
长沙地铁车辆采用了先进的微机控制技术，并具有故障自诊断功能。如___均采用了微机控制技术。
A. 牵引控制单元
B. 辅助逆变器控制单元
C. 电子制动控制单元
D. 空调控制单元
E. 车门控制单元
【多选题】
空调机组发生不制冷的原因有___。
A. 冷凝风机不工作
B. 继电器卡滞
C. 压缩机不工作
D. 送风机故障
【多选题】
空调机组产生高压保护的原因有___。
A. 冷凝器散热效果不良
B. 热力膨胀阀被堵塞
C. 高压侧毛细管堵塞
D. 系统充注制冷剂过量
【多选题】
空调机组产生低压保护的原因有___。
A. 系统中制冷剂量不足
B. 热力膨胀阀被堵塞
C. 冷凝风机不工作
D. 低压毛细管堵塞
【多选题】
引起蒸发器表面结霜的原因有___。
A. 系统中制冷剂量不足
B. 热力膨胀阀被堵塞
C. 干燥过滤干燥器被堵塞
D. 毛细管堵塞
【多选题】
可以使空调系统压缩机停止工作的原因有___。
A. 管路高压阀或低压阀动作
B. 控制压缩机启停的继电器损坏
C. 管路无制冷剂
D. 送风机故障
【多选题】
整列车气制动不能缓解故障处理方法有___。
A. 按压=73-S105
B. 查看HMI故障信息
C. 找出相应车制动故障切除B05
D. 合=27-S104
【多选题】
在长沙地铁2号线车辆中关于HMI功能描述正确的___。
A. 显示车辆故障信息
B. 能自动调节亮度
C. 工作额定输入电压DC110V
D. 自带蜂鸣器
【多选题】
接触网停电会导致车辆___
A. 紧制
B. 失去牵引力
C. 惰行
D. HMI上显示网压读数逐渐下降至0V
【多选题】
列车视频监视系统主要包含哪些功能___
A. 视频监控存储
B. 视频监控显示
C. 视频监控联
D. 多媒体播放系统
【多选题】
紧急制动的制动缓解施加方式，下列说法正确的是___
A. 失电制动
B. 失电缓解
C. 得电缓解
D. 得电制动
【多选题】
在长沙地铁2号线一期车辆中关于主风缸压力控制功能的说法正确的为___。
A. 空压机主风管压力降到7BAR后将启动两台空压机
B. 空压机主风管压力降到7.5BAR后将启动当日工作为主的空压机
C. 空压机主风管压力降到6BAR后将启动激活单元车组的空压机
D. 空压机主风管压力升到9BAR后将自动停止空压机打风
E. 空压机主风管压力升到10BAR后将自动停止空压机打风
【多选题】
车辆车门开启的先前条件有___
A. 车门开启允许信号
B. 零速信号
C. 开门信号
D. 牵引信号
【多选题】
可供选择的开关门模式有___
A. 自动
B. 半自动
C. 手动
D. 半联动
【多选题】
PIS系统中，RS485故障可能影响___功能。
A. 乘客报警
B. 广播报站
C. 紧急报站
D. LED显示
【多选题】
车门橙色指示灯什么情况下保持常亮。___
A. 车门处于打开位置
B. 开门过程中
C. 车门处于紧急操作状态下
D. 门关好
【判断题】
NRM模式下，从开门后动车开始运行60m内，车门紧急解锁导致列车紧急制动；运行距离超过60m，车门紧急解锁不影响列车正常牵引。
【判断题】
列车进入制动工况时，再生制动优先施加。
【判断题】
在紧急牵引模式下，车辆的牵引/制动指令是通过硬导线来传递的。
【判断题】
空调机组管路中设置毛细管的作用是监测管路压力。
【判断题】
空调机组在发生高压保护时，压缩机将继续工作。
【判断题】
运行中两个DC/DC无论是轻微、中级、严重故障，都可继续运营。
【判断题】
在牵引过程中松开警惕按钮，牵引指令立刻中断，列车出现紧急制动。
推荐试题
【单选题】
Which is the correct order for upgrading vSphere components?___
A. vCenter Server, ESXi hosts, VMware Tools, Virtual Machine hardware
B. VMware Tools, Virtual Machine hardware, ESXi hosts, vCenter Server
C. vCenter Server, Virtual Machine hardware, VMware tools, ESXi hosts
D. ESXi hosts, vCenter Server, Virtual Machine hardware, VMware Tools
【单选题】
Which iSCSI initiator type can be used with any network interface card?___
A. Software iSCSI initiator
B. Software FCoE adapter
C. Hardware Independent iSCSI initiator
D. Hardware Dependent iSCSI initiator
【单选题】
An administrator is attempting to power on a virtual machine with 32GB of memory. The operation fails with the following error: <Could not power on VM: No space left on device> <Checking the space on the virtual machine's datastore, there is 30GB free.> Which action would allow the VM to power on?___
