【单选题】
室外架空交流电源防雷保安器，冲击通流容量不小于20kA，限制电压应不大于_______。[331010101]___
A. 380V
B. 500V
C. 1000V
D. 1500V
查看试卷，进入试卷练习
微信扫一扫，开始刷题
相关试题
【单选题】
电源防雷箱的的功率应不大于被保护设备总用电量的_______。[331010103]___
A. 1.2倍
B. 2倍
C. 2.2倍
D. 2.5倍
【单选题】
室内数据传输线长度在_______时，可在一端设备接口处设置防雷保安器。[332030203]___
A. 30m～50m
B. 50m～80m
C. 50m～100m
D. 60m～120m
【单选题】
室内数据传输线长度大于_______时，宜在两端设备接口处设置防雷保安器。[322030203]___
A. 50m
B. 80m
C. 100m
D. 120m
【单选题】
采集驱动信号传输线选用冲击通流量1.5kA，限制电压不大于_______的防雷保安器。[331010102]___
A. 60V
B. 80V
C. 110V
D. 220V
【单选题】
视频信号传输线选用冲击通流量1.5kA，限制电压不大于_______的防雷保安器。[331010101]___
A. 10V
B. 30V
C. 50V
D. 60V
【单选题】
交流轨道电路选用防雷保安器：工作电压小于36V时，限制电压应小于或等于_______。[331010101]___
A. 60V
B. 110V
C. 190V
D. 220V
【单选题】
交流轨道电路选用防雷保安器：工作电压36V～60V时，限制电压应小于或等于_______。[331010101]___
A. 220V
B. 330V
C. 350V
D. 380V
【单选题】
交流轨道电路选用防雷保安器：工作电压60V～110V时，限制电压应小于或等于_______。[331010101]___
A. 380V
B. 500V
C. 700V
D. 1000V
【单选题】
交流轨道电路选用防雷保安器：工作电压110V～220V时，限制电压应小于或等于_______。[331010101]___
A. 380V
B. 500V
C. 700V
D. 1000V
【单选题】
直流轨道电路选用防雷保安器：工作电压小于24V时，限制电压应小于或等于_______。[331010102]___
A. 60V
B. 75V
C. 110V
D. 220V
【单选题】
贯通地线在信号机房建筑物一侧每隔2m～3m用裸铜线与环形接地装置连接，两端各连接_______。[311030203]___
【单选题】
无线天线避雷针的接地装置应单独设置，并距环形接地装置_______以上。[311010103]___
A. 15m
B. 20m
C. 25m
D. 30m
【单选题】
无线天线避雷针的接地装置应单独设置，特殊情况下距环形接地装置不应小于_______。[311010103]___
A. 5m
B. 8m
C. 10m
D. 15m
【单选题】
ZPW-2000A无绝缘移频自动闭塞系统补偿电容采用_______进行现场设置。[312030201]___
A. △法
B. 每100m装一个
C. 等差法
D. 等间距法
【单选题】
ZC-8接地电阻测量仪在使用时，两接地棒即电位探针P＇和电流探针C＇沿直线相距_______。[322010103]___
A. 15m
B. 20m
C. 25m
D. 30m
【单选题】
S700K型电动转辙机因故不能转换到底时，电流一般不大于_______。[313010102]___
【单选题】
S700K电动转辙机的单线圈电阻不大于_______。[323010103]___
A. 50Ω
B. 54Ω
C. 58Ω
D. 64Ω
【单选题】
S700K电动转辙机代号A15/A16的输出额定转换力为_______。[311010103]___
A. 2500N
B. 3000N
C. 4500N
D. 6000N
【单选题】
S700K电动转辙机代号A17/A18的输出额定转换力为_______。[311010103]___
A. 2500N
B. 3000N
C. 4500N
D. 6000N
【单选题】
S700K电动转辙机代号A33/A34的输出额定转换力为_______。[311010103]___
A. 2500N
B. 3000N
C. 4500N
D. 6000N
【单选题】
JM-A型密贴检查器表示杆动程为_______。[311010103]___
A. 30mm～97mm
B. 65mm～120mm
C. 65mm～140mm
D. 90mm～150mm
【单选题】
JM-A型密贴检查器挤岔断表示的动程：从启动片的滚轮接触表示杆斜面开始为_______。[311010103]___
