刷题
导入试题
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,插电式混合动力汽车的纯电动续驶里程应大于等于___。
A. 50km
B. 100km
C. 150km
D. 200km
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,汽车(三轮汽车除外)的车轮定位应与该车型的技术要求一致。对前轴采用非独立悬架的汽车(前轴采用双转向轴时除外),其转向轮的横向侧滑量,用侧滑台检验时侧滑量值应小于等于___。
A. 3m/km
B. 5m/km
C. 10m/km
D. 15m/km
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,总质量大于等于___ 的危险货物运输货车还应装备电控制动系统(EBS)。
A. 6000kg
B. 10000kg
C. 12000kg
D. 15000kg
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,机动车行车制动性能和应急制动性能检验应在平坦、硬实、清洁、干燥且轮胎与地面间的附着系数大于等于___的混凝土或沥青路面上进行。
A. 0.7
B. 0.9
C. 0.5
D. 0.8
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,在空载状态下,驻车制动装置应能保证机动车在坡度为 20%(对总质量为整备质量的 1.2 倍以下的机动车为 15%)、轮胎与路面间的附着系数大于等于 0.7 的坡道上正、反两个方向保持固定不动,时间应大于等于___。
A. 1min
B. 2min
C. 3min
D. 5min
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,机动车应装置后反射器。挂车及车长大于等于___ 的机动车应安装侧反射器和侧标志灯。
A. 6m
B. 9m
C. 10m
D. 11m
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,所有货车(半挂牵引车、多用途货车除外)、货车底盘改装的专项作业车和挂车(旅居挂车除外)应在侧面设置车身反光标识。侧面的车身反光标识长度应大于等于车长的___,对三轮汽车应大于等于1.2m,对侧面车身结构无连续平面的货车底盘改装的专项作业车应大于等于车长的30%,对货厢长度不足车长50%的货车应为货厢长度。
A. 30%
B. 40%
C. 50%
D. 60%
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,机动车(手扶拖拉机运输机组除外)应设置具有连续发声功能的喇叭,喇叭声级在距车前 2m、离地高 1.2m 处测量时,发动机最大净功率(或电机额定功率总和)为 7 kW 以 下 的 摩 托 车 为 80 dB___ ~ 112 dB(A) , 其 他 机 动 车 为( )。
A. 80 dB(A)~90 dB(A)
B. 90 dB(A)~112 dB(A)
C. 90 dB(A)~115 dB(A)
D. 100 dB(A)~115 dB(A)
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,总质量大于等于___ 的货车,应装备符合标准要求的车辆右转弯音响提示装置,并在设计和制造上保证驾驶人不能关闭车辆右转弯音响提示装置。
A. 6000kg
B. 9000kg
C. 10000kg
D. 12000kg
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,乘用车、挂车轮胎胎冠花纹上的花纹深度应大于等于___,摩托车轮胎胎冠花纹上的花纹深度应大于等于 0.8mm;其他机动车转向轮的胎冠花纹深度应大于等于 3.2mm,其余轮胎胎冠花纹深度应大于等于1.6mm。
A. 0.8mm
B. 1.2mm
C. 1.5mm
D. 1.6mm
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,两轮普通摩托车、两轮轻便摩托车的前后轮和边三轮摩托车的主车前后轮中心平面允许偏差应小于等于 ___。
