【单选题】
When Beijing time is 0801,Zulu time should be______.___
A. 2001
B. 1
C. 601
D. 1601
查看试卷,进入试卷练习
微信扫一扫,开始刷题
相关试题
【单选题】
Emergency frequency is______.___
A. 121.5MHZ
B. 120.5MHZ
C. 121MHZ
D. 119.0MHZ
【单选题】
“PAN” is the international RTF______signal___
A. emergency
B. distress
C. urgency
D. dangerous
【单选题】
“MAYDAY” is the international RTF______signal.___
A. emergency
B. distress
C. urgency
D. dangerous
【单选题】
According to ICAO definition, a condition concerning the safety of an aircraft or other vehicle or of some person on board or within sight but which does not require immediate assistance is _______ .___
A. urgency
B. dangerous
C. emergency
D. distress
【单选题】
Which SSR Code is not right?___
A. 7020
B. 8025
C. 6060
D. 4021
【单选题】
______is the accepted standard for worldwide time signal broadcast used for aviation.___
A. GMT
B. LT
C. UTC
D. SST
【单选题】
_____means the level is measured in 1013.2 pha___
A. Level
B. Height
C. Altitude
D. Flight level
【单选题】
An aircraft known or believed to be in a state of emergency should be given______over other aircraft.___
A. way
B. flight plan
C. instruction
D. priority
【单选题】
管制话筒正确使用方法是:___
A. PTT发射键还没有完全按下时就开始发指令
B. 指令还没有结束就松开PTT发射键
C. 按PTT发射键与发话同时进行,松开PTT发射键与发话同时进行
D. 先按下话筒PTT发射键,然后再开始对空发话,发话完毕后再松开话筒PTT发射键
【单选题】
SSR code is a______digital number.___
A. two
B. six
C. one
D. four
【单选题】
Traffic information should include_________
A. direction of aircraft concerned
B. weather
C. speed of aircraft
D. heading of aircraft
【单选题】
根据区管中心业务通告,管制员通知机组转换频率的管制指令应当与其他管制指令( )。___
【单选题】
20NM is equal to.___
A. 40km
B. 38km
C. 37km
D. 41km
【单选题】
The altimeter setting used in en-route flight should be______hpa___
A. 1019
B. 1013
C. 2992
D. 1000
【单选题】
Larger separations than the specified minima should be applied whenever in.___
A. turbulence
B. bad weather
C. a raining day
D. highlevel
【单选题】
_______is air traffic control service for controlled flights in control areas___
A. Route service
B. En-route fly service
C. Area control service
D. Deviation control service
【单选题】
_______ is a service provided to notify appropriate organizations regarding aircraft in need of search and rescue aid, and assist such organizations as required.___
A. alerting service
B. information service
C. rescue service
D. assistance service
【单选题】
Visibility is the ability as determined by atmospheric conditions and expressed in unit______.___
A. meters
B. feet
C. distance
D. odometer
【单选题】
SIGMET is a weather advisory issued concerning weather______to the safety of all aircraft.___
A. significant
B. changeable
C. information
D. condition
【单选题】
Flight level is a______of constant atmospheric pressure which is related to a specific pressure datum 1013.2hpa.___
A. standard
B. surface
C. height
D. number
【单选题】