A. 10mm～13mm
B. 15mm～18mm
C. 15mm～20mm
D. 19mm～25mm
【单选题】
下列关于JM-A型密贴检查器说法正确的是：_______。[331010103]___
A. 每台密贴检查器应设有一组表示接点和一组斥离接点
B. 每台密贴检查器应设有一组表示接点和两组斥离接点
C. 每台密贴检查器应设有两组表示接点和一组斥离接点
D. 每台密贴检查器应设有两组表示接点和两组斥离接点
【单选题】
设在道岔两侧的JM-A型密贴检查器，一台密贴检查器的表示杆及其接点组检查尖轨的密贴位置，另一台密贴检查器的表示杆及其接点组检查尖轨的斥离_______以上位置。[331010204]___
A. 60mm
B. 65mm
C. 75mm
D. 78mm
【单选题】
JM-A型密贴检查器动接点环打入静接点片的深度应不小于_______。[332010204]___
A. 3mm
B. 4mm
C. 5mm
D. 6mm
【单选题】
JM-A型密贴检查器滚轮在表示杆缺口中平面或上平面滚动时，启动片离开表示杆的平面应为_______。[331010204]___
A. 0.3mm～0.8mm
B. 0.5mm～1.7mm
C. 0.3mm～2mm
D. 1mm～3mm
【单选题】
下列关于JM-B型密贴检查器说法正确的是：_______。[331010204]]___
A. 每台密贴检查器应设有一组表示接点和一组斥离接点
B. 每台密贴检查器应设有一组表示接点和两组斥离接点
C. 每台密贴检查器应设有两组表示接点和一组斥离接点
D. 每台密贴检查器应设有两组表示接点和两组斥离接点
【单选题】
JM-B型密贴检查器挤岔断表示的动程：从开关轴接触表示杆斜面开始小于或等于_______。[331010204]___
A. 3mm
B. 4mm
C. 5mm
D. 6mm
【单选题】
ELP-319型密贴检查器检测杆与接点座配合工作可检测_______尖轨动程。[331010204]___
A. 90mm～130mm
B. 170mm～190mm
C. 30mm～190mm
D. 50mm～100mm
【单选题】
S700K电动转辙机单芯电缆控制距离可达_______。[331010204]___
A. 1.5km
B. 2.0km
C. 2.5km
D. 3.0km
【单选题】
S700K型电动转辙机上下两检测杆无张嘴和左右偏移现象，检测杆头部的叉形连接头销孔的磨损旷量不大于_______。[312010204]___
A. 0.5mm
B. 1mm
C. 1.5mm
D. 2mm
【单选题】
三相电动机电源线中，任意两根线对调会使电动机_______。[32301024]___
A. 转速变慢
B. 转速变快
C. 不转
D. 反转
【单选题】
ZPW-2000A无绝缘移频自动闭塞系统_______用于实现主轨道电路、小轨道电路的调整。[311010103]___
A. 发送检测器
B. 侧线检测盘
C. 衰耗盘
D. 接收器
【单选题】
ZPW-2000R型无绝缘轨道电路在最不利条件下，用0.15Ω标准分路线分路，主轨道无分路死区段。调谐区分路死区段不大于_______。[331010103]___
【单选题】
ZP·WD型18信息移频轨道电路,在机车入口端轨面,用_______标准分路电阻线分路时,应满足动作机车信号的最小短路电流的要求。[311010103]___
A. 0.03Ω
B. 0.04Ω
C. 0.05Ω
D. 0.06Ω
【单选题】
ZP·WD型18信息移频轨道电路,在调整状态下,受电端接收盒限入电压应不小于_______,轨道电路应可靠工作。[322010101]___
A. 240mV
B. 250mV
C. 280mV
D. 290mV
【单选题】
连接两个节点的一段电路称为_______。[222000000]___
【单选题】
S700K型电动转辙机表示电路中电阻R1的阻值是_______。[312010103]___
A. 300Ω
B. 500Ω
C. 800Ω
D. 1000Ω
【单选题】
S700K型电动转辙机表示电路整流堆部分串入电阻R2的阻值是_______。[312010103]___
A. 300Ω
B. 500Ω
C. 800Ω
D. 1000Ω
【单选题】
信号微机监测系统不能监督与_______结合部有关状态。[311010105]___
推荐试题
【单选题】
How can you protect CDP from reconnaissance attacks？___
A. Enable dynamic ARP inspection on all untrusted ports.
B. Enable dot1x on all ports that are connected to other switches.
C.
