【单选题】
利用熔体熔化作用而切断电路的保护电器叫___。___
A. 自动开关
B. 组合开关
C. 闸刀开关
D. 熔断器
查看试卷,进入试卷练习
微信扫一扫,开始刷题
相关试题
【单选题】
标记速度为160km/h的客车运行___[或距上次各级修程不超过1年]实施A1级检修。___
A. 10万km±2万km
B. 20万km±2万km
C. 30万km±2万km
D. 40万km±2万km
【单选题】
运用客车每年应进行___集中整修。___
【单选题】
段修后,蓄电池容量应为额定容量的___以上。___
A. 60%
B. 70%
C. 80%
D. 90%
【单选题】
车辆段___应安排一次辅修或A1级检修的质量对规。___
【单选题】
铁路局___应安排一次辅修或A1级检修的质量对规。___
【单选题】
容量在___W以上的交流电动机一般采用降压启动。___
A. 4000
B. 5000
C. 6000
D. 7000
【单选题】
运用列车质量鉴定评分标准分为A,B,C,D四类,发现B类故障[问题],每处每件扣___。___
A. 5分
B. 10分
C. 20分
D. 50分
【单选题】
安装电子防滑器的速度传感器时,其软管部分的最大弯曲半径为___MM。___
A. 50
B. 80
C. 110
D. 140
【单选题】
运用列车质量鉴定评分标准分为A,B,C,D四类,管理部分发现D类问题,此项得___。___
A. 0分
B. 10分
C. 20分
D. 50分
【单选题】
客车轴温达到90℃或超过外温加___时摘车处理。___
A. 40℃
B. 50℃
C. 60℃
D. 70℃
【单选题】
空调列车电力连接线的长度一般为___MM。___
A. 1400-1500
B. 1500-1600
C. 1600-1700
D. 1700-1800
【单选题】
临时换挂、加挂客车,铁路局客运调度员应于列车出发前___通知车辆调度员,由库列检、客列检按规定检修车辆。___
【单选题】
客车燃煤取暖锅炉,在点火运用时锅炉内的水温不得超过___℃。___
【单选题】
采用中间体过渡车钩调车时,一次连挂不得超过4辆,运行速度不得超过___。___
A. 40km/h
B. 50km/h
C. 60km/h
D. 80km/h
【单选题】
机车供电的空调客车,在列车始发前___连挂机车后须立即开启空调对车厢进行预冷、预热。___
A. 20min
B. 30min
C. 40min
D. 50min
【单选题】
KP-2A型控制箱中的D7断路时___。___
A. 发电机不发电
B. 电压失控
C. 误动作
D. 正常
【单选题】
空调客车的空调温控器冬季应设定为___。___
A. 14~16℃
B. 16~18℃
C. 18~20℃
D. 20~22℃
【单选题】
空调装置电气部件与壳的绝缘电阻应大于___兆欧。___
【单选题】
空调客车的空调温控器夏季应设定为___。___
A. 18~22℃
B. 22~26℃
C. 24~28℃
D. 26~30℃
【单选题】
当空调客车的环境温度低于___时,严禁开启空调设备制冷。___
A. 15℃
B. 16℃
C. 17℃
D. 18℃
【单选题】
稳压接到电源上,必须串联一个___。___
A. 二极管
B. 三极管
C. 电容器
D. 电阻
【单选题】
当空调客车的环境温度低于___时,严禁开启电伴热装置。___
【单选题】
只要控制基极___,即可使三极管处于截止状态。___
【单选题】
装有空气弹簧的客车,运行途中发生空气弹簧故障时应限速运行,运行速度不得超过___。___
A. 60km/h
B. 80km/h
C. 120km/h
D. 160km/h
【单选题】
下列属于有机绝缘材料的是___。___
【单选题】
列车整备原则上应使用外接电源供电,用电时间一般不超过___。___
【单选题】
KP-2A控制过压保护回路发生故障时可能会发生___。___
A. 失控
B. 不发电
C. 误动作
D. 正常
【单选题】
新造25T型客车上线运行前,须进行通电、带载试运行,试运行距离原则上不得少于___。___
A. 500km
B. 1000km
C. 1500km
D. 2000km
【单选题】
新造蓄电池在工厂内进行的一种充电叫___。___
A. 初充电
B. 补充电
C. 普通充电
D. 化成充电
【单选题】
登高作业使用梯子,梯子与地面的倾斜角为___左右,并要有防滑装置。___
A. 30°
B. 45°
C. 60°
D. 80°
【单选题】
露天工作场所遇有___以上大风时禁止高空作业。___
【单选题】
使用手提式风钻、电钻,操作时站立位置要适当,钻孔高度不得超过工作者___,不得用力过猛。___
【单选题】
氧气瓶与乙炔发生器的距离应在___以上。___
【单选题】
氧气瓶及乙炔发生器的距离明火应在___以上。___
A. 5m
B. 10m
C. 15m
D. 20m
【单选题】
《铁路技术管理规程》是根据___与《铁路运输安全保护条例》制定的。___
A. 《铁路法》
B. 《劳动法》
C. 《宪法》
D. 《刑法》
【单选题】
铁路基本建设项目中的环境保护、水土保持、劳动安全、劳动卫生及消防等设施,必须和主体工程___。___
A. 同时设计、同时施工、同时投产
B. 同时设计、同时施工、同时报废
C. 同时设计、同时投产、同时报废
D. 同时施工、同时投产、同时报废
【单选题】
车辆修程,客车和特种用途车按走行公里进行检修,最高运行速度不超过120km/h的客车分为___。___
A. 厂修、辅修、临修
B. 厂修、段修、辅修
C. 段修、辅修、临修
D. 厂修、段修、临修
【单选题】
车辆须装有自动制动机和人力制动机,车辆的下拉杆、交叉杆、抗侧滚扭杆和___必须有保安装置。___
A. 制动梁、上拉杆
B. 制动梁、横向控制杆
C. 上拉杆、横向油压减振器
D. 制动梁、横向油压减振器
【单选题】
最高运行速度160km/h及以上的客车应采用___,安装客车行车安全监测系统。___
A. 密接式车钩
B. 15号车钩
C. 中间体过渡车钩
D. 15号过渡车钩
【单选题】
列车按运输性质分为旅客列车、路用列车和___。___
A. 行邮行包列车、混合列车、货物列车
B. 行邮行包列车、混合列车、军用列车
C. 行邮行包列车、军用列车、货物列车
D. 货物列车、混合列车、军用列车
推荐试题
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
【单选题】
An administrator is installing Windows into a virtual machine. The DVD has been mounted on the Host and configured for the virtual machine as shown in the Exhibit. Based on the exhibit, when the virtual machine is booted, why would it attempt to search for a PXE server? ___
A. The CD/DVD device is not connected.
B. The ISO is in the incorrect storage location.
C. The OS minimum requirements have not been met.
D. The CD/DVD device is not set to Client Device.
【单选题】
