刷题
导入试题
【单选题】
户外落地变压器外廓与建筑物外墙距离小于【】m时,应考虑对建筑物的防火要求。___
A. 4
B. 5
C. 1
D. 2
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
B
解析
暂无解析
相关试题
【单选题】
用500V兆欧表测氧化锌0.22kV避雷器的绝缘电阻应不低于【】。___
A. 2MΩ
B. 10MΩ
C. 0.5MΩ
D. 5MΩ
【单选题】
高低压塑料绝缘电力电缆最低允许敷设温度为【】℃。___
A. 15
B. 10
C. KONG
D. 0
【单选题】
对于【】负荷,应由两个或多个电源供电。___
A. 1级
B. 2级
C. 3级
D. 特殊
【单选题】
电动机长时间过负载运行,【】大大超过额定电流,电动机过热。___
A. 转子电流
B. 绕组电流
C. 定子电流
D. 最小电流
【单选题】
成套开关柜、配电盘等漏电保护装置的动作电流数值选择为【】mA以上。___
A. 10
B. 100
C. 15
D. 50
【单选题】
某10kV高供高计用户接50/5电流互感器,若电能表读数为20kWh,则用户实际用电量为【】。___
A. 200kWh
B. 20000kWh
C. 2000kWh
D. 100000kWh
【单选题】
某村低压线路烧毁,需要检修处理,于是工作负责人就【】登杆检修。___
A. 立即派人
B. 经验明确无电压后
C. 经验明确无电压后,挂好接地线派人
D. 填写第二种工作票后立即派人
【单选题】
容量在【】kVA及以上的配电变压器,应装设空气过滤器。___
A. 60
B. 80
C. 100
D. 120
【单选题】
起重搬运工作,当设备需从低处运至高处时,可搭设斜坡下走道,但坡度应小于【】。___
A. 30
B. 25
C. 20
D. 15
【单选题】
使用电容器时有两项主要参数,即耐压值和电容量,而电容器耐压值是指加在其上电压的【】。___
A. 最大值
B. 瞬时值
C. 有效值
D. 平均值
【单选题】
一电感线圈接到f=50Hz的交流电路中,感抗XL=50Ω,若改接到f=150Hz的电源时,则感抗XL为【】Ω。___
A. 150
B. 250
C. 10
D. 60
【单选题】
断路器的额定电压应【】系统最高电压。___
A. 等于
B. 大于
C. 小于
D. 等于或大于
【单选题】
SL-2A型设备线夹适用的导线截面【】mm2。___
A. 35~50
B. 70~95
C. 120~150
D. 70~120
【单选题】
用于接通和断开电容器组的断路器其额定电流不应低于【】倍电容器组的额定电流。___
A. 1.1
B. 1.2
C. 1.3
D. 1.5
【单选题】
某工业用户一级重要电力客户,根据《国家电网公司业扩供电方案编制导则》规定,其供电电源【】采用双电源供电,并配置自备应急电源。___
A. 宜
B. 可
C. 应
D. 不应
【单选题】
集中器、采集终端等装置安装高度应适当,在电表房或电缆竖井内,如受位置局限,可适当降低安装高度,但底部离地面不得小于【】米。___
A. 0.5
B. 0.6
C. 0.7
D. 0.8
【单选题】
经电流互感器接入的低压三相四线电能表,其电压引入线应【】。___
A. 单独接入
B. 与电流线共用
C. 接在电流互感器二次测
D. 在电源侧母线螺丝出引出
【单选题】
《国网业扩供电方案编制导则》规定:【】在电网高峰负荷时功率因数不宜低于0.85。___
A. 100kVA及以上高压供电的电力客户
B. 其他电力客户和大中型电力排灌站
C. 农业用电客户
D. 趸购转售电企业
【单选题】
居民使用的单相电能表的工作电压是【】。___
A. 220V
B. 380V
C. 100V
D. KONG
【单选题】
地锚的抗拔力是指地锚受外力垂直向上的分力作用时,抵抗【】滑动的能力。___
A. 向左
B. 向右
C. 向上
D. 向下
【单选题】
楔形线夹属于【】金具。___
A. 接续
B. 联接
C. 拉线
D. 保护
【单选题】
10kV及以下电力接户线固定端当采用绑扎固定时,其绑扎长度应满足:当导线为25~50mm2时,应绑扎长度【】。___
A. ≥50mm
B. ≥80mm
C. ≥120mm
D. ≥200mm
【单选题】
剩余电流动作保护器安装时应避开邻近的导线和电气设备的【】干扰。___
A. 磁场
B. 电场
C. 电磁场
D. 电磁波
【单选题】
对已运行的电缆中间接头电阻与同长度同截面导线的电阻相比,其比值不应大于【】。___
A. 1
B. 1.2
C. 1.4
D. 1.5
【单选题】
按故障部位划分,电缆线路故障可分为【】。___
A. 接头故障和终端故障
B. 接地故障和断线故障
C. 本体故障和附件故障
D. 闪络故障和绝缘故障
【单选题】
两台单相电压互感器按V/V形连接,二次侧v相接地。若电压互感器额定变比为10000V/100V,一次侧接入线电压为10000V的三相对称电压。带电检查二次回路电压时,电压表一端接地,另一端接U相,此时电压表的指示值为【】V左右。___
A. 58
