【填空题】
73.通过显示黄色灯光的信号机及位于定位的预告信号机时，列车运行限制速度为在___信号机前能停车的速度。
查看试卷，进入试卷练习
微信扫一扫，开始刷题
相关试题
【填空题】
74.向站内有车线接车时，列车应在进站信号机外停车，由接车人员向司机通知事由后，以___将列车领入站内。
【填空题】
75.列车进站后，应停于接车线___内方。在设有出站【进路】信号机的线路，列车头部不得越过出站【进路】信号机。
【填空题】
76.货物列车在站停车时，司机必须使列车保持___状态。
【填空题】
77.货物列车在站停车时，司机必须使列车保持制动状态【铁路局指定的凉闸站除外】。发车前，司机施行缓解，确认___具备后，方可起动列车。
【填空题】
78.列车在车站发车前，司机必须确认___及发车信号显示正确后，方可起动列车。
【填空题】
79.进站信号机及线路所通过信号机发生不能关闭的故障时，应将灯光熄灭或___。
【填空题】
80.装有进路表示器或发车线路表示器的出站信号机，当该表示器不良时，由办理发车人员通知司机后，列车可凭___的显示出发。
【填空题】
81.列车在区间被迫停车不能继续运行时，司机应立即使用列车无线调度通信设备通知两端站(列车调度员)及车辆乘务员(随车机械师)，报告___和停车位置，根据需要迅速请求救援。
【填空题】
82.对已请求救援的列车，不得再行移动，并按规定对列车进行___。
【填空题】
83.列车分部运行，机车进入区间挂取遗留车辆时，应从车列前方距离不小于___米处防护。
【填空题】
84.一切电话中断后发出的列车(持有附件3通知书1的列车除外)，应于停车后，立即从列车___按线路最大速度等级规定的列车紧急制动距离位置处防护。
【填空题】
85.在不得已情况下，列车必须分部运行时，司机应报告前方站(列车调度员)，并做好遗留车辆的___和防护工作。
【填空题】
86.列车发生火灾、爆炸时，须立即停车,停车地点应尽量避开___、长大隧道等，选择便于旅客疏散的地点。
【填空题】
87.列车运行途中司机接到因热轴需停车检查的通知后，应采用___停车，列车停车后由车辆乘务员负责检查，无车辆乘务员的由司机确认能否继续安全运行，或就近站甩车处理。
【填空题】
88.向封锁区间开行救援列车时，司机接到救援命令后，必须认真确认，命令不清、___不明确时，不准动车。
【填空题】
89.遇有施工引导接车并正线通过时，准许列车司机凭___手信号的显示，以不超过60km/h速度进站。
【填空题】
90.向施工封锁区间开行路用列车时，列车进入封锁区间的行车凭证为___。
【填空题】
91.路用列车应由施工单位指派胜任人员携带列车无线调度通信设备值乘，并在区间协助___作业。
【填空题】
92.路用列车或施工机械进入施工地段时，应在施工防护人员显示的停车手信号前停车，根据施工负责人的要求，按___办法，进入指定地点。
【填空题】
93.列车接近作业标时，司机须___，注意瞭望。
【填空题】
94.站内线路、道岔发生故障时，应按规定设置___信号防护。
【填空题】
95.线路发生故障时，如设有固定信号机，应先使其显示___信号。
【填空题】
96.信号是指示___及调车作业的命令，有关行车人员必须严格执行。
【填空题】
97.铁路信号分为视觉信号和___信号。
【填空题】
98.铁路视觉信号中黄色的含义是___或减低速度。
【填空题】
99.出站信号机以显示___信号为定位。
【填空题】
100.集中联锁车站的进站、进路、出站信号机，通过信号机，当机车或车辆___越过该信号机后自动关闭。
【填空题】
101.进站信号机的灯光熄灭、显示不明或显示不正确时，视为___信号。
【填空题】
103.三显示自动闭塞区段，进站色灯信号机显示一个黄色灯光时，准许列车经道岔___位置，进入站内正线准备停车。
【填空题】
104.三显示自动闭塞区段的进站色灯信号机显示两个黄色灯光，准许列车经道岔___位置，进入站内准备停车。
【填空题】
105.四显示自动闭塞区段，进站色灯信号机显示一个___灯光时，准许列车按限速要求经道岔直向位置进入站内正线准备停车。
【填空题】
106.四显示自动闭塞区段的进站色灯信号机显示一个绿色灯光，准许列车按规定速度经道岔直向位置进入或通过车站，表示运行前方至少有___闭塞分区空闲。
【填空题】
107.接车进路信号机的引导信号显示一个红色灯光及一个月白色灯光——准许列车在该信号机前方不停车，以不超过___km/h速度通过接车进路，并须准备随时停车。
【填空题】
108.自动站间闭塞区段，出站色灯信号机显示两个绿色灯光时，准许列车由车站出发，开往___。
【填空题】
109.自动闭塞区段，出站色灯信号机显示___灯光，准许列车由车站出发，开往半自动闭塞或自动站间闭塞区间。
【填空题】
110.三显示自动闭塞区段，出站色灯信号机显示一个绿色灯光，准许列车由车站出发，表示运行前方至少有___闭塞分区空闲。
【填空题】
111.四显示自动闭塞区段，出站色灯信号机显示一个绿色灯光和一个黄色灯光，准许列车由车站出发，表示运行前方有___闭塞分区空闲。
【填空题】
112.四显示自动闭塞区段出站色灯信号机显示一个黄色灯光，准许列车由车站出发，表示运行前方有___闭塞分区空闲。
【填空题】
113.四显示自动闭塞区段，通过色灯信号机显示一个绿色灯光，准许列车按规定速度运行，表示运行前方至少有___闭塞分区空闲。
推荐试题
【判断题】
在机械设备中，凸轮表面误差将会引起扭转振动
【单选题】