A. 6mm
B. 8mm
C. 10mm
D. 15mm
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,前风窗玻璃驾驶人视区部位及驾驶人驾驶时用于观察外后视镜的部位的可见光透射比应大于等于___。所有车窗玻璃不应张贴镜面反光遮阳膜。
A. 50%
B. 60%
C. 70%
D. 80%
【单选题】
纯电动汽车、插电式混合动力汽车在车辆起步且车速低于___ 时, 应能给车外人员发出适当的提示性声响。
A. 10km/h
B. 20km/h
C. 30km/h
D. 50km/h
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,所有汽车(三轮汽车、五轴及五轴以上专项作业车除外)及总质量大于___ 的挂车应装备符合规定的防抱制动装置。
A. 1500kg
B. 2500kg
C. 3500kg
D. 4500kg
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,液压行车制动在达到规定的制动效能时,踏板行程应小于等于踏板全行程的___, 制动器装有自动调整间隙装置的机动车踏板行程应小于等于踏板全行程的五分之四,且乘用车应小于等于 120mm,其他机动车应小于等于 150mm。
A. 三分之二
B. 四分之一
C. 四分之三
D. 五分之四
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,汽车的制动协调时间,对液压制动的汽车应小于等于___,对气压制动的汽车应小于等于 0.60s。
A. 0.35s
B. 0.45s
C. 0.60s
D. 0.80s
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,铰接客车、铰接式无轨电车的制动协调时间应小于等于___。
A. 0.35s
B. 0.45s
C. 0.60s
D. 0.80s
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,进行制动力检验时,汽车、汽车列车各车轮的阻滞力均应小于等于轮荷的___。
A. 5%
B. 10%
C. 8%
D. 3%
【单选题】
《机动车运行安全技术条件》(GB7258-2017)规定,车长大于等于___的客车应具有超速报警功能,当行驶速度超过允许的最大行驶速度(允许的最大行驶速度不应大于100km/h)时能通过视觉和声觉信号报警,但具有符合规定的限速功能或限速装置的除外。
A. 6m
B. 7m
C. 9m
D. 12m
【单选题】
《机动车查验工作规程》(GA801-2019)规定,对客车、危险货物运输货车、半挂牵引车和总质量大于或等于___的其他货车,查验行驶记录装置。
A. 10000kg
B. 12000kg
C. 15000kg
D. 20000kg
【单选题】
《机动车查验工作规程》(GA801-2019)规定,进口机动车注册登记,专项作业车、挂车、中型(含)以上载客汽车、中型(含)以上载货汽车的注册登记和变更登记(变更迁出除外),危险货物运输车辆的所有登记业务,以及申领机动车登记证书和校车使用许可、报废机动车法定监督解体、嫌疑车辆调查取证等业务的机动车查验应由___负责。
A. 外观员
B. 审核员
C. 民警查验员
D. 初级查验员
【单选题】
《机动车查验工作规程》(GA801-2019)规定,先行核发机动车检验合格标志后监督检查的,机动车安全技术检验远程视频监管中心应在检验照片(或视频)上传后的___内将检验照片(或视频)比对完毕;采用了符合规定的机动车检验智能审核监管方式的,按比例抽查。比对结果表明检验项目不符合 GB7258 国家标准及其他相关规定的,应要求机动车安全技术检验机构通知送检的机动车重新进行检验,并按规定对机动车安全技术检验机构予以处罚。
A. 1 h
B. 12 h
C. 24 h
D. 48 h
【单选题】
汽车一般由发动机、___、车身、电气和电子设备四大部分组成。
A. 底盘
B. 变速箱
C. 离合器
D. 驾驶室
【单选题】
目前汽车用代用燃料主要有:合成液体石油、___、压缩天然气(CNG)、醇类等燃料。
A. 汽油
B. 液化石油气(LPG)
C. 柴油
D. 蓄电池
