【单选题】
区域管制中心雷达管制间隔使用规定中,除逆向飞行之外,两架航空器在建立规定的垂直间隔以前,水平间隔不得小于___千米
查看试卷,进入试卷练习
微信扫一扫,开始刷题
相关试题
【单选题】
当区域范围外发生大面积航班备降,需安排航班在广州区域范围内等待时,于国际飞越航班,应尽量安排其___。
A. 立即等待
B. 就近备降
C. 至目的地较近的扇区等待
D. 联系接受单位问清具体情况
【单选题】
根据《空中交通管制中心航班备降运行保障程序》处置航班备降时的总体原则,___对备降及备降场选择承担主体职责。
A. 管制员
B. 机场运控部门
C. 航空公司运控部门
D. 机长
【单选题】
下列关于备降的处置要求,说法错误的是哪一项?___
A. 航班决定备降时,以机组的最终决定为决断点。
B. 区域内某一机场已宣布不接受备降,如在外区域依然有航班执意前外备降,可以拒绝接受此类航班进入广州区域。
C. 机组宣布NOTAM明确不能接收航班备降的机场备降,可以向机组说明情况,但最终是否前往由机组决定。
D. 广州区域内发生大面积航班备降情况时,对于未进区域的航班,可以根据区域相关扇区通行能力尽早给出预计进区域时间,必要时可要求相邻管制单位建议机组早作决定,并尽量选择区域外的备降场备降。
【单选题】
发生在管制中心范围以外,需要进入管制中心范围的紧急备降,助理管制席位的处置措施说法错误的是哪一项?___
A. 了解该航空器所处状态和飞行员意图,以及相邻管制单位已经或即将采取的引导措施。
B. 立即向相关运行领班通报,并向相关军民航管制单位/扇区通报并协调避让措施。
C. 将相关情况及协调结果通报指挥席位。
D. 将相关情况及协调结果通报流量分析室,由其负责对外通报。
【单选题】
下列针对非紧急备降情况时,管制席位的处置措施说法错误的是哪一项?___
A. 向机组了解航空器状态、备降原因及落地后是否需要其他协助等信息,并告知助理席位。
B. 天气原因备降时,将所了解到的目的地机场运行状况,如机场关闭或低于运行标准、预计持续时间等信息及时通报相关机组。
C. 若机组所选择的备降机场因NOTAM明确不能接收航班备降时,要球机组更改备降场。
D. 如果确需延误,尽早向机组通报预计需要延误的时间,防止其他紧急情况的发生。
【单选题】
当值班人员认为紧急频率121.5MHz有干扰并影响正常工作时,可以向___申请临时暂停紧急频率121.5MHz的守听。
A. 管制席位
B. 科室领班主任
C. 区管总领班
D. 管制中心总领班
【单选题】
守夜期间,每一段班中,管制员连续在EC实施对空指挥时间不得超过___。
A. 1小时30分钟
B. 2小时
C. 3小时
D. 4小时
【单选题】
在聘期内发生本人原因造成的严重差错(含)以上的工作差错或发生___次(含)以上的一般差错者,将取消岗位教员资格。
【单选题】
_____carpet maybe required for emergency landing. ___
A. Water
B. Foam
C. Rubber
D. Sand
【单选题】
ADS is a means for_____.___
A. control
B. communication
C. navigation
D. Surveillance
【单选题】
Before providing radar service,air traffic controllers hould______to the aircraft. ___
A. confirm altitude
B. confirm identity
C. confirm speed
D. confirm heading
【单选题】
Because of their high fuel consumption at low levels,______prefer to remain at higher altitudes when they fly. ___
A. light and small aircraft
B. propeller aircraft
C. Jets
D. allaircraft
【单选题】
When an aircraft was in emergency after taking off,i tshould______before landing. ___
A. check the engine
B. read the checklist
C. dumpfuel
D. makeaplan
【单选题】
“Engine flamed out“means______.___
A. Engine failure
B. Engine fire
C. Engine started
D. Engine lost
【单选题】
“Encounter”means_________
A. spend
B. meet
C. counter
D. get
【单选题】
The opposite meaning of“converging”is______.___
A. diverging
B. opposite
C. diverting
D. closing
【单选题】
Which of the following is not included in the ATC clearance? ___
A. Aircraft callsign
B. Flight route
C. Wind direction and speed
D. Clearance limit
【单选题】
“Recycle squawk A0612”means______.___
A. reselect squawk number A0612
B. don’t use A0612
C. who is squawking A0612
D. squawk A0612
【单选题】
“A575”is a name of a route.“A”means_________
A. the order
B. the first kind
C. main south and north direction
D. no special meaning
【单选题】
“FMC”is a system in an aircraft to manage the______.___
A. met message
B. flight data
