【填空题】
55.应急电源输出电压低应如何处理?*简答题*___
查看试卷,进入试卷练习
微信扫一扫,开始刷题
处理方法:首先检查电源箱三相电压是否正常,之后检查变压器B2初级三相电源是否缺相,如缺相检查引线是否脱落、变压器接线是否脱掉、输入接线排处是否缺相。如以上正常,检查输出电流,如输出电流过大,说明负载超载,应减载。检查变压器B2次级输出电压,空载时约为40.3V,满载时约为38V,如变压器次级输出电压正常,检查整流模块V2,断电将V2从电路中拆开,用万用表测量V2内部二极管是否有断路。
相关试题
【填空题】
56.DC600V供电列车司机反映无供电集控器电源,应如何处理?*简答题*___
【填空题】
57.当塞拉门出现锁闭装置不能二级锁闭时应如何处理?*简答题*___
【填空题】
58.运用中的蓄电池遇到哪些情需施行补充电或个别修换?*简答题*___
【填空题】
59.什么叫铅蓄电池的放电最终电压?一般规定是多少?*简答题*___
【填空题】
60.什么叫发电机运行中特性?它包括哪些内容?*简答题*___
【填空题】
61.晶闸管对触发电路有哪些要求?*简答题*___
【填空题】
62.空调机组电气控制电路中有哪些保护装置?*简答题*___
【填空题】
63.客车发电机传动装置的段修应符合哪些要求?*简答题*___
【填空题】
64.制冷效果不好如何处理?*简答题*___
【填空题】
65.交流接触器在运行中有时产生噪声,是什么原因?*简答题*___
【填空题】
66.旅客到列车在运行过程中,全列临时灭灯时该如何查找故障?*简答题*___
【填空题】
67.运转中空调机组突然停机的主要原因有哪些?*简答题*___
【填空题】
68.电茶炉开关置于“通”位后,加热和缺水指示灯均不亮,接触器不吸合如何处理?*简答题*___
【填空题】
69.容量7千瓦以上的交流感应电动机为什么要采取降压启动?*简答题*___
【填空题】
70.客车空调使用最多的制冷压缩机是何种形式?*简答题*___
【单选题】
列车停留超过_____时,列车自动制动机需做简略试验。___
A. 10min
B. 15min
C. 20min
D. 30min
【单选题】
列车中相互连挂的车钩中心水平线的高度差,不得超过_____。___
A. 60mm
B. 70mm
C. 75mm
D. 80mm
【单选题】
最高运行速度120km/h的旅客列车,紧急制动距离限值为_____。___
A. 2000m
B. 1400m
C. 1100m
D. 800m
【单选题】
最高运行速度160km/h以上至200km/h的旅客列车,紧急制动距离限值为_____。___
A. 2000m
B. 1400m
C. 1100m
D. 800m
【单选题】
我国规定_____以下的电压为安全电压。___
A. 36V
B. 48V
C. 110V
D. 220V
【单选题】
通过电气化铁路平交道口的机动车辆及运输工具,所装载的货物高度[从地面算起,下同]不得超过_____或触及道口限界门的吊标[吊链、横板]。___
A. 4m
B. 4.5m
C. 6m
D. 10m
【单选题】
二氧化碳[干粉]灭火器适用于扑灭_____以下的各种电器火灾。___
A. 2000V
B. 1000V
C. 800V
D. 600V
【单选题】
在电气化铁路附近施工、冲洗车辆时,保持水流与接触网带电部分有_____以上距离,防止触电事故发生。___
A. 1m
B. 2m
C. 0.5m
D. 2.5m
【单选题】
在客车制动机单车试验时,单车试验器的单车风压应调整到_____。___
A. 400kPa
B. 500kPa
C. 600kPa
D. 700kPa
【单选题】
低压是指对地电压在_____及以下的电压。___
A. 250V
B. 500V
C. 800V
D. 1000V
【单选题】
电气化铁路开通后,_____要对从业人员进行电气化铁路安全知识的培训和考试。___
A. 每月
B. 每季度
C. 每年
D. 每两年
【单选题】
在电气化铁路区段的列检,乘务员及车辆检修设备作业人员携带的任何物件与接触网设备的带电部分应保持_____以上距离。___
A. 1m
B. 1.5m
C. 2m
D. 2.5m
【单选题】
接触网导线折断下垂搭在车辆上或其他物品与接触接网接触时,列检和乘务人员不要进行处理,应保持_____以上距离,同时对现场进行防护,并及时通知有关人员查处。___
【单选题】
在电气化线路上,严禁攀登车辆顶部进行_____等作业。___
A. 转向架检修
B. 轮对检修
C. 空调机组检修
D. 车钩检修
【单选题】
在电化区段雨天作业人员要穿雨衣,禁止使用_____,不准在支柱下、机车、车辆下避雨。___
A. 口罩
B. 浸塑手套
C. 雨伞
D. 胶鞋
【单选题】
采用密接式车钩的旅客列车,因故更换15号过渡车钩与机车连接时应限速运行,运行速度不得超过________
A. 140km/h
B. 160km/h
C. 150km/h
D. 200km/h
【单选题】
运用列车质量鉴定时,列车等级分四档,A级列车为_____。___
A. 800~899分
B. 900~1000分
C. 700~799分
D. 600~699分
【单选题】
使用空调机组空气预热器时,须先开启通风机运行;停用时,须先关闭空气预热器,_____后方准关闭通风机。___
A. 5min
B. 8min
C. 10min
D. 15min
【单选题】
跨局直通旅客列车每运行一个往返必须安排入库检修,单程运行距离在_____及以上的旅客列车,在折返站原则上应安排入库检修。___
A. 4000km
B. 3000km
C. 2000km
D. 1000km
【单选题】
临修客车处理故障的时间原则上不得超过________
A. 12h
B. 24h
C. 36h
D. 48h
【单选题】
第10版《铁路技术管理规程》[铁道部令第29号]自_____起施行。___
A. 2006年10月1日
B. 2007年1月1日
C. 2007年4月1日
D. 2006年10月25日
【单选题】
列车机车与第一辆车电气连接线的连接与摘解由客列检作业人员负责,无客列检作业人员时,由_____负责。___
