刷题
导入试题
【单选题】
外部直流电源接入飞机电网是受什么部件控制?___
A. GPCU
B. GCU
C. GAPCU
D.
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
C
解析
暂无解析
相关试题
【单选题】
当TR1失效后,DCESSBUS可从什么地方得到电源?___
A. ACESSBUS
B. DCBATBUS
C. CSM/G
D.
【单选题】
当TR2失效后,DCESSBUS由什么部件提供电源?___
A. TR1
B. ESSTR
C. BAT2
D.
【单选题】
当飞机未通电(交/直流均无)时,在什么地方可检查电瓶电压?___
A. 无指示
B. 在电瓶舱内的电压表
C. 可直接在电源面板上的指示窗查看
D.
【单选题】
电瓶接触器受什么部件控制?___
A. 发电机控制组件(GCU)
B. 电瓶充电限制器(BCL)
C. 静变流机
D.
【单选题】
在正常供电构型下,DCESSBUS如何得到电源?___
A. 来自TR1(DCBUS1)
B. 来自ESSTR
C. 来自TR2(DCBUS2)
D. 来自电瓶2
【单选题】
GALLEYFAULT灯亮的含义是___
A. 后厨房设备被卸载
B. 所有厨房设备被卸载
C. 当任一发电机(IDG或APU)过载
D.
【单选题】
当APU发电机在地面发生过载故障后,下列说法正确的是()___
A. 所有商用的子汇流条被卸载
B. 所有厨房的汇流条被卸载
C. 所有厨房设备依然有电
D.
【单选题】
增强型电源系统属于哪类系统?___
A. Ⅰ
B. Ⅱ
C. Ⅲ
D.
【单选题】
增强型电源系统是如何同MCDU相连?___
A. 直接通过每一个GCU
B. 通过GAPCU和CFDIU
C. 通过CFDIU同EGIU(ELECTRICALGENERATIONINTERFACEUNIT)
D.
【单选题】
正常构形下,DCBUS1由谁供电?___
A. 来自变压整流器1
B. 来自主变压整流器
C. 来自变压整流器2
D. 来自电瓶2
【单选题】
ACESSBUS的正常电源来自:___
A. 交流汇流条1
B. 交流汇流条2
C. 应急发电机
D. 静变流机
【单选题】
直流电瓶汇流条如何供电:___
A. 直流汇流条1或电瓶
B. 直流汇流条1,直流汇流条2或电瓶
C. 直流汇流条2或电瓶
D. 不确定
【单选题】
当电源控制面板上GEN1按钮在关位时会出现什么情况?___
A. 1号和2号交流汇流条没有电并且应急发电机自动连接
B. 1号交流汇流条因1号发电机不起作用而由2号发电机供电
C. 1号交流汇流条因1号发电机网路继电器在断开位而由2号发电机供电
D. 1号交流汇流条没有电因为1号GEN1继电器在断开位并且转换接触器没有闭合
【单选题】
如果ACBUS1故障,ACESSBUS由谁供电:___
A. 应急发电机
B. 交流汇流条2
C. 静变流机
D. 不确定
【单选题】
哪一个电源向ESSTR供电?___
A. ACBUS1或ACBUS2
B. ACBUS1和ACBUS2
C. ACESSBUS或应急发电机
D. 不确定
【单选题】
当电源控制面板上GEN1和GEN2开关在“关”(OFF)位时:___
A. 发电机中断供电且GLC开路
B. 发电机继续供电且GLC开路
C. 发电机不发电且GLC开路
D. 不确定
【单选题】
交流电转换使交流汇流条:___
A. 并联供电
B. 由任一发电机或外部电源供电
C. 只由APU发电机或外部电源供电
D. 不确定
【单选题】
哪一个组件控制电瓶接触器的通断?___
A. GCU
B. BCL
C. 静变流机
D. 电源面板上的BAT按钮
【单选题】
当TR2失效时,可否通过客舱顶板上的MAINTBUS开关直接给勤务汇流条供电?___
A. 可以
B. 不能
C.
D.
