相关试题
【单选题】
16图中D1-D3为理想二极管,A,B,C灯都相同,试问___灯最亮。
【单选题】
18在单相桥式整流电容滤波电路中,设U2为其输入电压,输出电压的平均值约为___。
A. U0=0.45U2
B. U0=1.2U2
C. U0=0.9U2
D. U0=1.4U2
【单选题】
19在单相桥式整流电路中,设U2为其输入电压,输出电压的平均值约为___。
A. U0=0.45U2
B. U0=1.2U2
C. U0=0.9U2
D. U0=1.4U2
【单选题】
20在半波整流电容滤波电路中,设U2为其输入电压,输出电压的平均值约为___。
A. U0=0.45U2
B. U0=1.2U2
C. U0=0.9U2
D. U0=1.4U2
【单选题】
21在半波整流电路中,设U2为其输入电压,输出电压的平均值约为___。
A. U0=0.45U2
B. U0=1.2U2
C. U0=0.9U2
D. U0=1.4U2
【单选题】
22温度影响了放大电路中的___,从而使静态工作点不稳定。
A. 电阻;
B. 电容;
C. 三极管;
D. 电源。
【单选题】
23用直流电压表测得放大电路中某三极管各极电位分别是2V、6V、2.7V,则三个电极分别是___。
A. [B、C、E]
B. [C、B、E]
C. [E、C、B]
【单选题】
24共射极放大电路的交流输出波形上半周失真时为___
【单选题】
25三极管的反向电流ICBO是由___组成的。
A. 多数载流子
B. 少数载流子
C. 多数载流子和少数载流子
【单选题】
27如果在NPN型三极管放大电路中测得发射结为正向偏置,集电结也为正向偏置,则此管的工作状态为___
A. 放大状态;
B. 截止状态;
C. 饱和状态;
D. 不能确定。
【单选题】
28在以下三种电路中输入电阻最大的电路是___。
A. 共基放大电路
B. 共集放大电路
C. 共射放大电路
【单选题】
29在以下三种电路中既能放大电流,又能放大电压的电路是___。
A. 共基放大电路
B. 共集放大电路
C. 共射放大电路
【单选题】
30在以下三种电路中输出电阻最小的电路是___;
A. 共基放大电路
B. 共集放大电路
C. 共射放大电路
【单选题】
当PNP型晶体管工作在放大区时,各极电位关系为uC ___uB。
【单选题】
32当PNP型晶体管工作在放大区时,各极电位关系为uB___uE 。
【单选题】
33测得NPN型三极管上各电极对地电位分别为,,,说明此三极管处在___。
A. 放大区
B. 饱和区
C. 截止区
D. 反向击穿区
【单选题】
34若使三极管具有电流放大能力,必须满足的外部条件是___。
A. 发射结正偏、集电结正偏
B. 发射结反偏、集电结反偏
C. 发射结正偏、集电结反偏
D. 发射结反偏、集电结正偏
【单选题】
35在由PNP晶体管组成的基本共射放大电路中,当输入信号为1KHz、5mV的正弦电压时,输出电压波形出现了顶部削平的失真。这种失真是___ 。
A. 饱和失真
B. 截止失真
C. 交越失真
D. 频率失真
【单选题】
36在由PNP晶体管组成的基本共射放大电路中,当输入信号为1KHz、5mV的正弦电压时,输出电压波形出现了底部削平的失真。这种失真是___ 。
A. 饱和失真
B. 截止失真
C. 交越失真
D. 频率失真
【单选题】
37共集电极放大电路中Re的负反馈组态是___。
A. 电压串联负反馈
B. 电流串联负反馈
C. 电压并联负反馈
【单选题】
38为了使放大器带负载能力强,一般引入___负反馈。
【单选题】
41为了提高三极管放大电路的输入电阻,采用___负反馈 i=i1+i2
【单选题】
42为了稳定输出电流,采用___负反馈。
【单选题】
43为了改善放大器的动态性能,应该引入___电路。
A. 直流负反馈
B. 交流负反馈
C. 电压负反馈
D. 电流负反馈
【单选题】
44为了稳定放大器的静态工作点,应该引入___电路。
A. 直流负反馈
B. 交流负反馈
C. 电压负反馈
D. 电流负反馈
【单选题】
45共模抑制比是差分放大电路的一个主要技术指标,它反映放大电路___能力。
A. 放大差模抑制共模
B. 输入电阻高
C. 输出电阻低
【单选题】
46差分放大电路是为了___而设置的。
A. 稳定Au
B. 放大信号
C. 抑制零点漂移
【单选题】
47分析运放的“虚短”是指是___。
A. U-≈U+
B. I-≈I+≈0
C. U0=Ui
D. U-≈U+≈0
【单选题】
48分析运放的“虚断”是指是___。
A. U-≈U+
B. I-≈I+≈0
C. I-≈I+
D. U-≈U+≈0
【单选题】
51两级放大电路,Au1=-40,Au2=-50,若输入电压U1=5mv,则输出电压Uo为 ___