B. 100
C. 173
D. 0
【单选题】
《国家电网公司电费抄核收管理规则》规定,远程自动抄表正常运行后,对连续三个抄表周期出现抄表数据为零度的客户,0.4千伏非居民客户应抽取不少于的【】客户进行现场核实。___
A. 全部
B. 20%
C. 70%
D. 80%
【单选题】
三相电力变压器组别标号为D,yn2,所表示的是【】。___
A. 一次与二次线电压的相量差
B. 一、二次电流相量差
C. 铁芯与绕组的角度差
D. 电压电流相量差
【单选题】
剩余电流动作保护器对【】之间的漏电引起的危险能起保护作用。___
A. 相与相
B. 相与零
C. 相与地
D. 零与零
【单选题】
摇测电容器、电力电缆、大容量变压器、电机等设备时,绝缘电阻表必须在【】下,方可将测量笔接触或离开被测设备。___
A. 停转状态
B. 额定转速状态
C. 高速转动状态
D. 逐渐降速状态
【单选题】
绝缘套管表面的空气发生放电,叫【】。___
A. 气体放电
B. 气体击穿
C. 瓷质击穿
D. 沿面放电
【单选题】
对变压器绝缘影响最大的是【】。___
A. 温度
B. 水分
C. 杂质
D. 纯度
【单选题】
真空断路器的关键部件是【】。___
A. 真空灭弧室
B. 屏蔽罩
C. 波纹管
D. 动静触头
【单选题】
搭设跨越公路的跨越架,距路面的高度为【】。___
A. 4.5m
B. 5.5m
C. 6.5m
D. 7.5m
【单选题】
国家电网公司提出的“三集五大”中的‘三集“是指:【】___
A. 集团化、集约化、集中化
B. 人力资源、财务和物资集约化
C. 人力资源、财务和信息集约化
D. 财务、信息和物资集约化
【单选题】
在电价低的供电线路上,擅自接用电价高的用电设备或私自改变用电类别的,应按实际使用日期补交其差额电费,并承担【】倍差额电费的违约使用电费。___
A. 2
B. 3
C. 4
D. 5
【单选题】
纯电容电路的电压与电流频率相同,电流的相位超前于外加电压u为【】度。___
A. 60
B. 30
C. 90
D. 180
【单选题】
某低压配电室电源进线断路器两侧都装有隔离开关,在送电操作时,首先应合上【】。___
A. 电源进线断路器
B. 电源侧隔离开关
C. 负荷侧隔离开关
D. 无顺序要求
【单选题】
斜削法需先用电工刀以【】度角倾斜切入绝缘层,当切近芯线时,即停止用力。___
A. 45
B. 35
C. 25
D. 15
【单选题】
高压验电器绝缘部分长度,对10kV及以下不小于【】m。___
A. 0.8
B. 0.4
C. 1
D. 0.9
推荐试题
【判断题】
两孔轴线相交成 90°角,一个孔直径为φ20mm,另一个孔直径是φ30mm,应该先钻穿直径大的孔
A. 对
B. 错
【判断题】
碳素工具钢和合金工具钢用于制造中、低速成型刀具
A. 对
B. 错
【判断题】
经纬仪整平时,经反复调整,直到仪器转到任意位置时,水准气泡最大偏离值小于二分之一格为止
A. 对
B. 错
【判断题】
刮削大型机床导轨面时,应在将导轨面上的零件全部拆除后进行,以保证刮削质量
A. 对
B. 错
【判断题】
要安排好培训计划,做好上课的准备工作,做到有组织,有计划地进行培训,做到定时间,定地点,定内容,定进度,定要求,有练习,有考核
A. 对
B. 错
【判断题】
轨道制作主要是轨道调直和接头,调直后对轨道进行编号,两条轨道上从端部或伸缩缝处算起,轨道接头至少要对齐,以使运转平稳
A. 对
B. 错
【判断题】
为实现电动机连续正转运行需采用具有接触器自锁的控制线路和手动正转控制回路
A. 对
B. 错
【判断题】
在修理带传动机构时,发现带轮孔超差额0.08mm,造成配合过松,一般可用镀铬法来加大轴颈尺寸
A. 对
B. 错
【判断题】
用经纬仪和平行光管测量机床转台分度误差时,应用专用心轴配装在转台中心孔中将经纬仪和心轴紧固联接在一起
A. 对
B. 错
【判断题】
采用双螺母螺纹式调整滚珠丝杠轴向间隙的方法结构紧凑,调整方便,应用广泛
A. 对
B. 错
【判断题】
若自准直仪上读数鼓轮每格角值分度值为1",则其线值分度值可用0.05mm/m表示
A. 对
B. 错
【判断题】
所有的紫色酒精,在 1 米内不准点有明火,不准放在暖气片上
A. 对
B. 错
【判断题】
固定式装配适用于单件和小批量模具的装配,以及装配精度要求较高,需要调整的部位较多的装配
A. 对
B. 错
【判断题】
我国对企业发生的事故,坚持“四不放过”原则进行处理
A. 对
B. 错
【判断题】
齿轮的齿侧间隙分为12 个等级
A. 对
B. 错
【判断题】
在机械设备中,凸轮表面误差将会引起扭转振动
A. 对
B. 错
【单选题】
What happens to the status of users already logged into ESXi Shell when a vSphere administrator enables lockdown mode?___
A. Users remain logged in and can run commands, except to disable lockdown mode.