A. 列检人员
B. 机车乘务员
C. 车辆乘务员
D. 车站人员
【单选题】
密接式车钩的客车回送时,原则上应附挂旅客列车回送,附挂货物列车回送时,应挂于_____,但不得超过2辆。___
A. 头部
B. 尾部
C. 中部
D. 任何部位
【单选题】
旅客站台分为低站台、高站台,低站台高度为300mm,500mm,高站台高度为_____。___
A. 600mm
B. 800mm
C. 1100mm
D. 1250mm
【单选题】
列车在区间被迫停车后,对于邻线上妨碍行车地点,应按下列规定放置响墩防护:从两方面_____处防护,如确知列车开来方向时,仅对来车方面防护。___
A. 不少于300m
B. 不少于800m
C. 不少于1000m
D. 按线路最大速度等级规定的列车紧急制动距离位置
推荐试题
【单选题】
Which port is used for communication between ESXi and vSphere Data protection?___
A. 80
B. 443
C. 902
D. 22
【单选题】
What can prevent Storage DRS from functioning on a datastore?___
A. The datastore is configured for Virtual Machine Swapfile location.
B. The datastore is shared across multiple datacenters.
C. The datastore is connected to a host that is running Storage I/O Control.
D. Storage DRS advanced option IgnoreAffinityRulesForMaintenance is set to 1.
【单选题】
When troubleshooting VMware vCenter Server issues, when logging level provides maximum detail?___
A. Verbose
B. Trivia
C. Info
D. Error
【单选题】
What new feature is introduced in NFS 4.1 on ESXi 6.5?___
A. IPv6
B. KRB5i
C. AUTH_SYS
D. Storage DRS
【单选题】
What configuration option would ensure that a virtual NUMA topology is defined on VMs having more than eight virtual CPUs?___
A. cupid.coresPerSocket
B. numa.vcpu.followcorespersocket
C. numa.vcpu.maxPerVirtualNode
D. numa.vcpu.min
【单选题】
What is the minimum disk space required to deploy vSphere Data Protection (VDP) with 8 TB configuration?___
A. 4 TB
B. 16 TB
C. 8 TB
D. 12 TB
【单选题】
What advanced option for vSphere HA defines a maximum number of reset attempts by VMCP for a virtual machine?___
A. das.maxterminates
B. das.isolationshutdowntimeout
C. das.maxresets
D. fdm.isolationpolicydelaysec
【单选题】
What vSphere technology enables the administrator to ensure consistent configuration at scale?___
A. PowerCLI
B. Host Profiles
C. esxcli
D. vSphere Web Client
【单选题】
Which port is used for vSphere HA agent-to-agent communication?___
A. 443
B. 8182
C. 22
D. 902
【单选题】
Which log file would assist in identifying an issue that occurred during the database export phase of a vCenter Server upgrade process?___
A. vcdb_import.out
B. export.json
C. export-upgrade-runner.log
D. vcdb_export.out
【单选题】
Bidirectional CHAP is support by which storage initiator?___
A. software FCoE HBA
B. Fibre Channel HBA
C. independent hardware iSCSI HBA
D. dependent hardware iSCSI HBA
【单选题】
What is a pool of raw storage capacity that a storage system can provide to Virtual Volumes?___
A. protocol endpoint
B. storage container
C. storage provider
D. datastore
【单选题】
vSphere 6.5 DRS is now Network-Aware. Based on network utilization, when will DRS balance VMs?___