D. isable CDP on ports connected to endpoints.
【单选题】
Which type of attack can exploit design flaws in the implementation of an application without ？___
A. DHCP starvation attacks
B. low-rate dos attacks
C. application DDos flood attacks
D. application DDoS flood attacks
E. volume-based DDoS attacks
【单选题】
Which option is a key security compone nt of and MDM deployment ？___
A. using network-specific installer packages
B. using an application tunnel by default
C. using self-signed certificates to validate the server
D. using MS-CHAPv2 as the primary
E. AP method
【单选题】
Which Firepower Management Center feature detects and block exploits and hack attempts？___
A. Content blocker
B. file control
C. intrusion prevention
D. advanced malware protection
【单选题】
hich description of the nonsecret numbers that are used to start a Diffie- Hellman exchange is ture？___
A. They are preconfigured prime integers.
B. They are large pseudorandom numbers.
C. They are very small numbers chosen from a table of known valuses
D. They are numeric values extracted from ha shed system hostnames
【多选题】
Which two characteristics of an application layer firewall are true？___
A. provides stateful firewal functionality
B. has low processor usage
C. provides protection for multiple applications
D. provides rever se proxy services
E. is immune to URL manipulation
【多选题】
Which two devices are components of the BYOD architectural framework？___
A. Nexus 7010 switch
B. Cisco 3945 Router
C. Identify Services Engine
D. Wireless Access oints
E. Prime Infrastructure
【多选题】
Which two actions can a zone based firewall take when looking at traffic？ ___
A. forward
B. inspect
C. drop
D. broadcast
E. filter
【多选题】
n which two situations should you use in-band management？___
A. when management applications need concurrent access to the device
B. when you require administrator access from multiple locations
C. when a network device fails to forward packets
D. when you require ROMMON access
E. when the control plane fails to respond
【多选题】
What are two ways to prevent eavesdropping when you perform device management tasks？___
A. Use an SSH connection.
B. Use SNMPv3
C. Use out-of-band management
D. Use SNMP
E. Use in-band management
【多选题】
Which two features are commonly used CoPP and CPPr to protect the control plane？ ___
A. QoS
B. traffic classification
C. access lists
D. policy maps
E. class maps
F. Cisco Express Forwarding
【多选题】
Which four tunne ling prot ocols are enabled in the Dfit GrpPolicy group policy ？___
A. Clientless SSL VPN
B. SSL VPN Client
C. PPTP
D. L2TP/IPsec
E. IPsec IKEv1
F. IPsec IKEv2
【多选题】
Which two statements regarding the aSA VPN configurations are correct？___
A. The asa has a certificate issued by an external certificate authority associated to the ASDM TrustPoint1
B. The Default WEBVPNGroup Connection Profile is using the aaa with RADIUS server method
C. The Inside-srvbook mark references the https://192.168.1.2url
D. Only Clientless SSL VPN access is allowed with the Sales group policy
E. Any Connect， IPSec IKEv1， and IPSec IKEv2 VPN access is enabled on the outside interface
F. The Inside -SRV bookmark has not been applied to the Sales group policy
【多选题】
Which three ESP fields can be encrypted during transmission？___
A. Security Parameter Index
B. Sequence Number
C. MAC Address
D. Padding
E. Pad length
F. Next Header
【多选题】
.Which three statements de scribe DHCP spoofing attacks？___
A. They can modify traffic in transit.
B. They are used to perform man- in-the-middle attacks
C. They use ARP poisoning
D. They can access most network devices
E. They protect the ide ntity of the attacker by masking the DHCP address.
F. They are can physically modify the network gateway.
【多选题】
Which statement about the communication between interfaces on the same security level is true？___
A. Interfaces on the same security level require additional configuration to permit interinterface communication
B. Configuring interfaces on the same security level can cause asymmetric routing
C. All traffic is allowed by default between interfaces on the same security level
D. You can configure only one interface on a n individual security level
【多选题】
In which two situations should you use in band management？ ___
A. when the control plane fails to respond
B. when you require administrator access from multiple locations
C. when you require ROMMON access.
D. where a network device fails to forward packets
E. when multiple ma nagement applications need concument access to the device.
【多选题】
Which two features are supported in a VRF-aware softwar infrastructure before VRF-lite?___
A. multicast
B. fair queuing
C. WCCP
D.
E. IGRP
【多选题】
.Which loS command do you enter to test authentication again a AAA server？___
A. dialer aaa suffix <suffix> password <password>
B. ppp authentication chap pap test
C. test aaa-server authentication dialer group user name <user> password <password>
D. aaa authentication enable default test group tacases
【多选题】
Which two statements about the self zone on a cisco Xone based policy firewall are true？___