B. Users remain logged in and can run commands, including disabling lockdown mode.
C. Users are immediately logged out of ESXi Shell.
D. Users are logged out after a timeout specified by the vSphere administrator.
【单选题】
What is the effective vSphere licensing level during the 60 day evaluation period?___
A. vSphere Foundation Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
【单选题】
To comply with security requirements, an administrator with a vCenter Server Appliance needs to force logoff of the vSphere web client after 10 minutes of inactivity.What should the administrator do to meet the requirement?___
A. Edit: /var/lib/vmware/vsphere-client/webclient.properties, modify session.timeout=10
B. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=600
C. Edit: /var/lib/vmware/vsphere-client/webclient.properties modify session.timeout=600
D. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=10
【单选题】
An administrator enables High Availability (HA) on a Virtual SAN cluster.Which network is used for HA Network Heatbeat configuration?___
A. The Management network.
B. The vMotion network.
C. The Virtual SAN network.
D. The Provisioning Traffic network.
【单选题】
A user wants to monitor a business-critical virtual machine to ensure that it doesn't run out of resources. What metric could be monitored in vRealize Operations to address this concern?___
A. Time Remaining badge
B. Compliance badge
C. Reclaimable Waste badge
D. Density badge
【单选题】
An administrator has recently installed a new ESXi 6.x Host, and during the configuration notices sporadic network problems. To check whether the issue occurred sometime during the configuration, the administrator would like to reset the system.How can this be accomplished in the shortest amount of time?___
A. Run the ESXi installer again and reinstall the host.
B. Select the Reset System Configuration option from the vSphere Client when connected directly to the host.
C. From the
D. irect Console User Interface, select Reset System Configuration.
【单选题】
A vApp is running out of compute resources when overall activity is high within the resource pool. At other times, everything is fine.What should be done to resolve this issue?___