A. -200mv;
B. -250mV;
C. 10V;
D. 100V
【单选题】
52通用型集成运放的输入级多采用___。
A. 共基接法
B. 共集接法
C. 共射接法
D. 差分接法
【单选题】
53理想运放的两个重要性质是___。
A. 虚短与虚地
B. 虚断与虚短
C. 断路与短路
【单选题】
54振荡器的输出信号最初由___而来的。
A. 基本放大器
B. 选频网络
C. 干扰或噪声信号
【单选题】
55产生正弦波自激震荡的稳定条件是___。
A. 引入正反馈
B. |AF|≥1
C. AF=1
【单选题】
56从结构上来看,正弦振荡电路是一个 ___ 。
A. 有输入信号的负反馈放大器;
B. 没有输入信号的带选频网络的正反馈放大器;
C. 没有输入信号的不带选频网络的正反馈放大器。
【单选题】
57对频率稳定度要求较高的振荡器,要采用: ___ 。
A. LC振荡电路;
B. RC振荡电路;
C. RL振荡电路;
D. 石英晶体振荡电路。
【单选题】
58在甲类、乙类、甲乙类放大电路中,其导通角分别为___
A. 小于180 O、180 O、360O
B. 360O、180 O、小于180 O。
C. 180 O、小于180 O、360O
【单选题】
W78XX系和列W79XX系列引脚对应关系为 ___ 。
A. 一致;
B. 1脚与3脚对调,2脚不变;
C. 1、2对调。
【单选题】
60两个β相同的晶体管组成复合管后,其电流放大系数约为 ___ 。
【单选题】
1三极管的开关特性是___。
A. 截止相当于开关接通
B. 放大相当于开关接通
C. 饱和相当于开关接通
D. 截止相当于开关断开,饱和相当于开关接通
推荐试题
【判断题】
班组的经济核算无论是项目承包或单台总工时的考核,还是按计划,经济地完成任务,都需要以降低成本,提高质量,缩短修理周期为班组的生产目标
【判断题】
轴承预紧的目的是提高轴承支承的刚度,提高轴的旋转精度,降低轴的震动和噪声,降低轴之间的摩擦
【判断题】
转子材质的不均匀将会影响高速机械转子精度
【判断题】
镦粗加工工艺最好用于塑性好,延展性大的金属材料台阶轴或双联齿轮等毛坯件加工
【判断题】
为了保证大型设备基础的承载能力,一般采用钢筋温凝土整体浇灌的结构
【判断题】
多段床身接合面刮削时,将被刮的接合面端用枕木垫高的目的是便于刮研
【判断题】
更换清单,由主管工艺人员提出,由备件人员核定出价格,更换件包括机械,电器,液(气)压的备配件和外购件
【判断题】
任何提高劳动生产率的措施,都必须以经济效益为前提
【判断题】
精密机床导轨在的粗糙度要求是:每25mm×25mm在16~20点
【判断题】
工作台要牢固平稳,平台周围要保持整洁,通行要方便,1米内禁止堆放物件
【判断题】
两孔轴线相交成 90°角,一个孔直径为φ20mm,另一个孔直径是φ30mm,应该先钻穿直径大的孔
【判断题】
碳素工具钢和合金工具钢用于制造中、低速成型刀具
【判断题】
经纬仪整平时,经反复调整,直到仪器转到任意位置时,水准气泡最大偏离值小于二分之一格为止
【判断题】
刮削大型机床导轨面时,应在将导轨面上的零件全部拆除后进行,以保证刮削质量
【判断题】
要安排好培训计划,做好上课的准备工作,做到有组织,有计划地进行培训,做到定时间,定地点,定内容,定进度,定要求,有练习,有考核
【判断题】
轨道制作主要是轨道调直和接头,调直后对轨道进行编号,两条轨道上从端部或伸缩缝处算起,轨道接头至少要对齐,以使运转平稳
【判断题】
为实现电动机连续正转运行需采用具有接触器自锁的控制线路和手动正转控制回路
【判断题】
在修理带传动机构时,发现带轮孔超差额0.08mm,造成配合过松,一般可用镀铬法来加大轴颈尺寸
【判断题】
用经纬仪和平行光管测量机床转台分度误差时,应用专用心轴配装在转台中心孔中将经纬仪和心轴紧固联接在一起
【判断题】
采用双螺母螺纹式调整滚珠丝杠轴向间隙的方法结构紧凑,调整方便,应用广泛
【判断题】
若自准直仪上读数鼓轮每格角值分度值为1",则其线值分度值可用0.05mm/m表示
【判断题】
所有的紫色酒精,在 1 米内不准点有明火,不准放在暖气片上
【判断题】
固定式装配适用于单件和小批量模具的装配,以及装配精度要求较高,需要调整的部位较多的装配
【判断题】
我国对企业发生的事故,坚持“四不放过”原则进行处理
【判断题】
在机械设备中,凸轮表面误差将会引起扭转振动
【单选题】
What happens to the status of users already logged into ESXi Shell when a vSphere administrator enables lockdown mode?___