A. DRS will balance VMs when a network resource pool is configured for VMs.
B. DRS will balance VMs when Network I/O Control is enabled.
C. DRS will place VMs on initial boot for hosts that have network utilization lower that the threshold.
D. DRS will vMotion VMs when network utilization is higher than the threshold on a particular host.
【单选题】
A scripted upgrade of ESXi fails due to an incorrect parameter in the upgrade script. What file must the administrator modify to correct the problem?___
A. vmreconfig.pl
B. hostinfo.pl
C. ks.cfg
D. boot.cfg
【单选题】
A VM folder contains VM1 and VM2. Group A has permission to power on virtual machines, defined on the VM folder and its children. Group B has permission to power off virtual machine VM2. If a user is a member of group A and B, what action can the user perform?___
A. Suspend VM2.
B. Power off VM1.
C. Power on and power off VM1.
D. Power on and power off VM2.
【单选题】
The networking team has requested to have a dedicated network for iSCSI traffic. This task has been assigned to the vSphere Administrator. What is the VMware-recommended way to accomplish this?___
A. Configure Static Routes on each ESXi Server.
B. Configure the right subnet.
C. Create a custom IP Stack.
D. Define a dedicated gateway for the iSCSI vmkernel.
【单选题】
To prevent possible failures or issues during a vSphere upgrade, which component should be upgraded first?___
A. ESXi Hosts
B. virtual machines
C. datastores
D. vCenter Server
【单选题】
What is the command for updating an ESXi host?___
A. esxcli software vib update –d /vmfs/volumes/Datastore/DirectoryName/PatchName.zip
B. esxupdate software update –d”/vmfs/volumes/Datastore/DirectoryName/PatchName.zip”
C. esxcli software update –d “/vmfs/volumes/Datastore/DirectoryName/PatchName.zip”
D. esxupdate software vib update –d /vmfs/volumes/Datastore/DirectoryName/PatchName.zip
【单选题】
A vSphere Administrator would like to identify which physical NUMA node their virtual machine is currently residing on. What esxtop metric would provide this information?___
A. GST_ND[x]
B. OVD_ND[x]
C. NRMEM
D. NHN
【单选题】
How can a vSphere administrator ensure that two virtual machines never run on the same datastore in a datastore cluster, while permitting the VMs to be load-balanced?___
A. Use an Intra-VM Anti-Affinity Rule.
B. Configure a storage DRS VM override.
C. Disable storage
D. RS for the VMs.
【单选题】
What is the VMware-recommended way to move a physical adapter out of Network I/O Control’s scope?___
A. Set the teaming policy to “Route Based on Physical NIC Load.”
B. Add the vmnic to the Net.NetNiocAllowOverCommit parameter in Advanced System Settings.
C. Add the vmnic to the Net.IOControlPnicOptOut parameter in Advanced System Settings.
D. Move the vmnic to a different vmUplink port on the Distributed Switch.
【单选题】
A VM folder contains VM1 and VM2. Group A has permission to power on virtual machines, defined on the VM folder and its children. Group B has permission to power off virtual machines, defined on the VM folder and its children. If a user is a member of Groups A and B, what will be the user’s effective permission on VM1 and VM2?___
A. Power on
B. Power off.
C. Power on and Power off.
D. Reset.
【单选题】
Group 1 is granted console interaction on a VM folder. User 1 is granted no console interaction on the same VM folder. What will be the outcome if User 1 tries to access the console of a virtual machine?___
A. User 1 will not be able to access the virtual machines in the VM folder.
B. User 1 will not have access to the virtual machine console.
C. User 1 will have access to the virtual machine console.
D. User 1 will have console access only via the vSphere Web Client.
【单选题】
Which statement is true regarding the use of VMFS3 datastores with vSphere 6.5?___