A. Multiple interfaces can be assigned to the self zone
B. it supports stateful inspections for multicast traffic
C. zone pairs that include the self zone apply to traffic transiting the device.
D. it can be either the source zone or the destination zone
E. traffic entering the self zone must match a rule
【多选题】
Which type of attack can exploit design flaws in the implementation of an application without ？___
A. DHCP starvation attacks
B. low-rate dos attacks
C. application DDos flood attacks
D. application DDoS flood attacks
E. volume-based DDoS attacks
【单选题】
Which type of firewall can server as the interme diary between a client and a server ?___
A. Stateless firewall
B. application firewall
C. proxy firewall
D. personal firewall
【单选题】
What is the highest security level that can be configured for an interface on an ASA？___
【单选题】
Which term refers to the electromagnetic interference that can radiate from network cables？___
A. Gaussian distributions
B. Doppler waves
C. emanations
D. multimode distortion
【单选题】
How does a zone pair handle traffic if the policy de fination of the zone pair is missing?___
A. It inspects all traffic.
B. It drops all traffic.
C. It permits all traffic wihtout logging
D. It permits and logs all traffic
【单选题】
default how does a zone based firewall handle traffic to add from the self zone？___
A. It permits all traffic without inspection
B. It inspects all traffic to determine how it is handled
C. It permits all traffic after inspection
D. It frops all traffic
【单选题】
Which command should beused to ena ble AAA Authentication to determine if a user can access the privilege command level？___
A. aaa authentication enable local
B. aaa authentication enable level=
C. aaa authentication enable method de fault
D. aaa authentication enable defa ult local
【单选题】
On an ASA， the policy indicates that traffic should not be translated is often referred to as which of the following？___
A. NAT zero
B. NAT forward
C. NAT nul
D. NAT allow
【单选题】
Which protocol offers data Integrity encryption， authentication， and anti-replay functions for IPSec VPN？___
A. ESP protocol
B. IKEv3 Protocol
C. AH protoco
D. IKEv1 Protocol
【单选题】
Which component offers a variety of security Solution， including firwall， IF Antivirus and antiphishing features？___
A. Cisco loS router
B. Cisco ASA 5500 Ser ies security appliance
C. Cisco ASA 5500 X series Next Gen Security appliance
D. Cisco 4200 series IPS appliance
【单选题】
Refer to the exhibit， A Network Secur ity administrator check the ASa firewall NAT policy table rith show nat command， which statement is fails？___
A. There are only reverse translation matches for the REAL SERvER object
B. First policy in the Section 1 is a dynamic nat entry defined in the object configuration
C. NAT policy in section 2 is static entry de fined in the object configuration
D. Translation in Section 3 used when a connection does not matches any entries in first two sections
【单选题】
What is true of an aSa in transparent mode ?___
A. It supports OSPF
B. It requires an IP address for each interface
C. It requires a management IP address
D. It allows the use of dynamic NaT
【单选题】
What is the effect of the ip scp server enable command？___
A. It references an access list that allows specific SCP servers
B. It allows the router to initiate requests to an SCP server
C. It allows the router to become an SCP server
D. It adds SCP to the list of allowed copy functions
【单选题】
How can you mitigate attacks in which the attacker attaches more than one vLan tag to a packet？___
A. Assign an access VLAN to every active port on the switch
B. Disable Ether Channel on the switch
C. Explicitly identity each VLAN allowed across the trunk
D.
E. nable transparent VTP on the switch
【单选题】
Which technology can you implement to centrally mitigate potential threats when users on your network download files that might be malicious？___
A. Enable file-reputation services to inspect all files that traverse the company network and block files with low reputation scores
B. Verify that the compa ny IpS blocks all known malicious website
C. Verity that antivirus software is installed and up to date for all users on your network
D. Implement URL filtering on the perimeter firewall
【单选题】
What is the most common implementation of PaT in a standard networked environment？___
A. configuring multiple external hosts to join the self zo ne and to communicate with one another
B. configuring multiple internal hosts to communicate outside of the network using the outside interface IP address
C. configuring multiple internal hosts to communicate outside of the network by using the inside interface IP address
D. configuring an any any rule to enable external hosts to communicate inside the network
【单选题】
Which component of a bYod architecture provides aAa services for endpoint access ?___
A. Integrated Services Router
B. access point
C. ASA
D. Identity Services
E. ngine
【单选题】
You are configuring a NAT rule on a Cisco ASA ,Which description of a mapped interface is true?___
A. It is mandatory for all firewall modes
B. It is optional in routed mode
C. It is optional in transparent mode
D. It is mandatory for ide ntity NAT only
【单选题】
Which description of the use of a private key is true ？___
A. The sender signs a message using the receivers private key
B. The sender signs a message using their private key
C. The sender encrypts a message using the receivers private key
D. The receiver decrypts a n15ssage using the sender's private key
【单选题】
Which mechanism does the FireAMP Connector use to avoid conflicts with other security applications such as antivirus products ?___
A. Virtualization
B. Containers
C. Sandboxing
D.
E. xclusions