【单选题】
发动机按工作方式分,有___和四冲程两种,一般发动机为四冲程发动机。
A. 二冲程
B. 三冲程
C. 五冲程
D. 六冲程
【单选题】
通常讲的发动机排气量指的是___。
A. 气缸总容积
B. 燃烧室容积
C. 气缸工作容积
D. 活塞行程
【单选题】
行驶系统包括:支撑全车的承载式车身及副车架、悬架和___等部分。
A. 车轮
B. 离合器
C. 半轴
D. 变速器
【单选题】
转向盘在空转阶段中的___称为转向盘自由行程。
A. 距离
B. 角行程
C. 长度
D. 半径
【单选题】
轮胎标志为 205/ 75R15,这里 205 表示___。
A. 断面宽度(cm)
B. 轮辋直径(cm)
C. 轮辋直径(inch)
D. 断面宽度(mm)
【单选题】
轮胎标志为 205/ 75R15,这里 75 表示___。
A. 扁平比
B. 轮辋直径(cm)
C. 轮辋直径(inch)
D. 轮胎宽度(mm)
【单选题】
轮胎标志为 205/ 75R15,这里 15 表示___。
A. 轮辋直径(mm)
B. 轮辋直径(cm)
C. 轮辋直径(inch)
D. 轮胎宽度(cm)
【单选题】
轮胎标志为 205/ 75R15,这里R 表示___。
A. 斜交胎
B. 子午线胎
C. 轮辋直径(inch)
D. 断面宽度(mm)
【单选题】
目前各类机动车所用的摩擦制动器可分为鼓式和___两大类。
A. 机械式
B. 气压式
C. 手动式
D. 盘式
【单选题】
按照GB21861-2014的规定:对于不适用于仪器设备制动检验的车辆,用制动距离或者___判定制动性能。
A. 最大减速度和制动协调时间
B. 充分发出的最大减速度和制动协调时间
C. 充分发出的平均减速度和制动时间
D. 充分发出的平均减速度和制动协调时间
【单选题】
依据“GB21861-2014”对非营运小型、微型载客汽车车辆底盘部件检查工位的最少检验时间为___s。
A. 40
B. 60
C. 100
D. 180
【单选题】
按照GB21861-2014的规定:对已在制动检验台上检验过的车辆,制动力平衡及前轴制动率符合要求,但整车制动率未达到合格要求时,用便携式制动性能测试仪检测,对于小(微)型载客汽车及其它总质量不大于 4500kg 的汽车的制动初速度应___。
A. 不低于 20km/h
B. 不低于 30km/h
C. 不低于 50km/h
D. 不高于 30km/h
【单选题】
侧滑检验台是汽车在滑动板上驶过时,用测量滑动板左右___的方法来测量车轮滑移量的大小和方向,并判断是否合格的一种检测设备。
A. 移动量
B. 滑动率
C. 阻力
D. 驱动力
【单选题】
前照灯远近光一体检测仪检测时对车辆停放距离要求一般是___。
A. 2 米
B. 2.5 米
C. 1 米
D. 0.5 米
【单选题】
检测设备最大负荷指被测车辆的___。
A. 整车质量
B. 单轮最大轮荷
C. 单轴最大轴荷
D. 3 轮质量
【单选题】
常用侧滑检验台为带放松板的()型式。
A. 单板单动
B. 双板联动
C. 双板连体单动
D. 双板分体分动
【单选题】
常用侧滑检验台的测量范围为___。
A. ±10m/km
B. ±8 m/km
C. ±12 m/km
D. ±5m/km
推荐试题
【单选题】
Which about nested policy maps in a zone-based firewall is true ?___
A. They are limited to two leve ls in a hierarchical policy
B. Parent policies are previously defined policies that are defined by using the service policy command
C. A child policy is a new policy that uses a pre-existing policy.
D. A child policy is a new that uses a pre-existing policy
【单选题】
In which configuration do you configure the ip ospf authentication key 1 command?___