C. flight pitch
D. flight roll
【单选题】
“Deteriorating weather”means the weather is getting______.___
A. better
B. clear
C. good
D. worse
【单选题】
Azimuth means horizontal______or direction. ___
A. heading
B. direction
C. bearing
D. scale
【单选题】
According to characters and conditions of flights on the route,ATS route is divided into______and______route. ___
A. domestic,international
B. fixed,temporary
C. regional,national
D. civil,military
【单选题】
Fuel______means the quantity of fuel carried by now. ___
A. reminding
B. endurance
C. number
D. total
【单选题】
The opposite meaning of“speedup”is_________
A. slowdown
B. speeddown
C. speedlow
D. slowby
【单选题】
Pilot turns on squawk______to request a squawk number. ___
A. 3000
B. 3500
C. 4000
D. 2000
【单选题】
First______assistance means doctor and ambulance in an emergency condition. ___
A. emergency
B. priority
C. aid
D. help
【单选题】
When somebody is reported hurt on board,maybe it will need______assistance on arrival. ___
A. fire-cart
B. medical
C. police
D. wheelchair
【单选题】
In emergency descent procedure,the pilot should turn right______out of the route while descending. ___
A. 40°
B. 30°
C. 20器
D. 15°
【单选题】
管制员在对空指挥过程中,越是繁忙的时候,语速应___
A. 保持平稳,避免频繁重复指令
B. 尽量快些,才能指挥更多飞机
C. 降低语速,避免口误
D. 时快时慢,引起机组的注意
【单选题】
According to ICAO,a standard holding pattern should all turn to the______.___
A. right
B. west
C. left
D. east
【单选题】
The standard altimeter setting is______inhpa. ___
A. 1013.20062
B. 1010.10062
C. 29.92002
D. 30.10002
【单选题】
2500f/m rate of vertical speed is equal to______.___
A. 10m/s
B. 15m/s
C. 20m/s
D. 25m/s
【单选题】
陆空通话时,什么时候推荐使用“IMMEDIATELY(立即)”这个词:___
A. 相对飞行穿高度时
B. 天气差时,担心自己会忘记某个正在改变高度的动态
C. 飞机多时,为了节省精力
D. 在紧急情况下,用于冲突解脱时
【单选题】
Standard rate for a turning is______degrees per second. ___
【单选题】
What is the best course of action for a pilot to follow when thunderstorms are observed along the route of flight? ___
A. Fly below the thunderstorms
B. Climb over the thunderstorms
C. Disregard the thunderstorms
D. Take any action to avoid all thunderstorms
【单选题】
The subdivision of frequencies is______MHZ. ___
A. 0.025
B. 0.035
C. 0.02
D. 0.015
【单选题】
Aeronautical chart is divided into two categories,______. ___
A. Aeronautical map and special type of aeronautical chart
B. En-route chart and approach chart
C. Area chart and standard instrument arrival and departure chart
D. Aerodrome chart and area chart
【单选题】
Aircraft are required to comply with ATC instructions within______.___
A. advisory airspace
B. domestic airspace
C. controlled airspace
D. international airspace
【单选题】
Amendments to the initial clearance will be issued at anytime an air traffic controller deems such action necessary to______.___
A. avoid possible confliction between aircraft