A. Set a 2GB memory reservation on the VM.
B. Mount the virtual disk from the affected VM on to another virtual machine and free up space from within the OS.
C. Enable vSphere HD admission control on the cluster in which the VM resides.
D. Set a 2GB memory limit on the VM.
【单选题】
An administrator attempts to manually reclaim space on thin-provisioned VMFS6 volumes but finds that no additional space is being recovered. Which could be causing this?___
A. vSphere 6.5 does not support manual UNMAP.
B. The manual UNMAP operation has been moved to the vSphere web client.
C. The VASA version is use is incompatible.
D. UNMAP is automated for VMFS6.
【单选题】
An administrator has upgraded to vSphere 6.5 and also wants to use Kerberos authentication for NFS. Which can be done to the existing NFSv3 volumes to enable this feature?___
A. Perform a storage rescan on VMFS volumes.
B. Unmount the NFSv3 datastore, and then mount as NFSv4.1 datastore.
C. Nothing. All NFSv3 mounted datastores are upgraded automatically during vSphere upgrades.
D. Perform a scan of new storage devices.
【单选题】
An administrator wants to restore the vCenter Server Appliance 6.5 from backup. Where can this be accomplished?___
A. from the ESXi Host Client
B. from the VMware vSphere Appliance Management Interface
C. from within the VMware vSphere Web Client
D. from the vCenter Server Appliance Installer
【单选题】
The administrator wants to power on VM-K2, which has a 2GHz CPU reservation. VM-M1, VM-M2, and VM-K1 are all powered on. VM-K2 is not powered on. The exhibit shows the parent and child resource reservations. If Resource Pool RP-KID is configured with an expandable reservation, which statement is true?___
A. VM-K2 will be unable to power on because there are insufficient resources.
B. VM-K2 will be able to power on since resource pool RP-KID has 2GHz available.
C. VM-K2 will be unable to power on because only 2GHz are reserved for RP-KID.
D. VM-K2 will receive resource priority and will be able to power on this scenario.
【单选题】
Which is the block size on the VMFS6 datastore?___
A. All small and large file blocks are 8MB.
B. All small and large file blocks are 1MB.
C. Small file blocks are 512KB. large file blocks are 64MB.
D. Small file blocks are 1MB, large file blocks are 512MB.
【单选题】
When installing vCenter Converter Standalone, why must an administrator perform a client-server installation instead of a local installation?___
A. to manage conversion tasks remotely
B. to convert virtual machines as well as physical machines
C. to allow installation of the Converter agent on remote source machines
D. to hot clone physical or virtual machines
【单选题】
Which is required by vCenter Converter Standalone to convert a physical Red Hat Enterprise Linux 7 machine to a virtual machine?___
A. The Linux machine must be powered off.
B. The Linux machine must have the SSH daemon started.
C. The Linux machine must use a static IP address.
D. The Linux machine must have a fully-qualified domain name.
【单选题】
An administrator is troubleshooting network communications between a vCenter Server and an ESXi 6.5 host. Which log shows the related events between these components?___
A. /var/log/fdm.log
B. /var/log/vpxa.log
C. /var/log/hostd.log
D. /var/log/auth.log
【单选题】
An administrator has recently upgraded from vSphere 6.0 to 6.5, and can no longer see the software iSCSI named vmhba33. Which could be the reason for this?___