A. routing process
B. interface
C. privileged
D. global
【单选题】
Which statement about command authorization and security contexts is true?___
A. If command authorization is configured, it must be enabled on all contexts.
B. The change to command invokes a new context session with the credentials of the currently
C. AAA settings are applied on a per-context basis
D. The enable. 15 user ang admins with chang to permission ha e dfferent command authorization levels pertontext
【单选题】
Which command do you enter to enable authentication for OSPF on an interface?___
A. router(config-if)#ip ospf message-digest-key 1 md5 CIS COPASS
B. router(config-if)#ip ospf authentication message-digest
C. router(config-if)#ip ospf authentication-key CISCOPASS
D. router(config-if)#area 0 authentication message-digest
【单选题】
What feature defines a campus area network?___
A. It has a single geographic location
B. It lacks external connectivity.
C. It has a limited number of segments.
D. It has limited or restricted Internet access
【单选题】
Which type of attack most commonly involves a direct attack on a network?___
A. :phishing
B. Trojan horse
C. denial of service
D. social engineering
【单选题】
What information does the key length provide in an encryption algorithm?___
A. the cipher block size
B. the hash bloc k size
C. the number of permutations
D. the packet size
【单选题】
How do you verify TaCACS+ connectivity to a device?___
A. You successfully log in to the device by using the local credentials
B. You connect via console port and receive the login prompt.
C. You connect to the device using SSH and receive the login prompt.
D. You successfully log in to the device by using ACS credentials
【单选题】
Which term best describes the concept of preventing the modification of data in transit and in storage?___
A. availability
B. confidentially
C. fidelity
D. integrity
【单选题】
Which loS command is used to define the authentication key for ntp?___
A. switch(config )#ntp authentication-key 1 mds Clcs
B. switch(config )#ntp authenticate
C. switch(config)#ntp trusted-key 1
D. switch(config)#ntp source 192.168.0.1
【单选题】
What is true about the cisco lOS Resilient Configuration feature ?___
A. The feature can be disabled through a remote session
B. There is additional space required to secure the primary cisco lOS image file.
C. The feature automatically detects image or configuration version mismatch.
D. Remote storage is used for securing files
【单选题】
When is the default deny all policy an exception in zone-based firewalls?___
A. when traffic terminates on the router via the self zone
B. when traffic traverses two interfaces in different zones
C. when traffic traverses two interfaces in the same zone
D. when traffic sources from the router via the self zone
【单选题】
.If an access port is assigned as an isolated port in a PVLAN, which network ports can it communicate with?___
A. promiscuous ports in the same PLVAN
B. isolated ports in the same PVLAN
C. all ports in the same PAVLAN at ILAR
D. all ports in the adjacent PVLAN
【单选题】
Which IPSEC mode is used to encypt traffic directly between a client and a server VPN endpoint?___
A. quick mode
B. transport mode
C. aggressive mode
D. tunnel mode
【单选题】
Which command do you enter to verify that a vpn connection is established between two endpoints and that the connection is passing traffic? ___
A. Firewall#sh crypto session
B. Firewall#debug crypto isakmp
C. Firewall#tsh crypto ipsec sa
D. Firewall#sh crypto isakmp sa
【单选题】
which type of Pvlan port allows communication from all port types?___
A. isolated
B. in -line
C. community
D. promiscuous
【单选题】
Which command do you enter to configure your firewall to conceal internal addresses?___
A. no ip directed-broadcast
B. no ip logging facility
C. no proxy-arp
D. no ip inspect audit-trial
E. no ip inspect
F. route
【单选题】
Which feature defines a campus area network? ___
A. It has a limited number of segments.
B. It has limited or restricted Internet access
C. It lacks ex1ternal connectivity.
D. It has a single geographic location
【单选题】
What technology can you use to provide data confidentiality data integrity and data origin authentication on your network?___
A. IPSec
B. Certificate Authority
C. IKE
D. Data
E. ncryption Standards
【单选题】
which standard is a hybrid protocol that uses oakley and skerne ke y exchanges is an ISAKMP framework?___
A. SHA
B. IPSec
C.