【单选题】
如何对变压整流器进行复位?___
A. 通过BCL或在电子舱内的一个按钮
B. 通过在电子舱内的一个按钮或电源接通时自动复位
C. 通过CFDS或在电子舱内的一个按钮
D. 不确定
【单选题】
何时过度放电保护功能断开电瓶接触器?___
A. 在空中当电瓶电压低于23V持续15秒
B. 在地面当电瓶电压低于23V持续15秒
C. 任何时候当电瓶电压低于23V持续15秒
D. 不确定
【单选题】
在空中应急电源构型下,APU启动程序何时被禁止?___
A. 在刚进入构型的45秒期间或到应急发电机供电时
B. 当应急发电机供电时
C. 应急发电机刚开始供电的45秒内
D. 不禁止
【单选题】
何时电源控制面板上的GALY&CAB按钮上的故障灯亮?___
A. 当厨房用电设备有故障时
B. 当客舱用电设备有故障时
C. 当1部IDG过载时
D. 当厨房用电设备负载过大而被卸载时
【单选题】
何时电源控制面板上的IDG按钮上的故障灯亮?___
A. 当滑油温度过高或滑油压力过低时
B. 当滑油温度过高且滑油压力过低时
C. 当CSD机构有故障时
D. 当CSD机构脱开后
【单选题】
何时TR2最小电流保护功能被禁止?___
A. 在地面飞机电网由APU发电机供电时
B. 在地面当外接电源只给勤务汇流条供电时
C. 在地面当外接电源给勤务汇流条供电时
D. 不确定
【单选题】
若IDG热熔断开,则___
A. IDG必须更换
B. IDG在地面进行复位后可继续工作
C. IDG在地面进行复位和按MM进行维护后可继续工作
D. 不确定
【单选题】
IDG上的冷却旁通valve何时打开?___
A. 在滑油温度低时
B. 在滑油温度高时
C. 在油滤堵塞时
D. 不确定
【单选题】
断开IDG,按钮应被按下:___
A. 不超过3秒
B. 不超过5秒
C. 超过3秒
D. 直至故障灯熄灭
【单选题】
在应急电源板上,如果在“RATANDEMERGEN”(冲压空气涡轮和应急发电机)标签下的故障灯亮:___
A. 冲压空气涡轮没有放出
B. 当ACBUS1和2无电(大于100KT)或DCBATBUS无电时,应急发电机不再供电
C. 应急发电机在供电,但交流主汇流条没有电
D. 当ACBUS1和2无电且空速大于100节时,应急发电机未供电
【单选题】
在应急电源构形下,ACESSBUS:___
A. 在空速大于100节时自动卸载
B. 在空速小于100节时自动卸载
C. 在空速小于50节时自动卸载
D. 在空速大于50节时自动卸载
【单选题】
电瓶何时为DCBATBUS供电:___
A. APU开车时
B. ACBUS1无电时
C. ACBUS1和2无电时(小于100节)
D. A和C
【单选题】
当你想检查电瓶电压时,你必须将电瓶按钮设在:___
A. 自动位
B. OFF位
C.
D.
【单选题】
电源控制面板上电瓶按钮的故障灯何时燃亮:___
A. 电瓶电压小于25伏
B. 在空中,电瓶按钮设在关位
C. 充电电流以反常速率增加
D. 不确定
【单选题】
在某些情况下,静变流机可能由谁供电:___
A. 热汇流条1和热汇流条2
B. 热汇流条1
C. 直流电瓶汇流条
D. 不确定
【单选题】
RAT的释放是如何控制的?___
A. 两个电磁valve同时有电时放出
B. 两个电磁valve中的任何一个有电时放出
C. 只有一个电磁valve在控制
D. 不确定
【单选题】
RAT的电磁valve是如何供电的?___
A. 由电瓶或热电瓶汇流条供电
B. 由DCBATBUS供电
C. 由DCBUS1或2供电
D. 不确定
【单选题】
当应急发电机的GCU探测到一个内部故障时:___
A. 控制液压的电磁valve关断,GLC断开
B. 发电机低速运转,GLC断开
C. 控制液压的电磁valve关断,励磁场关断,GLC不断开
D. 不确定
【单选题】
静变流机故障信号送至哪部计算机?___
A. GAPCU
B. GCU
C. BCL
D. GPCU
【单选题】
飞机上电网工作正常,若在电源控制面板上将ACESSFEED按钮弹出放ALTN位,则:___
A. ACESSBUS由应急发电机供电
B. ACESSBUS由ACBUS1供电
C. ACESSBUS由ACBUS2供电
D. 不确定
【单选题】
在何种构型下加油电源10分钟后自动切断?___
A. 由勤务汇流条供电时
B. 由热汇流条供电时
C. 上述两项都对
D. 不确定
推荐试题
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
【单选题】
An administrator is installing Windows into a virtual machine. The DVD has been mounted on the Host and configured for the virtual machine as shown in the Exhibit. Based on the exhibit, when the virtual machine is booted, why would it attempt to search for a PXE server? ___