What component must be installed prior to deploying a vCenter Server in vSphere 6.x? ___
A. vCenter Identity Services
B. Platform Services Controller
C. vCenter Single Sign-On
D. Client Integration Plug-In
【单选题】
What is a valid plug-in status for a plug-in that has been added to a vSphere client? ___
A. Disabled
B. Unknown
C. Stopped
D. Installed
【单选题】
Users of an application are reporting performance issues. The following performance values are observed in the vSphere Web Client: <Host CPU utilization is 90%> <Virtual Machine memory utilization is consistently greater than 90% CPU Ready values are higher than 20%> What could be the cause of the application performance issue? ___
A. The host is lacking the CPU resources required to meet the demand.
B. The host is lacking the memory resources required to meet the demand.
C. The virtual machine is lacking the CPU resources required to meet the demand.
D. The virtual machine is lacking the memory resources required to meet the demand.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is re-provisioning an ESXi host and moving it to another datacenter. Which DCUI option should the administrator use to revert the system configuration to the default settings? ___
A. Reset System Configuration
B. Rebuild Default System Configuration
C. Revert System Configuration
D. Renew Default System Configuration
【单选题】
An administrator has just completed installing an ESXi 6.x host, but doesn't know what address has been configured. Where is the ESXi host IP address configured? ___
A. RVC console
B. Direct Console User Interface
C. vSphere Web Client
D. vSphere Client
【单选题】
When is it possible to place a VMFS5 datastore in maintenance mode? ___
A. When it is a member of a Storage DRS cluster
B. When it is a member of Virtual SAN cluster
C. When it is a member of a multi-extent datastore
D. When it is a member of a Virtual Volume
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Which Single Sign-On deployment mode should an administrator use for two 6.x vCenter Servers configured with linked mode? ___
A. Basic Single Sign-On with vCenter Server Heartbeat
B. Multisite Single Sign-On
C. Basic Single Sign-On
D. Single Sign-On with Linked Mode
【单选题】
What is required when changing a virtual machine name using the vSphere Web Client? ___
A. Verify connectivity to the ESXi host where the virtual machine is running and its inventory list is accessible.
B. Verify in which datastore the virtual machine resides and that you have access and its inventory list is accessible.
C. Verify that virtual machine files are stored in the same datastore and can be accessed in the datastore browser list.
D. Verify the virtual machine is not running in Fault Tolerant mode and that it is not in a Distributed Resource Scheduler cluster.
【单选题】
An administrator deploys vRealize Operations into a vSphere 6.x environment. After the deployment, the administrator notices that badges are not appearing. What is a likely cause of this behavior? ___
A. Badges do not appear until you register vRealize Operations with vCenter Server.
B. Badges do not appear until you register a vCenter Server in vRealize Operations.
C. The vRealize Operations appliance needs to be redeployed.
D. The vCenter Server appliance needs to be redeployed.