【单选题】
6502电气集中在办理取消进路和人工解锁时，_______在进路未解锁前一直保持吸起。[322020201]___
A. ZQJ
B. ZRJ
C. QJ
D. LAJ
查看试卷，进入试卷练习
微信扫一扫，开始刷题
相关试题
【单选题】
6502电气集中在排列进路过程中，进路始端按钮表示灯在_______熄灭。[322020201]___
A. 进路锁闭后
B. XJ吸起后
C. 方向电源无电后
D. 选路完毕后
【单选题】
6502电气集中调车XJJ在_______时，XJJ1-2线圈自闭电路接在8网络线上。[322020201]___
A. JYJ落下、QJ吸起
B. JYJ吸起
C. XJ吸起
D. QJ落下
【单选题】
6502电气集中在12线上串接QJJ第二组接点其作用是_______。[322020201]___
A. 防止提前解锁
B. 防止道岔中途转换
C. 防止迂回电流
D. 保证供电
【单选题】
办理人工解锁时，QJ的落下时机是_______。[321020201]___
A. KF-ZQJ-Q无电→QJ↓
B. 1RJJ↑→QJ↓
C. XJJ↓→QJ↓
D. KZ-RJ-H无电→QJ↓
【单选题】
6502电气集中KJ复原的时机是_______。[322020201]___
A. 进路内第一个道岔区段解锁后
B. 进路锁闭后
C. 信号开放后
D. 进路内所有的区段解锁后
【单选题】
接车方向的并置调车信号机作阻拦信号，此时ZJ吸起所检查的条件电源是_______。[32202021]___
A. KF-DFJ-Q
B. KF-DJJ-Q
C. KF-列共-DJJ-Q
D. KF-共用-Q
【单选题】
按压接车方向调车信号机按钮后可供下列电源中的_______。[321020201]___
A. KZ-列共-Q
B. KZ-共用-Q
C. KF-DJJ-Q
D. KF-DFJ-Q
【单选题】
进路排列表示灯电路中并接有四个方向继电器的第_______接点。[321020201]___
【单选题】
5/72DCJ自动复原的条件是_______。[321020201]___
A. 5/71SJ落下
B. 5/72SJ落下
C. KZ-ZQJ-H有电
D. KF-共用-Q有电
【单选题】
办理D3往IG的长调车进路时，有关的FKJ、KJ动作顺序应是_______。[321020201]___
A. FKJ自左向右，KJ自右向左顺序吸起
B. FKJ、KJ均为自左向右顺序吸起
C. FKJ、KJ均为自右向左顺序吸起
D. FKJ自右向左，KJ自左向右顺序吸起
【单选题】
在选双动道岔反位时，1DQJ的励磁条件是通过_______的接点接入KF。[322020201]___
A. 1FCJ62
B. 1DCJ63
C. 2FCJ62
D. 2DCJ63
【单选题】
在分线盘上X1(或X2)与X3线端子测电压判断道岔表示故障，当交流2V左右、直流为0V时，可判断为_______。[333020201]___
A. 室外二极管击穿短路
B. 室外断线
C. 室内断线
D. 电容短路
【单选题】
接车方向单置调车信号机按钮作为发车方向调车进路变通按钮时，其AJ用_______作为励磁条件之一。[332000000]___
A. KF-共用-Q
B. KF-DFJ-Q
C. KZ-列共-DJJ-Q
D. KZ-列共-DFJ-Q
【单选题】
6502电气集中四线制道岔定位无表示，定位表示继电器颤动，说明_______。[333020201]___
A. 室外开路
B. 室内表示电路电容故障
C. 室内继电器开路
D. 室外二极管开路
【单选题】
6502电气集中DXJ复原的时机是_______。[322020201]___
A. 进路内第一个道岔区段解锁后
B. 进路锁闭后
C. 信号开放后
D. 进路内所有的区段解锁后
【单选题】
发车方向单置调车信号机按钮作为接车方向调车进路变通按钮时，其AJ用_______为励磁条件之一。[332010201]___
A. KF-共用-Q
B. KF-DFJ-Q
C. KZ-列共-LFJ-Q
D. KZ-列共-DJJ-Q
【单选题】
6502电气集中列车信号继电器的缓放是靠_______。[322020201]___
A. 一般继电器
B. 缓入型继电器
C. 阻容元件
D. 电感
【单选题】
在控制台中，股道上最短的光带不得少于_______单元。[321010201]___
【单选题】
6502电路选岔电路中，能证明整条进路已被全部选出而励磁吸起的继电器是_______。[323020201]___
A. ZJ
B. 最左端的JXJ
C. 最右端的JXJ
D. FKJ
【单选题】
6502电路中传递继电器的1-2线圈在_______的情况下起作用。[322020201]___
A. 取消解锁
B. 正常解锁
C. 故障解锁
D. 调车中途返回解锁
【单选题】
单置调车信号机按钮作始端使用时，_______吸起。[321020201]___
A. AJ、2AJ
B. 1AJ、AJ
C. 1AJ、2AJ、AJ
D. 1AJ、2AJ
【单选题】
6502电气集中进路选择继电器JXJ吸起后，在_______时复原。[321020201]___
A. 始端按钮继电器落下
B. 终端按钮继电器落下
C. KF-共用-Q断电
D. 道岔操纵继电器落下
【单选题】
6502电气集中9网络线的正极性电源KZ是从_______接入。[321020201]___
A. 进路左边
B. 进路右边
C. 进路始端
D. 进路终端
【单选题】
6502电气集中调车信号继电器DXJ受_______控制。[321020201]___
A. 8线
B. 8线和11线
C. 9线
D. 11线
【单选题】