A. The CD/DVD device is not connected.
B. The ISO is in the incorrect storage location.
C. The OS minimum requirements have not been met.
D. The CD/DVD device is not set to Client Device.
【单选题】
What component must be installed prior to deploying a vCenter Server in vSphere 6.x? ___
A. vCenter Identity Services
B. Platform Services Controller
C. vCenter Single Sign-On
D. Client Integration Plug-In
【单选题】
What is a valid plug-in status for a plug-in that has been added to a vSphere client? ___
A. Disabled
B. Unknown
C. Stopped
D. Installed
【单选题】
Users of an application are reporting performance issues. The following performance values are observed in the vSphere Web Client: <Host CPU utilization is 90%> <Virtual Machine memory utilization is consistently greater than 90% CPU Ready values are higher than 20%> What could be the cause of the application performance issue? ___
A. The host is lacking the CPU resources required to meet the demand.
B. The host is lacking the memory resources required to meet the demand.
C. The virtual machine is lacking the CPU resources required to meet the demand.
D. The virtual machine is lacking the memory resources required to meet the demand.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is re-provisioning an ESXi host and moving it to another datacenter. Which DCUI option should the administrator use to revert the system configuration to the default settings? ___
A. Reset System Configuration
B. Rebuild Default System Configuration
C. Revert System Configuration
D. Renew Default System Configuration
【单选题】
An administrator has just completed installing an ESXi 6.x host, but doesn't know what address has been configured. Where is the ESXi host IP address configured? ___
A. RVC console
B. Direct Console User Interface
C. vSphere Web Client
D. vSphere Client
【单选题】
When is it possible to place a VMFS5 datastore in maintenance mode? ___
A. When it is a member of a Storage DRS cluster
B. When it is a member of Virtual SAN cluster
C. When it is a member of a multi-extent datastore
D. When it is a member of a Virtual Volume
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Which Single Sign-On deployment mode should an administrator use for two 6.x vCenter Servers configured with linked mode? ___
A. Basic Single Sign-On with vCenter Server Heartbeat
B. Multisite Single Sign-On
C. Basic Single Sign-On
D. Single Sign-On with Linked Mode
【单选题】
What is required when changing a virtual machine name using the vSphere Web Client? ___
A. Verify connectivity to the ESXi host where the virtual machine is running and its inventory list is accessible.
B. Verify in which datastore the virtual machine resides and that you have access and its inventory list is accessible.
C. Verify that virtual machine files are stored in the same datastore and can be accessed in the datastore browser list.
D. Verify the virtual machine is not running in Fault Tolerant mode and that it is not in a Distributed Resource Scheduler cluster.
【单选题】
An administrator deploys vRealize Operations into a vSphere 6.x environment. After the deployment, the administrator notices that badges are not appearing. What is a likely cause of this behavior? ___
A. Badges do not appear until you register vRealize Operations with vCenter Server.
B. Badges do not appear until you register a vCenter Server in vRealize Operations.
C. The vRealize Operations appliance needs to be redeployed.
D. The vCenter Server appliance needs to be redeployed.
【单选题】
How are ports scaled on vSphere Standard Switches (vSS)? ___
A. Ports on a vSS can be dynamically scaled up and down.
B. Ports on a vSS can only be statically scaled up or down.
C. Ports on a vSS can only be dynamically scaled down.
D. Ports on a vSS can only be dynamically scaled up.
【单选题】
A High Availability (HA) cluster is configured to respond to a given number of host failures. The cluster contains virtual machines configured with these settings: VM1 has a 1GHz CPU reservation and no Memory reservation VM2 has a 2GHz CPU reservation and no Memory reservation VM3 has no CPU reservation and no Memory reservation . Given this information, what is the correct slot size for the cluster? ___
A. The CPU Reservation should be set to 32MHz and the memory reservation should be set to 32MB plus memory overhead.
B. The CPU reservation should be set to 1 GHz and the memory reservation should be set to 0MB plus memory overhead.
C. The CPU reservation should be set to 2 GHz, and the memory reservation should be set to 0MB plus the virtual machine memory overhead.