D. ES
【单选题】
What is the actual los privilege level of User Exec mode?___
A. 1
B. 0
C. 5
D. 15
【单选题】
What is the effect of the asa command crypto isakmp nat-traversal?___
A. It opens port 500 only on the out side interface
B. It opens port 500 only on the inside interface
C. It opens port 4500 on all interfaces that are IPSec enabled
D. It opens port 4500 only on the out side interfac
【单选题】
Which Fire POWER preproce ssor engine is used to prevent SYN attacks?___
A. Inline normalization
B. IP Defragmentation
C. Ports can
D. etection
【单选题】
Which NAT type allows objects or groups to reference an IP address ?___
A. identity NAt
B. static NAT
C. dynamic
D. dynamic NAT
【单选题】
Which Auto NAT policies are processed first?___
A. Dynamic NAT with longest prefix
B. Dynamic NAT with shortest prefix
C. static NAT with longest prefix
D. static NAT with shortest prefix
【单选题】
Which feature allows a dynamic Pat pool to se lect the next address in the pat pool instead of the next port of an existing address?___
A. next IP
B. round robin
C. dynamic rotation
D. NAT address rotation
【单选题】
Which IPS detection method can you use to detect attacks that are based on the attackers IP address?___
A. anomally-based
B. policy-based
C. signature-based
D. reputation-based
【单选题】
Which type of encryption technology has the broadest platform support?___
A. software
B. middleware
C. file-level
D. hardware
【单选题】
Which type of address translation supports the initiation of comm unications bidirectionally ?___
A. multi-session PAT
B. dynamic NAT
C. dynamic PAT
D. static NAT
【单选题】
Which label is given to a person who uses existing computer scripts to hack into computers while lacking the expertise to write the own?___
A. script kiddy
B. white hat hacker
C. hacktivist
D. phreaker
【单选题】
What is the primary purpose of a defined rule in an IPS?___
A. to configure an event action that takes place when a signature is triggered
B. to define a set of actions that occur when a specific user logs in to the system
C. to configure an event action that is pre-defined by the system administrator
D. to detect internal attacks
【单选题】
Which option is the default valuce for the Diffie- Hell man group when configuring a site-to-site VPn on an asa device ?___
A. Group 1
B. Group 2
C. Group 5
D. Group 7
【单选题】
Which feature filters CoPP packets?___
A. access control lists
B. class maps
C. policy maps
D. route maps
【单选题】
Which command is used in global configuration mode to enable AAA?___
A. configure-model aaa
B. configure aaa-modelA
C. aaa new-model
D. aaa
E. XEC
【单选题】
Which statement about the given configuration is true?___
A. The single-connection command causes the device to establish one connection for all TACACS
B. The single-connection command causes the device to process one TacAcs request and then move to the next server
C. The timeout com mand causes the device to move to the next server after 20 seconds of TACACS inactive
【多选题】
What are two well-known security terms?___
A. phishing//网络钓鱼
B. ransomware //勒索软件
C. BPDU guard
D. LACP
E. hair-pinning
【多选题】
Which two commands must you enter to securely archive the primary bootset of a device___
A. router(config )#secure boot-config
B. router(config)#auto secure
C. router(config)#secure boot-image
D. router(config)#service passw ord-encryption
【多选题】
Which two functions can SIEM provide ?___
A. correlation between logs and events from multiple systems
B. event aggregation that allows for reduced log storage requirements
C. proactive malware analysis to block malicious traffic
D. dual-factor authentication
E. centralized firewall management
【多选题】
Which two features of Cisco Web Reputation tracking can mitigate web-based threats?___
A. buffer overflow filterin dhsuowip
B. Bayesian filters
C. web reputation filters
D. outbreak filtering
E. exploit filtering
【多选题】
What are two challenges when deploying host- level IPS? ___
A. The deployment must support multiple operating systems.
B. It is unable to provide a complete networ k picture of an attack.
C. It is unable to determine the outcome of e very attack that it detects
D. It does not provide protection for offsite computers
E. It is unable to detect fragmentation attacks
欢迎使用我爱刷题
×
微信搜索我爱刷题小程序
温馨提示
×
请在电脑上登陆“www.woaishuati.com”使用