A. Increase the size of the resource pool Shares.
B. Set the vApp's CPU and Memory Reservation Type to Expandable.
C. Set the vApp's CPU and Memory Limit to Unlimited.
D. Create a new resource pool with the existing hardware configuration.
【单选题】
A virtual machine has been renamed and an administrator is unable to find files with the new virtual machine name in the datastore.What is the reason for this?___
A. The names of the files on the datastore do not change.
B. The names of the files on the datastore have been corrupted.
C. The virtual machine needs to be re-added to the inventory.
D. The Distributed Resource Scheduler moved the virtual machine to another host.
【单选题】
An administrator has configured network connectivity for a new virtual machine, as shown in the Exhibit.What will occur with the network traffic of this virtual machine when communicating externally from vSwitch1?___
A. The virtual machine will communicate on both uplinks
B. The virtual machine will only communicate on vmnic1
C. The virtual machine will only communicate on vmnic2
D. The virtual machine will fail to communicate externally
【单选题】
An administrator is unable to create the first group in a new vRealize Operations environment. What is the likely cause of the problem?___
A. There are no group types defined.
B. The group is not defined in SSO.
C. There are more than 32 group types defined.
D. The description for the group is not provided.
【单选题】
A new vApp was built and tested in the corporate headquarters datacenter running vSphere 6.x. What condition would explain why the virtual machine is failing to boot in an offsite datacenter running on vSphere 5.5?___
A. The virtual machine was built with the default hardware version.
B. The VMFS 5 datastore is not compatible with virtual machines configured with vSphere 6.x.
C. a
D. RS 5.5 cluster cannot run virtual machines configured with vSphere 6.x.
【单选题】
An administrator is evaluating whether to deploy vCenter Server on a Windows server or on a vCenter Server appliance. The administrator has the following requirements: <A web browser will be utilized to manage the vSphere environment.> <16 ESXi hosts will be deployed.> <Licenses must be shared with a vCenter Server at another site.> <An external Oracle 10g database server will be used to host the vCenter Server database.> Why will the administrator need to deploy vCenter Server on a Windows server?___
A. Linked Mode is a requirement for the solution.
B. Oracle 10g is a requirement for the solution.
C. The vSphere web client is a requirement for the solution.
D. Management of more than 5 hosts is a requirement for the solution.
【单选题】
What is a benefit of using VMware Data Protection ?___
A. Provides support for guest-level backups and restores of Microsoft SQL Servers, Exchange Servers, and Share Point Servers.
B. Provides support for advanced storage services including replication, encryption, deduplication, and compression.
C. Provides direct access to VDP configuration integrated into the vSphere Client.
D. Reduces disk space consumed by virtual machine data using deduplication.
【单选题】
An administrator enables vSphere High Availability (HA) on an existing cluster with a large number of hosts and virtual machines. The administrator notices that the setup of vSphere HA on some of the hosts is failing. What step, if taken, might resolve this issue?___
A. Increase the value of the config.vpxd.das.electionWaitTimeSec setting.
B. Set the value of vpxd.das.aamMemoryLimit to 256.
C. Set the value of the das.useDefaultIsolationAddress setting to False.
D. Increase the value of the das.iostatsinterval setting.
【单选题】
An ESXi 6.x host consists of 24 logical cores. Hyperthreading is enabled on the host. What is the maximum number of vCPUs that can be assigned to a virtual machine on this host?___
A. 24
B. 48
C. 64
D. 128
【单选题】
By default, each ESXi 6.x host is provisioned with a certificate from which root certificate authority?___
A. RedHat Certificate Authority
B. VMware Certificate Authority
C. DigiCert Certificate Authority
D. Verisign Certificate Authority
【单选题】
An administrator is adding an NFS datastore as shown in the Exhibit. What is the purpose of the Servers to be added list?___
A. It contains the IP addresses of the NFS Storage Server to provide multipathing capability.
B. It contains the IP addresses of the ESXi hosts that mount the datastore.
C. It contains the IP addresses used for
D. ynamic Discovery of targets.
【单选题】
An administrator reports that the System Event log data is only available for 24 hours when reviewing the Hardware Status tab. Which condition could be responsible for the loss of data?___
A. A Reset event log was executed.
B. The statistical collection level was set to a value of 1.
C. The boot disk of the host is corrupt.
D. Syslog has been configured at the vCenter Server level.
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
欢迎使用我爱刷题
×
微信搜索我爱刷题小程序
温馨提示
×
请在电脑上登陆“www.woaishuati.com”使用