Air traffic means all aircraft in flight or operating on the______of an aerodrome.___
A. highway
B. hanger
C. maneuvering area
D. terminal
【单选题】
The true airspeed is the airspeed of an aircraft relative to______air.___
A. turbulence
B. smooth
C. undisturbed
D. the
【单选题】
Air speed is the speed of an aircraft relative to its surrounding______.___
A. traffic
B. airmass
C. clouds
D. wind
【单选题】
“Aircraft” means any machine that can derive support in the______from there actions of the air other than there actions of the air against the earth's surface.___
A. atmosphere
B. water
C. sea
D. lake
【单选题】
If the radar receiver detects the retarding time tR=500mS between transmitting pulse and receiving pulse,now the target is______km from the radar station.___
A. 150
B. 120
C. 100
D. 75
【单选题】
“Advise______”means“ Tell me what you plan to do”.___
A. wanting
B. intentions
C. ideas
D. command
【单选题】
The recommendation is advisory in nature.The decision as to whether the flight can be conducted safely rests solely with the______.___
A. controller
B. manager
C. pilot
D. passengers
【单选题】
“There are broken______along the entire route between niner and one one thousand feet at the present time.”___
A. radial
B. clouds
C. weather
D. way
【单选题】
Th evertical speed in dicator measures______of climb or descent.___
A. time
B. point
C. rate
D. distance
【单选题】
A magnetic compass is the______air navigation instrument.___
A. basic
B. advanced
C. computer
D. improved
【单选题】
In the AFTN,the flight plan filing time shall consist of a______data-time group.___
A. four-digit
B. five-digit
C. six-digit
D. eight-digit
【单选题】
“______”is a notice containing information concerning the establishment,condition or change in any aeronautical facility service procedure or hazard,the timely knowledge of which is essential to personnel concerned with flight operations.___
A. AIP
B. SIGMT
C. NOTAM
D. AMP
【单选题】
“______”means visibility,cloud and present weather better than prescribed values or conditions.___
A. Weather clear
B. RVRQK
C. CAVOK
D. VisibilityOK
【单选题】
“______”is the height above the ground or water of the base of the lowest layer of cloud below 6000m covering more than half sky.___
A. roof
B. VFR Top
C. VMC
D. Ceiling
【单选题】
管制员在对空指挥过程中,应当主动地控制一句管制指令中所包含的管制指令的内容。一般情况下,管制员发布的一句管制指令中,包含的管制内容不应当超过___项
【单选题】
当观察到两个或多个雷达位置指示符相近,或观察到在同时作相似的移动以及遇到其它引起对目标怀疑的情况时,管制员应当___。
A. :根据进程单和现有雷达信息仍可以提供雷达管制服务
B. :向移交方了解是否是航空器的原因
C. :应当采用两种以上识别方法进行识别直至确认为止
D. :首先报告领班主任
【单选题】
“AIP”is“”___
A. Air Information Publication
B. Air traffic information Publication
C. Air traffic International Publication
D. Aeronautical Information Publication
【单选题】
An air show may with the consent of the______be the reason for an aerodrome being closed to all traffic for a few hours.___
A. Control tower
B. ACC
C. Approach Control