6502电气集中列车信号继电器LXJ受_______控制。[321020201]___
A. 8线
B. 8、11线
C. 9线
D. 11线
【单选题】
进路在锁闭状态时，进路上的道岔不应再转换，此时对道岔实行的锁闭为_______。[322020201]___
A. 区段锁闭
B. 故障锁闭
C. 进路锁闭
D. 引导总锁闭
【单选题】
左向运行的进站信号机列车信号主组合的类型图应选用_______。[321020201]___
A. A-1/LXZ
B. A-2/LXZ
C. B-1/LXZ
D. B-2/LXZ
【单选题】
对于_______的车站，组合的排列顺序应选用“S”型排列法。[321030203]___
A. 咽喉区道岔群数目较大
B. 咽喉区道岔群数目较小
C. 咽喉区距离较短
D. 咽喉区距离较长
【单选题】
QJ平时处于_______状态。[321020201]___
【单选题】
凡是进路的始端部位都应设_______取消继电器QJ。[321030101]___
【单选题】
调车信号辅助组合DXF主要用于_______。[321020201]___
A. 调车信号机
B. 尽头型调车信号机
C. 单置调车信号机及变通按钮
D. 差置调车信号机
【单选题】
进站信号机点灯电路共有_______线。[322020201]___
A. 8条
B. 9条
C. 12条
D. 14条
【单选题】
在有二个发车方向时，出站兼调车信号机应选用_______组合。[321020201]___
A. LXZ
B. 1LXF
C. LXZ、1LXF
D. LXZ、2LXF
【单选题】
列车信号主组合LXZ共有六张类型图，其图号A-2/LXZ中“A”表示_______。[321030204]___
A. 进站
B. 出站
C. 一个发车方向
D. 二个发车方向
【单选题】
根据平行进路断线法规律，优先道岔在左侧，撇型道岔断开_______控制电源。[321020201]___
【单选题】
单动道岔组合共有四张类型图，其中弯股(反位)在上直股在下，且是第一笔道岔的图号为_______。[321030204]___
A. 1/DD
B. 2/DD
C. 3/DD
D. 4/DD
【单选题】
6502电气集中5、6线上串有下列三组继电器接点正确的是_______。[321020201]___
A. QJJ、XJJ、DGJ
B. QJJ、CJ、DGJ
C. QJJ、CJ、FDGJ
D. QJ、CJ、DGJ
【单选题】
列车开始继电器LKJ自闭电路中并有_______继电器接点。[321030203]___
【单选题】
信号检查继电器XJJ利用8线上串接KJ后接点和ZJ后接点来实现_______。[322020201]___
A. 本咽喉没有建立敌对进路
B. 另一咽喉区没未建立敌对进路
C. 选排一致
D. 本咽喉没有建立进路
【单选题】
道岔启动电路中1DQJ的1-2线圈串入道岔动作电路的作用有_______。[321020201]___
推荐试题
【单选题】
A user wants to monitor a business-critical virtual machine to ensure that it doesn't run out of resources. What metric could be monitored in vRealize Operations to address this concern?___
A. Time Remaining badge
B. Compliance badge
C. Reclaimable Waste badge
D. Density badge
【单选题】
An administrator has recently installed a new ESXi 6.x Host, and during the configuration notices sporadic network problems. To check whether the issue occurred sometime during the configuration, the administrator would like to reset the system.How can this be accomplished in the shortest amount of time?___
A. Run the ESXi installer again and reinstall the host.
B. Select the Reset System Configuration option from the vSphere Client when connected directly to the host.
C. From the
D. irect Console User Interface, select Reset System Configuration.
【单选题】
A vApp is running out of compute resources when overall activity is high within the resource pool. At other times, everything is fine.What should be done to resolve this issue?___
A. Increase the size of the resource pool Shares.
B. Set the vApp's CPU and Memory Reservation Type to Expandable.
C. Set the vApp's CPU and Memory Limit to Unlimited.