A. Users remain logged in and can run commands, except to disable lockdown mode.
B. Users remain logged in and can run commands, including disabling lockdown mode.
C. Users are immediately logged out of ESXi Shell.
D. Users are logged out after a timeout specified by the vSphere administrator.
【单选题】
What is the effective vSphere licensing level during the 60 day evaluation period?___
A. vSphere Foundation Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
【单选题】
To comply with security requirements, an administrator with a vCenter Server Appliance needs to force logoff of the vSphere web client after 10 minutes of inactivity.What should the administrator do to meet the requirement?___
A. Edit: /var/lib/vmware/vsphere-client/webclient.properties, modify session.timeout=10
B. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=600
C. Edit: /var/lib/vmware/vsphere-client/webclient.properties modify session.timeout=600
D. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=10
【单选题】
An administrator enables High Availability (HA) on a Virtual SAN cluster.Which network is used for HA Network Heatbeat configuration?___
A. The Management network.
B. The vMotion network.
C. The Virtual SAN network.
D. The Provisioning Traffic network.
【单选题】
A user wants to monitor a business-critical virtual machine to ensure that it doesn't run out of resources. What metric could be monitored in vRealize Operations to address this concern?___
A. Time Remaining badge
B. Compliance badge
C. Reclaimable Waste badge
D. Density badge
【单选题】
An administrator has recently installed a new ESXi 6.x Host, and during the configuration notices sporadic network problems. To check whether the issue occurred sometime during the configuration, the administrator would like to reset the system.How can this be accomplished in the shortest amount of time?___
A. Run the ESXi installer again and reinstall the host.
B. Select the Reset System Configuration option from the vSphere Client when connected directly to the host.
C. From the
D. irect Console User Interface, select Reset System Configuration.
【单选题】
A vApp is running out of compute resources when overall activity is high within the resource pool. At other times, everything is fine.What should be done to resolve this issue?___
A. Increase the size of the resource pool Shares.
B. Set the vApp's CPU and Memory Reservation Type to Expandable.
C. Set the vApp's CPU and Memory Limit to Unlimited.
D. Create a new resource pool with the existing hardware configuration.
【单选题】
A virtual machine has been renamed and an administrator is unable to find files with the new virtual machine name in the datastore.What is the reason for this?___
A. The names of the files on the datastore do not change.
B. The names of the files on the datastore have been corrupted.
C. The virtual machine needs to be re-added to the inventory.
D. The Distributed Resource Scheduler moved the virtual machine to another host.
【单选题】
An administrator has configured network connectivity for a new virtual machine, as shown in the Exhibit.What will occur with the network traffic of this virtual machine when communicating externally from vSwitch1?___
A. The virtual machine will communicate on both uplinks
B. The virtual machine will only communicate on vmnic1
C. The virtual machine will only communicate on vmnic2
D. The virtual machine will fail to communicate externally
【单选题】
An administrator is unable to create the first group in a new vRealize Operations environment. What is the likely cause of the problem?___
A. There are no group types defined.
B. The group is not defined in SSO.
C. There are more than 32 group types defined.
D. The description for the group is not provided.
【单选题】
A new vApp was built and tested in the corporate headquarters datacenter running vSphere 6.x. What condition would explain why the virtual machine is failing to boot in an offsite datacenter running on vSphere 5.5?___
A. The virtual machine was built with the default hardware version.
B. The VMFS 5 datastore is not compatible with virtual machines configured with vSphere 6.x.
C. a
D. RS 5.5 cluster cannot run virtual machines configured with vSphere 6.x.
【单选题】
An administrator is evaluating whether to deploy vCenter Server on a Windows server or on a vCenter Server appliance. The administrator has the following requirements: <A web browser will be utilized to manage the vSphere environment.> <16 ESXi hosts will be deployed.> <Licenses must be shared with a vCenter Server at another site.> <An external Oracle 10g database server will be used to host the vCenter Server database.> Why will the administrator need to deploy vCenter Server on a Windows server?___
A. Linked Mode is a requirement for the solution.
B. Oracle 10g is a requirement for the solution.
C. The vSphere web client is a requirement for the solution.
D. Management of more than 5 hosts is a requirement for the solution.