A. The upgrade has changed the vmhba name.
B. vSphere 6.5 automates iSCSI configurations.
C. vSphere 6.5 no longer supports software iSCSI.
D. The upgrade has deleted the vmhba.
【单选题】
An administrator is trying to vMotion a VM from his datacenter to a recovery site. Which is the maximum allowed RTT (Round-Trip Time) latency between source and destination host?___
A. 100 milliseconds
B. 150 milliseconds
C. 15 milliseconds
D. 10 milliseconds
【单选题】
Which is required for configuring iSCSI Software Adapter network port binding?___
A. VMkernel of the iSCSI traffic must be load balanced using Route based on IP Hash algorithm.
B. VMkernel of the iSCSI traffic must be load balanced using Route based on Source Virtual Port ID algorithm.
C. VMkernel of the iSCSI traffic must be load balanced using Route based on Source MAC Hash algorithm.
D. VMkernel of the iSCSI traffic must be bound to only one active network adapter.
【单选题】
In vSphere Data Protection 6.1, which is the function of a Backup Verification job?___
A. None. Backup Verification job is not a feature of vSphere Data Protection
B. It is a manual task -Power it on -Verify the guest OS -Check started applications
C. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OS is booted by communicating with the Backup Verification agent
D. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OC is booted by detecting the VMware ToolsTM "heartbeats"
【单选题】
An administrator has enabled vSphere Distributed Switch Health Check. The hosts connected to that Distributed Switch all display an alert:< vSphere Distributed Switch MTU supported status > .The administrator has all of the VMkernel ports MTU sizes set to 1600. Which action will remedy this problem?___
A. Configure the Distributed Switch to MTU 9100.
B. Disconnect and reconnect the physical network cable.
C. Configure the physical switch to MTU 1600.
D. Disable the Distributed Switch MTU.
【单选题】
Which Host Profile Subprofile configuration is used to configure firewall settings for ESXi hosts?___
A. Advanced Configuration Settings
B. General System Settings
C. Security
D. Networking
【单选题】
Where would a vSphere administrator find general vCenter Server logs on a vCenter Server Appliance?___
A. /var/log/vmware/vpxd/
B. /var/log/messages
C. /etc/vmware-vpx/
D. /var/log/vmware/vsan-health/
【单选题】
An administrator wishes to enable network port mirroring based on source port. Which feature should be enabled?___
A. vSphere standard switch port
B. ERSPAN
C. NSX Virtual Wire
D. VLAN
【单选题】
Which CLI command shows the physical uplink status for a vmnic?___
A. esxcli network ip connection list
B. esxcli network ip neighbor list
C. esxcli network nic get
D. esxcli network nic list
【单选题】
Which is the maximum number of block devices (LUNs) that are supported by ESXi hosts that are running version 6.5?___
A. 1024
B. 512
C. 2048
D. 256
【单选题】
When performing a vCenter Server 5.5 for Windows with Microsoft SQL Server Express database migration to vCenter Server Appliance 6.5, which will be the target database?___
A. Microsoft SQL Server Express 2012R2
B. Microsoft SQL Server Standard 2012R2
C. PostgreSQL
D. Oracle DB 11g
【单选题】
An administrator has multiple vCenter Server 6.5 systems but cannot enable Storage I/O Control (SIOC) on a datastore shared by ESXi hosts managed by the vCenter Server systems. Which action should the administrator take to resolve the issue?___
A. Unmount the datastore and then enable SIOC on the vCenter Server system.
B. Configure the datastore to be managed by a single vCenter Server system.
C. Configure Storage DRS and then enable SIOC on the vCenter Server system.
D. Enable Raw Device Mapping (RDM) on the
E. SXi hosts.
【单选题】
“OneAppServer” is a VM template stored in a content library named “LibraryOne”, but the vSphere administrator is not able to use this template for deployment. Why is the administrator unable to deploy OneAppServer?___
A. OneAppServer must be updated before it can be deployed.
B. LibraryOne is a subscribed library and OneAppServer is not downloaded yet.
C. LibraryOne is published and optimized for syncing over HTTP.
D. OneAppServer was imported from a local file on the system.
【单选题】
An administrator sets the Failover Capacity for both CPU and Memory at 25%. Based on the Exhibit below, how much of the cluster’s total CPU resources are still available to power on additional virtual machines?___