D. The CPU reservation should be set to 2 GHz, and the memory reservation should be set to 32MB, plus the virtual machine memory overhead.
【单选题】
An administrator is planning a vSphere infrastructure with the following specific networking requirements: <The ability to shape inbound (RX) traffic> <Support for Private VLANs (PVLANs)> <Support for LLDP (Link Layer Discovery Protocol)>. What is the minimum vSphere Edition that will support these requirements? ___
A. vSphere Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
【单选题】
When you add an ESXi 6.x host to a new Cluster, which vSphere object owns the CPU and Memory resources of the hosts? ___
A. vCenter Server
B. Datacenter
C. Cluster
D. Host
【单选题】
A user is trying to retrieve objects from a SharePoint server and finds the request is taking an excessive amount of time. An administrator tries to isolate the issue and notes the following: Application performance is poor when compared to virtual machines on other hosts. Performance improves when the virtual machine is moved to another host. The virtual machine encounters higher than expected CPU %Ready times. What conclusion can be reached regarding the performance issues for this virtual machine? ___
A. Host Power Management is directly impacting virtual machine performance.
B. The virtual machine has a large number of snapshots.
C. The Path Selection Policy for the storage device is set differently on the affected host.
D. Network I/O control is configured for the portgroup.
【单选题】
A virtual machine template is accidently removed from the vCenter Server Inventory. Which method would be used to recover the template back into the environment?___
A. Use the datastore browser to locate the template, then right click and add the .vmtx file to inventory.
B. Use the datastore browser to locate the template, then right click and add the .vmx file to inventory.
C. Using the Managed Object Browser and adding the template from the ManagedObjectReference:GuestFileManager object.
D. Using the Managed Object Browser and adding the template from the ManagedObjectReference:VirtualDiskManager object.
【单选题】
A vSphere administrator needs to backup a virtual machine that has a Microsoft SQL Server Database installed. Which solution allows for an application quiesce to occur during backup?___
A. VMware vCenter Converter
B. VMware vCenter Site Recovery Manager
C. VMware vSphere Replication
D. VMware vSphere Data Protection Advanced
【单选题】
An administrator is migrating a virtual machine from a Test cluster to a Production cluster. The two environments do not have any shared storage. What is the easiest way to accomplish this task? ___
A. Perform a Storage vMotion.
B. Perform a regular vMotion.
C. Perform a Virtual to Virtual migration.
D. Perform a backup and restore using VMware Data Protection.
【单选题】
An administrator must determine an appropriate backup solution, given these conditions: 50 of the virtual machines are in a resource pool named Finance. 50 of the virtual machines are in a resource pool named QA. Which solution allows an administrator the ability to backup 100 virtual machines? ___
A. Use Snapshot Manager on the vCenter Server to backup the virtual machines.
B. Use the VMware Consolidated Backup (vcb) tool on the ESXi Host to backup the virtual machines.
C. Use the VMware Data Recovery (VDR) Appliance on the vCenter Server to backup the virtual machines.
D. Use the VMware Data Protection (VDP) Appliance on one of the
E. SXi Hosts to backup the virtual machines.
【单选题】
What is a benefit of using Enhanced vMotion Compatibility for an environment? ___
A. EVC masks CPU features to allow compatibility between hosts that are dissimilar.
B. EVC allows for cross platform vMotion to occur.
C. EVC enables Long
D. istance vMotion.
【单选题】
How many Link Aggregation Groups (LAGs) can be configured on a vSphere 6.x Distributed Switch? ___
A. 64
B. 96
C. 128
D. 256
【单选题】
How many Link Aggregation Groups (LAGs) can be configured on a vSphere 6.x Distributed Switch? ___
A. 64
B. 96
C. 128
D. 256
欢迎使用我爱刷题
×
微信搜索我爱刷题小程序
温馨提示
×
请在电脑上登陆“www.woaishuati.com”使用