What happens to the status of users already logged into ESXi Shell when a vSphere administrator enables lockdown mode?___
A. Users remain logged in and can run commands, except to disable lockdown mode.
B. Users remain logged in and can run commands, including disabling lockdown mode.
C. Users are immediately logged out of ESXi Shell.
D. Users are logged out after a timeout specified by the vSphere administrator.
【单选题】
What is the effective vSphere licensing level during the 60 day evaluation period?___
A. vSphere Foundation Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
【单选题】
To comply with security requirements, an administrator with a vCenter Server Appliance needs to force logoff of the vSphere web client after 10 minutes of inactivity.What should the administrator do to meet the requirement?___
A. Edit: /var/lib/vmware/vsphere-client/webclient.properties, modify session.timeout=10
B. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=600
C. Edit: /var/lib/vmware/vsphere-client/webclient.properties modify session.timeout=600
D. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=10
【单选题】
An administrator enables High Availability (HA) on a Virtual SAN cluster.Which network is used for HA Network Heatbeat configuration?___
A. The Management network.
B. The vMotion network.
C. The Virtual SAN network.
D. The Provisioning Traffic network.
【单选题】
A user wants to monitor a business-critical virtual machine to ensure that it doesn't run out of resources. What metric could be monitored in vRealize Operations to address this concern?___
A. Time Remaining badge
B. Compliance badge
C. Reclaimable Waste badge
D. Density badge
【单选题】
An administrator has recently installed a new ESXi 6.x Host, and during the configuration notices sporadic network problems. To check whether the issue occurred sometime during the configuration, the administrator would like to reset the system.How can this be accomplished in the shortest amount of time?___
A. Run the ESXi installer again and reinstall the host.
B. Select the Reset System Configuration option from the vSphere Client when connected directly to the host.
C. From the
D. irect Console User Interface, select Reset System Configuration.
【单选题】
A vApp is running out of compute resources when overall activity is high within the resource pool. At other times, everything is fine.What should be done to resolve this issue?___