A. 45%
B. 25%
C. 70%
D. 60%
【单选题】
Which statement applies to the vSphere Replication appliance?___
A. Only one vSphere Replication appliance can be deployed per vCenter Server instance.
B. VMware Tools in the vSphere Replication appliance can be upgraded.
C. A single vSphere Replication appliance can manage a maximum of 4000 replications.
D. vSphere Replication is available only with the vSphere
E. ssentials Plus license.
【单选题】
Which esxcli namespace can a vSphere Administrator use to adjust the queue depth?___
A. esxcli system module parameters
B. esxcli storage core device
C. esxcli system module set
D. esxcli storage core adapter
【单选题】
Which statement regarding datastore clusters meets VMware’s recommended best practices?___
A. Clusters should contain only datastores presented from the same storage array.
B. Clusters should contain only datastores with equal hardware acceleration capability.
C. Clusters should contain only datastores with the same capacity.
D. Clusters should contain only datastores using the same connection method (iSCSI, FC, etc.).
【单选题】
What VM Monitoring setting would ensure that the maximum reset window for a virtual machine is 24 hours?___
A. Medium
B. Low
C. High
D. Normal
【单选题】
What is the default space threshold for vSphere Storage DRS?___
A. 80%
B. 70%
C. 90%
D. 95%
【单选题】
Which is the correct sequence to upgrade a vSphere infrastructure?___
A. vCenter Server>ESXi host> VMware Tools>VM compatibility
B. ESXi host>vCenter Server> VMware Tools>VM compatibility
C. vCenter host> ESXi host> VM compatibility> VMware Tools
D. ESXi host>vCenter Server> VM compatibility>VMware Tools
【单选题】
An administrator has a large boot from SAN cluster and wants to ensure consistent configuration by using host profiles. What special considerations are required for boot from SAN hosts?___
A. Change the “Device is shared clusterwide” setting to “false” in the host profile.
B. Verify that the boot LUN is correctly identified as the boot device in the host profile.
C. The boot from SAN device must report as a local device.
D. Host profiles are incompatible with boot from SAN hosts.
【单选题】
When using VMware Converter to import a Windows server and improve the consistency of the destination virtual machine, which optional step can be performed immediately prior to powering down the source server?___
A. Perform a final synchronization task.
B. Remove the server from the network.
C. Uninstall production applications.
D. Remove the server from the Active Directory domain.
【单选题】
Restoration of the vCenter Server Appliance is accomplished using which interface?___
A. vSphere Web Client
B. vSphere Client
C. vCenter Server Appliance Management Interface
D. vCenter Server Appliance GUI Installer
【单选题】
When attempting to migrate a virtual machine to another host in the same cluster, the error message, “Select a valid compute resource” returns. What could cause this error?___
A. Both hosts run different versions of ESXi.
B. Both hosts are not sharing the same datastore.
C. VMware Tools is not installed.
D. Virtual machine has an ISO attached.
【单选题】
When will vSphere Data Protection delete the expired backup image of a Platform Service Controller?___
A. Immediately after the retention period has expired.
B. After the expired backup image is restored.
C. During the next backup window following expiry.
D. During the next maintenance window following expiry.
【单选题】
Group A has permission to download files in Content Library. Group B does not have permission to download files in Content Library. If a user is a member of both groups, what will be the result?___
A. The user cannot download file from Content Library.
B. The user can download file from Content Library.
C. The user cannot access Content Library.
D. The user can access Content Library.
【单选题】
An administrator is trying to set up Host Partial Failure Response, but the Automated option is grayed out. What can the administrator change to enable the Automated option?___
A. Change the vSphere DRS Automation level to Partially Automated.
B. Change the vSphere DRS Automation level to Fully Automated.
C. Enable vSphere HA Host Monitoring.
D. Change the vSphere DPM Automation level to Automatic.
【单选题】
When you attempt to open a virtual machine console from the vSphere Web Client, the console does not connect. The following error message appears:<HTTP ERROR 404> <Problem accessin/.Reason: Not Found>. Why did not connect?___
A. Port 443 is in use.
B. Port 9443 is in use.
C. Port 8443 is in use.
D. Port 22443 is in use.
【单选题】
What new feature was introduced to the Content Library in vSphere 6.5?___
A. Mount an ISO directly from the Content Library.
B. Deploy a virtual machine from an OVF Package in a Content Library.
C. Upload a File from a URL to a Library Item.
D. Upload a File from a Local System to a Library Item.