A. VMFS3 datastores can be used but not created.
B. VMFS3 datastores can be neither used nor created.
C. VMFS3 datastores will be present but unmounted.
D. VMFS3 datastores can be created and used.
【单选题】
In the Exhibit, each VM has a 1GHz non-expandable reservation. If all VMs are powered on in sequence, what would be the outcome?___
A. VM4 cannot be powered on.
B. VM5 cannot be powered on.
C. VM6 cannot be powered on.
D. VM3 cannot be powered on.
【单选题】
vSphere 6.5 introduced MAClearning capabilities for VMware’s virtual switches. What three benefits will it provide? (Choose three.)___
A. Reduced memory consumption.
B. Reduced consumption of extra CPU cycles.
C. Increased network throughput.
D. Prevent packet flooding inside the vSwitch.
【单选题】
What is the default pathing policy for most active-active arrays?___
A. Fixed
B. Most Recently Used
C. Dynamic
D. isk Morroring
【单选题】
Which command will show the iSCSI sessions on a ESXi 6.5 host?___
A. esxcli storage iscsi session get
B. esxcli iscsi session get
C. esxcli storage iscsi session
D. esxcli iscsi session list
【单选题】
Which of the following is not a parameter for traffic filtering or marking?___
A. virtual port ID
B. Protocol
C. Traffic Direction
D. DSCP value
E. Traffic redirection
【单选题】
A vSphere administrator wants to enable a virtual machine with Secure Boot, but in VM setting, Secure Boot option was not found under Boot Options. What could be the cause?___
A. The virtual hardware is not compatible.
B. The virtual machine has missing drivers.
C. The virtual machine OS does not support secure boot.
D. VMware Tools is not upgraded.
【单选题】
A virtual machine is connected on a distributed port group where the average bandwidth configured in the traffic shaping policy is 100 Mbps. The VM network adapter is configured with a reservation of 200 Mbps. What is the VM’s effective bandwidth?___
A. 200 Mbps
B. 100 Mbps
C. 150 Mbps
D. 400 Mbps
【多选题】
What are two reasons why a datastore in a Storage DRS cluster cannot enter maintenance mode?(Choose two.)___
A. Storage latency is too high to allow Storage DRS initiate Storage vMotion.
B. Storage DRS is configured for a VMFS3 datastore.
C. Storage
D. RS is disabled on the virtual disk.
【多选题】
What two methods are used to configure VMware vSphere Storage I/O Control shares and limits? (Choose two.)___
A. Assign shares and limits to VM virtual disks.
B. Assign shares and limits to datastores.
C. Assign shares and limits to Storage (DRS) clusters.
D. Assign shares and limits using VM storage policies.
【多选题】
ESXi 6.5 introduces VMFS6, which supports both 512e and 512n devices. What three configurations are supported when using these devices? (Choose three.) ___
A. Hosts with both 512e and 512n devices.
B. Storage vMotion between both 512e and 512n devices.
C. Datastore Extents spanned between both 512e and 512n devices.
D. Storage DRS clusters containing only both 512e and 512n devices.
【多选题】
A vSphere Administrator observes that the Primary VM configured with Fault Tolerance is executing slowly. After further investigation, it is determined that the Secondary VM is on an overcommitted ESXi host. What two methods will correct the problem? (Choose two.)___
A. Use Storage vMotion to migrate the Secondary VM to another datastore.
B. Use vMotion to migrate the Secondary VM to a different ESXi host.
C. Configure a CPU limit on the Primary VM which will also apply to the Secondary VM.
D. Turn off and turn on FT in order to recreate the Secondary VM on a different datastore.
【多选题】
Which two features require the use of Host Profiles? (Choose two.)___
A. Host Customizations
B. shared storage
C. Auto
D. eploy
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
Which two statements correctly describe VM-Host affinity rules? (Choose two.) ___
A. When there is more than one VM-Host affinity rule in a vSphere DRS cluster, the rules are applied equally.
B. After creating a VM-Host affinity rule, its ability to function in relation to other rules is predetermined.
C. When there is more than one VM-Host affinity rule in a vSphere
D. RS cluster, the rules will be ranked.
【多选题】
An administrator wants to enable proactive HA by moving virtual machines automatically if a hardware alert is triggered. What are the three required settings? (Choose three.)___
A. Set vSphere DRS Automation to Partially Automated.
B. Turn on Proactive HA.
C. Set the Proactive HA Automation Level to Manual.
D. Set the Proactive HA Automation Level to Automated.
E. Turn on vSphere HA and vSphere DRS.