D. proper authorities
【单选题】
Who will be in charge for a flight?___
A. The first officer
B. The pilot-in-command
C. Fligh tattendant
D. Pilot
【单选题】
“APU”is______.___
A. a ground power facility
B. an air boarding facility
C. a hydraulic facility
D. a fueling facility
推荐试题
【单选题】
电池___后,总内阻等于各单个电池内阻之和。(易)
【单选题】
划线平台又称划线平板,用铸铁制成,它的上平面经过精刨或刮削,是划线的___平面。 (难)
【单选题】
平面划线是用划线工具将图样按实物___大小划到零件上去的。(中)
A. 1∶1
B. 1∶2
C. 1∶3
D. 1∶4
【单选题】
根据图样要求在毛坯或半成品上划出加工图形、加工界限或加工时找正用的辅助线称为___。( 易 )
【单选题】
锯削往复运动速度应控制在___次/min 左右。(难)
【单选题】
千分尺测微螺杆上的螺纹,其螺距为0.05 mm,当微分筒转一周时,测微螺杆就轴向移进___mm。(中)
A. 0.01
B. 0.02
C. 0.04
D. 0.05
【单选题】
游标卡尺的读数示值有___mm三种。( 易 )
A. 0.02、0.05、0.1
B. 0.2 、0.5 、1.0
C. 2、 5、 10
D. 20、50、100
【单选题】
用锉刀锉削时,使用的是锉刀的___部分。(难)
A. 锉刀面
B. 锉刀边
C. 锉刀舌
D. 锉刀底
【单选题】
按齿纹分为单齿纹和双齿纹。单齿纹锉刀的齿纹只有一个方向,与锉刀中心线成70°,一般用于锉___金属,如铜、锡、铅等。(难)
【单选题】
锉刀往复运动速度一般为___次/min,推出时慢,回程时可快些。(中)
A. 10~20
B. 20~30
C. 30~40
D. 40~50
【单选题】
钳工加工孔的方法一般指钻孔、扩孔和___。(中)
【单选题】
麻花钻由钻柄、颈部和___与切削部分组成。(易)
A. 导向部分
B. 头部
C. 旋转部分
D. 散热部分
【单选题】
孔径经钻孔、扩孔后,用铰刀对孔进行提高尺寸精度和表面质量的加工叫___。( 易)
【单选题】
由于螺纹的精度、___大小不同,丝锥一般为 1 支、2 支、3 支成组使用。( 中 )
【单选题】
当丝锥位置与螺纹底孔端面垂直后,轴向就不再加压力。两手均匀用力,为避免切屑堵塞,要经常倒转___圈,以达到断屑。(难)
A. 1/2~1/4
B. 1/3~1/5
C. 1/4~1/6
D. 1/5~1/7
【单选题】
攻铸铁材料螺纹时加___而不加切削液,钢件材料加切削液,以保证铰孔表面的粗糙度要求。(难)
【单选题】
焊接是指通过适当的物理化学过程如加热、加压或二者并用等方法,使两个或两个以上分离的物体产生原子(分子)间的___力而连接成一体的连接方法,是金属加工的一种重要工艺。(中)
【单选题】
电弧焊是利用电弧热源加热零件实现___焊接的方法。焊接过程中电弧把电能转化成热能和机械能,加热零件,使焊丝或焊条熔化并过渡到焊缝熔池中去,熔池冷却后形成一个完整的焊接接头。(中)
【单选题】
焊条电弧焊是用手工操纵___进行焊接的一种焊接方法,俗称手弧焊,应用非常普遍。(难)
【单选题】
焊接过程中,产生在焊条和零件之间的___将焊条和零件局部熔化,受电弧力作用,焊条端部熔化后的熔滴过渡到母材,和熔化的母材融合一起形成熔池,随着焊工操纵电弧向前移动,熔池金属液逐渐冷却结晶,形成焊缝。(中)
【单选题】
焊接时,焊芯有两个功能:一是传导焊接电流,产生电弧;二是焊芯本身熔化作为填充金属与熔化的母材熔合形成___。(难)
【单选题】
焊条药皮又称涂料,在焊接过程中起着极为重要的作用。它可以起到积极保护作用,利用药皮熔化放出的气体和形成的___,起机械隔离空气作用,防止有害气体侵入熔化金属。(中 )
【单选题】
焊条药皮的组成主要有稳弧剂、造气剂、造渣剂、脱氧剂、合金剂、粘接剂和___等。( 易 )
A. 增塑剂
B. 增强剂
C. 硬化剂
D. 塑化剂
【单选题】
焊条电弧焊有两种引弧方式:划擦法和___法。( 难 )
【单选题】
焊条电弧焊是依靠人手工操作焊条运动实现焊接的,此种操作也称___。(中)
【单选题】
常见的焊条电弧焊运条方法有___种。(易)
【单选题】
为不影响焊缝成形,保证接头处焊接质量,更换焊条的动作越快越好,并在接头弧坑前约 ___ mm处起弧,然后移到原来弧坑位置进行焊接。(中)
【单选题】
焊缝的收尾操作时,应保持正常的熔池温度,做无直线运动的横摆点焊动作,此外还有三种焊缝收尾的操作方法,即___收尾法、反复断弧收尾法和回焊收尾法,也在实践中常用。(难)
【单选题】
在实际生产中,由于焊接结构和零件移动的限制,焊缝在空间的位置除平焊外,还有立焊、横焊、仰焊。其中焊接条件___位置最差。(中)
【单选题】
电弧焊机行走机构:是使焊接机头和零件之间产生一定速度的相对运动,以完成___焊接过程的机械装置。(中)
【单选题】
接头形式电阻焊可分成点焊、缝焊、凸焊和___四种。(中)
【单选题】
缝焊一般应用在有密封性要求的接头制造上,适用材料板厚为___ mm,如汽车油箱、暖气片、罐头盒的生产。(难)
A. 0.1~0.02
B. 0.1~0.2
C. 0.1~2
D. 0.1~20
【单选题】
工件焊后一般都会产生变形,如果变形量超过___值,就会影响使用。( 中 )
【单选题】
焊接变形产生的主要原因是___不均匀地局部加热和冷却。(中)
【单选题】
焊接产生拉应力和压应力,当这些应力超过金属的___极限时,将产生焊接变形;当超过金属的强度极限时,则会出现裂缝。(难)
【单选题】
焊瘤对静载强度无影响,但会引起应力集中,使___强度降低。(难)
【单选题】
焊缝的外部缺陷五种:焊缝增强过高,焊缝过凹,焊缝咬边,___,烧穿。(难)
A. 焊缝开裂
B. 焊缝过高
C. 塌陷
D. 焊瘤
【单选题】
焊缝中熔入过多的___,也会引起冷裂纹。(难)
【单选题】
焊接质量的检验包括___试验三个方面。这三者是互相补充的,而以无损探伤为主。(中)
A. 外观检查、无损探伤和仪器检测
B. 内观检查、无损探伤和机器检测
C. 外部检查、无损探伤和机械性能
D. 内部检查、无损探伤和机械性能