【填空题】
11.当断缝小于50mm时，应立即进行紧急处理。在断缝处上好夹板或臌包夹板，用急救器固定，在断缝前后各50m拧紧扣件，并派人看守，限速放行列车速度为___。
查看试卷，进入试卷练习
微信扫一扫，开始刷题
相关试题
【填空题】
12.钢轨铝热焊焊缝接头应平整圆顺，用1m直尺测量，顶面、侧面不平度应在___以内，顶面不得有负值。
【填空题】
13.氧气瓶、丙烷瓶在焊接和切割火焰的上风方向和侧风方向，禁止布置在火焰的___方向的。
【填空题】
14.丙烷瓶与明火的距离不得小于___。
【填空题】
15.丙烷瓶与氧气瓶的距离不得小于___。
【填空题】
16.在钢轨焊接中，含碳量高的钢轨比含碳量低的可焊性___。
【填空题】
17.37°探头探测钢轨使用的是___。
【填空题】
18.70°探头探测轨头时只有二次波显示位移量较大应___。
【填空题】
20.超声波到达两个不同材料的界面上，可能发生___。
【填空题】
21.被放大的信号幅度与缺陷的反射面积成正比地增大，放大器这一非饱和的放大区域称为___。
【填空题】
22.超声波探伤仪中，产生时间基线的部分叫做___。
【填空题】
23.探测厚焊缝中垂直于表面的缺陷最适用的方法是___。
【填空题】
24.钢轨焊缝中的各种缺陷最不容易检测的缺陷有___。
【填空题】
25.探头发射脉冲声波的___是表示探头频率特性的最合理的数据。
【填空题】
26.钢轨核伤的是由哪种原因发展形成的___。
【填空题】
27.同种材料中，在给定频率下产生波长短的波动形式是___。
【填空题】
28.因表面粗糙使超声波束产生的漫射叫做___。
【填空题】
29.材料的声速与密度的乘积，可决定超声波在界面上的声能反射率与透过率，这一乘积称为___。
【填空题】
30.一定频率的超声波通过声速低的材料时，其波长将比通过声速高的材料时___。
【填空题】
32.缺陷的当量尺寸总是___缺陷的实际尺寸。
【单选题】
我国城市轨道交通采用___为标准轨距。
A. 1425mm
B. 1430mm
C. 1435mm
D. 1440mm
【单选题】
作业验收时，轨距误差：规定宽不得超过___。
A. 4mm
B. 5mm
C. 6mm
D. 7mm
【单选题】
作业验收时，轨距误差：规定窄不得超过___。
A. 5mm
B. 4mm
C. 3mm
D. 2mm
【单选题】
在线路直线部分，轨距不应大于___。
A. 1438mm
B. 1439mm
C. 1440mm
D. 1441mm
【单选题】
在线路直线部分，轨距不应小于___。
A. 1431mm
B. 1432mm
C. 1433mm
D. 1434mm
【单选题】
轨距测量在日常检查中，通常每___检查一处。
A. 6.20m
B. 6.25m
C. 6.30m
D. 6.35m
【单选题】
轨距的大小是由机车车辆的轮对___确定的。
【单选题】
我国国家标准规定正直线轨距误差的允许范围为在___。
A. +6mm~-2mm
B. +8mm~-4mm
C. +10mm~-6mm
D. +12mm~-8mm
【单选题】
我国国家标准规定正直线轨距误差的允许范围保养标准为___。
A. +6mm~-2mm
B. +8mm~-4mm
C. +10mm~-6mm
D. +12mm~-8mm
【单选题】
我国国家标准规定正直线1m范围内轨距不得有___以上的误差。
A. 4mm
B. 3mm
C. 2mm
D. 1mm
【单选题】
在日常检查时，水平也用道尺进行检查，通常每___检查一处。
A. 6.25m
B. 6.30m
C. 6.35m
D. 6.40m
【单选题】
《铁路技术管理规程》中规定：水平的允许误差，在维修线路的正线，到发线上，不得大于___。
A. 3mm
B. 4mm
C. 5mm
D. 6mm
【单选题】
铁路技术管理规程》中规定：水平的允许误差，在维修线路的正线，到发线上，不得大于4mm，其他线不得大于___为基准。
A. 6mm
B. 5mm
C. 4mm
D. 3mm
【单选题】
水平的变化率1m距离内，变化不得超过___。
A. 2mm
B. 1mm
C. 10mm
D. 20mm
【单选题】
线路上先是左股钢轨高，后是右股钢轨高，当前后两点的水平正负误差的代数差超过___时为三角坑。
A. 2mm
B. 3mm
C. 4mm
D. 5mm
【单选题】
在检查三角坑时，基长为6.25m，但在延长___的距离内应不允许出现三角坑。
A. 15m
B. 16m
C. 17m
D. 18m
推荐试题
【单选题】
which technology cloud be used on top of an MPLS VPN to add confidentiality ？___
A. IPsec
B. 3DES
C. AES
D. SSL
【单选题】
Which term is most closely aligned with the basic purpose of a SIEM solution? ___
A. Non-Repudiation
B. Accountability
C. Causality
D. Repudiation
【单选题】
You have just deployed SNMPv3 in your environment， Your manager asks you to make sure that our SNMP agents can only talk to the SNMP Manager. What would you configure on your SNMI agents to satisfy this request？___
A. A SNMP View containing the SNMP managers
B. Routing Filter with the SNMP managers in it applied outbound
C. A standard ACL containing the SNMP managers applied to the SNMP configuration
D. A SNMP Group containing the SNMP managers
【单选题】
Which feature prevents loops by moving a nontrunking port into an errdisable state when a BPDU is received on that port？___
A. BPDU filte
B. DHCP snooping
C. BPDU guard
D. Port Fast
【单选题】
Which command enables port security to use sticky MAC addresses on a switch？___
A. switchport port-security violation restrict
B. switchport port-security mac-address sticky
C. switchport port-security violation protect
D. switchport port-security
【单选题】
When you edit an IPS subsignature， what is the effect on the parent signature and the family of subsignatures？___
A. The change applies to the parent signature and the entire family of subsignatures
B. The change applies to the parent signature and the subsignature that you edit
C. The change applies only to subsignatures that are numbered sequentially after the subsignature that you edit
D. Other signatures are unaffected， the change applies only to the subsignature that you dit
【单选题】
Which type of mechanism does Cisco FirePOWER de ploy to protect ag detected moving across other networks？___
A. antivirus scanning
B. policy-based
C. reputation-based
D. signature-based
【单选题】
What action must you take on the ise to blacklist a wired device？___
A. Locate the switch through which the device is connected and push an a cl restricting all access by the device
B. Issue a CoA request for the de vice's mac address to each access switch in the network
C. Revoke the device's certificate so it is unable to authenticate to the network
D. Add the device's MAc address to a list of black listed devices
【单选题】
Which type of firewall can perform deep packet inspection？___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing？___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication？___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning？___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5， but does not use encryption？___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist， using security intelligence to block illicit network activity. However， the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites？___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat（ins，any）dynamic interface】Which ty pe of NaT is configured on a Cisco ASA？___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network？___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration？___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS？___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security？___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true？ ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication，authorization，and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10？___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center？___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true？___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed？___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1．三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
5．熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6．热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7．交流接触器的作用是可以___接通和断开负载。
【单选题】
8．三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9．三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11．熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12．对于电阻性负载，熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13．对于电动机负载，熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3．5
【单选题】
14．使用快速熔断器时，一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