B. correct the previously issued clearance
C. cancel the flight plan
D. expedite the traffic
推荐试题
【单选题】
___是珠光体耐热钢的主要合金元素
A. Cr和Ni
B. Cr和Mo
C. Mn和Mo
D. Ni和MO
【单选题】
珠光体耐热钢的焊接性主要是易产生___
A. 冷裂纹和再热裂纹
B. 冷裂纹和应力腐蚀
C. 热裂纹和晶间腐蚀
D. 热裂纹和应力腐蚀
【单选题】
珠光体耐热钢焊条是根据母材的___来选择的
A. 力学性能
B. 高温强度
C. 化学成分
D. 使用温度
【单选题】
牌号为R317的焊条是___焊条
A. 低温钢
B. 结构钢
C. 奥氏体不锈钢
D. 珠光体耐热钢
【单选题】
珠光体耐热钢焊前局部预热必须保证预热宽度,焊缝两侧各大于所焊壁厚的4倍,且至少不小于 ___mm
A. 100
B. 150
C. 200
D. 250
【单选题】
珠光体耐热钢焊条电弧焊焊后应立即进行___
A. 高温回火
B. 低温回火
C. 退火
D. 正火
【单选题】
牌号为W707的焊条是___焊条
A. 结构钢
B. 低温钢
C. 奥氏体不锈钢
D. 奥氏体耐热钢
【单选题】
___不是用于-40~-100℃的低合金低温钢焊接工艺特点
A. 一般可不预热
B. 焊前预热
C. 耍控制层间温度不大于200~300℃
D. 焊后进行热处理,细化晶粒消除应力
【单选题】
2Cr13钢是___型不锈钢
A. 马氏体
B. 铁素体
C. 奥氏体
D. 奥氏体-铁素体
【单选题】
奥氏体不锈钢的电阻率___
A. 比碳钢低
B. 比碳钢高
C. 与碳钢一样
D. 略低于碳钢
【单选题】
加热温度 ___℃是不锈钢晶间腐蚀的危险温度区,或称敏化温度区
A. 150-450℃
B. 450-850℃
C. 850-950℃
D. 950-1050℃
【单选题】
超低碳奥氏体不锈钢碳的质量分数为≤___
A. 0.14%
B. 0.08%
C. 0.06%
D. 0.03%
【单选题】
___不是奥氏体不锈钢焊接时为减小焊接残余应力采取的工艺措
A. 采用小线能量
B. 焊前预热
C. 采用短焊道焊
D. 适当的焊后锤击施
【单选题】
___不是奥氏体不锈钢焊接时防止热裂纹的措施
A. 严格限制焊缝中硫、磷等杂质的质量分数
B. 选用双相组织的焊条
C. 采用小线能量,多层多道焊
D. 选用酸性焊条
【单选题】
___不是奥氏体不锈钢的焊接工艺特点
A. 不能进行预热和后热工艺
B. 采用小线能量,小电流快速焊
C. 要快速冷却
D. 焊前预热
【单选题】
___不是奥氏体不锈钢焊条电弧焊工艺操作必须遵循的原则
A. 选用碱性焊条,采用直流反接
B. 采用多层多道焊
C. 采用焊条不摆动的窄道焊
D. 控制焊道间温度,冷却到60℃左右再焊下一道
【单选题】
焊接热裂纹可看成是拉应力和___两者联合作用而形成的
A. 低熔点共晶
B. 氢
C. 淬硬组织
D. 氮化物
【单选题】
___不是促成冷裂纹的主要因素
A. 钢种淬硬倾向大,产生淬硬组织
B. 接头受到的拘束应力大
C. 较多扩散氢的存在和聚集
D. 较多氧的存在和聚集
【单选题】
按规定参数烘干焊条、焊剂是防止 ___的措施之一
A. 夹渣
B. 气孔
C. 热裂纹
D. 未焊透
【单选题】
工件表面锈皮未清除干净会引起___
A. 气孔
B. 再热裂纹
C. 咬边
D. 弧坑
【单选题】
___不是产生夹渣的原因
A. 焊层、焊道之间清渣不干净
B. 焊接电流太小
C. 焊接速度太快
D. 未按规定参数烘干焊条、焊剂
【单选题】
___不是产生未焊透的原因
A. 坡口钝边过大,间隙太小
B. 焊接电流过小,焊接速度过快
C. 短弧焊接
D. 焊接时电弧磁偏吹
【单选题】
钨极直径太小、焊接电流太大是产生 ___的原因之一
A. 夹钨
B. 热裂纹
C. 再热裂纹
D. 未焊透
【单选题】
下列缺陷一般除___外,均需进行返修
A. 焊缝表面有裂纹
B. 焊缝内部有超过图样和标准规定的缺陷
C. 焊缝表面有气孔、夹渣
D. 深度不大于0.5mm、连续长度不大于100mm的咬边
【单选题】
___不是焊接检验的目的
A. 发现焊接缺陷
B. 检验焊接接头的性能
C. 确保产品的焊接质量
D. 测定焊接残余应力
【单选题】
___不是非破坏性检验
A. 致密性试验
B. 水压试验
C. 着色检验
D. 金相检验
【单选题】
___不属于破坏性检验
A. 水压试验
B. 弯曲试验
C. 冲击试验
D. 耐腐蚀试验
【单选题】
在射线探伤胶片上呈圆形、椭圆形黑点,其黑度一般是中心处较大并均匀地向四周边缘减小的缺陷是___
【单选题】
在射线探伤胶片上呈单独黑点,外形不太规则,带有棱角,黑度较均匀的缺陷是___
A. 点状夹渣
B. 条状夹渣
C. 气孔
D. 未熔合
【单选题】
我国射线探伤标准规定,焊缝质量分为四个等级, ___是1级焊缝内允许存在缺陷
A. 气孔
B. 未熔合
C. 未焊透
D. 条状夹渣
【单选题】
我国射线探伤标准规定,焊缝质量分为四个等级,___是2级焊缝内允许存在的缺陷
【单选题】
单相桥式可控整流电路电感性负载时,控制角α的移相范围是___。
A. 0~90°
B. 0~360°
C. 0~180°
D. 0~270°
【单选题】
单相桥式可控整流电路电阻性负载,晶闸管中的电流平均值是负载的___倍。
【单选题】
晶闸管两端并联压敏电阻的目的是实现___。
A. 过压保护
B. 过流保护
C. 防止冲击电流
D. 防止冲击电压
【单选题】
断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大过载电流
B. 最大短路电流的
C. 最大允许电流
D. 最大负载电流
【单选题】
接触器的额定电压应不小于主电路的___。
A. 短路电压
B. 工作电压
C. 最大电压
D. 峰值电压
【单选题】
对于工作环境恶劣、启动频繁的异步电动机,所用热继电器热元件的额定电流可选为电动机额定电流的___倍。
A. 0.95~1.05
B. 1.05~1.15
C. 1.15~1.50
D. 0.85~0.95
【单选题】
中间继电器的选用依据是控制电路的___、电流类型、所需触点的数量和容量等。
A. 电压等级
B. 阻抗大小
C. 短路电流
D. 绝缘等级