A. Increase the size of the resource pool Shares.
B. Set the vApp's CPU and Memory Reservation Type to Expandable.
C. Set the vApp's CPU and Memory Limit to Unlimited.
D. Create a new resource pool with the existing hardware configuration.
【单选题】
A virtual machine has been renamed and an administrator is unable to find files with the new virtual machine name in the datastore.What is the reason for this?___
A. The names of the files on the datastore do not change.
B. The names of the files on the datastore have been corrupted.
C. The virtual machine needs to be re-added to the inventory.
D. The Distributed Resource Scheduler moved the virtual machine to another host.
【单选题】
An administrator has configured network connectivity for a new virtual machine, as shown in the Exhibit.What will occur with the network traffic of this virtual machine when communicating externally from vSwitch1?___
A. The virtual machine will communicate on both uplinks
B. The virtual machine will only communicate on vmnic1
C. The virtual machine will only communicate on vmnic2
D. The virtual machine will fail to communicate externally
【单选题】
An administrator is unable to create the first group in a new vRealize Operations environment. What is the likely cause of the problem?___
A. There are no group types defined.
B. The group is not defined in SSO.
C. There are more than 32 group types defined.
D. The description for the group is not provided.
【单选题】
A new vApp was built and tested in the corporate headquarters datacenter running vSphere 6.x. What condition would explain why the virtual machine is failing to boot in an offsite datacenter running on vSphere 5.5?___
A. The virtual machine was built with the default hardware version.
B. The VMFS 5 datastore is not compatible with virtual machines configured with vSphere 6.x.
C. a
D. RS 5.5 cluster cannot run virtual machines configured with vSphere 6.x.
【单选题】
An administrator is evaluating whether to deploy vCenter Server on a Windows server or on a vCenter Server appliance. The administrator has the following requirements: <A web browser will be utilized to manage the vSphere environment.> <16 ESXi hosts will be deployed.> <Licenses must be shared with a vCenter Server at another site.> <An external Oracle 10g database server will be used to host the vCenter Server database.> Why will the administrator need to deploy vCenter Server on a Windows server?___
A. Linked Mode is a requirement for the solution.
B. Oracle 10g is a requirement for the solution.
C. The vSphere web client is a requirement for the solution.
D. Management of more than 5 hosts is a requirement for the solution.
【单选题】
What is a benefit of using VMware Data Protection ?___
A. Provides support for guest-level backups and restores of Microsoft SQL Servers, Exchange Servers, and Share Point Servers.
B. Provides support for advanced storage services including replication, encryption, deduplication, and compression.
C. Provides direct access to VDP configuration integrated into the vSphere Client.
D. Reduces disk space consumed by virtual machine data using deduplication.
【单选题】
An administrator enables vSphere High Availability (HA) on an existing cluster with a large number of hosts and virtual machines. The administrator notices that the setup of vSphere HA on some of the hosts is failing. What step, if taken, might resolve this issue?___
A. Increase the value of the config.vpxd.das.electionWaitTimeSec setting.
B. Set the value of vpxd.das.aamMemoryLimit to 256.
C. Set the value of the das.useDefaultIsolationAddress setting to False.
D. Increase the value of the das.iostatsinterval setting.
【单选题】
An ESXi 6.x host consists of 24 logical cores. Hyperthreading is enabled on the host. What is the maximum number of vCPUs that can be assigned to a virtual machine on this host?___
【单选题】
By default, each ESXi 6.x host is provisioned with a certificate from which root certificate authority?___
A. RedHat Certificate Authority
B. VMware Certificate Authority
C. DigiCert Certificate Authority
D. Verisign Certificate Authority
【单选题】
An administrator is adding an NFS datastore as shown in the Exhibit. What is the purpose of the Servers to be added list?___
A. It contains the IP addresses of the NFS Storage Server to provide multipathing capability.
B. It contains the IP addresses of the ESXi hosts that mount the datastore.
C. It contains the IP addresses used for
D. ynamic Discovery of targets.
【单选题】
An administrator reports that the System Event log data is only available for 24 hours when reviewing the Hardware Status tab. Which condition could be responsible for the loss of data?___
A. A Reset event log was executed.
B. The statistical collection level was set to a value of 1.
C. The boot disk of the host is corrupt.
D. Syslog has been configured at the vCenter Server level.
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