D. Create a new resource pool with the existing hardware configuration.
【单选题】
A virtual machine has been renamed and an administrator is unable to find files with the new virtual machine name in the datastore.What is the reason for this?___
A. The names of the files on the datastore do not change.
B. The names of the files on the datastore have been corrupted.
C. The virtual machine needs to be re-added to the inventory.
D. The Distributed Resource Scheduler moved the virtual machine to another host.
【单选题】
An administrator has configured network connectivity for a new virtual machine, as shown in the Exhibit.What will occur with the network traffic of this virtual machine when communicating externally from vSwitch1?___
A. The virtual machine will communicate on both uplinks
B. The virtual machine will only communicate on vmnic1
C. The virtual machine will only communicate on vmnic2
D. The virtual machine will fail to communicate externally
【单选题】
An administrator is unable to create the first group in a new vRealize Operations environment. What is the likely cause of the problem?___
A. There are no group types defined.
B. The group is not defined in SSO.
C. There are more than 32 group types defined.
D. The description for the group is not provided.
【单选题】
A new vApp was built and tested in the corporate headquarters datacenter running vSphere 6.x. What condition would explain why the virtual machine is failing to boot in an offsite datacenter running on vSphere 5.5?___
A. The virtual machine was built with the default hardware version.
B. The VMFS 5 datastore is not compatible with virtual machines configured with vSphere 6.x.
C. a
D. RS 5.5 cluster cannot run virtual machines configured with vSphere 6.x.
【单选题】
An administrator is evaluating whether to deploy vCenter Server on a Windows server or on a vCenter Server appliance. The administrator has the following requirements: <A web browser will be utilized to manage the vSphere environment.> <16 ESXi hosts will be deployed.> <Licenses must be shared with a vCenter Server at another site.> <An external Oracle 10g database server will be used to host the vCenter Server database.> Why will the administrator need to deploy vCenter Server on a Windows server?___
A. Linked Mode is a requirement for the solution.
B. Oracle 10g is a requirement for the solution.
C. The vSphere web client is a requirement for the solution.
D. Management of more than 5 hosts is a requirement for the solution.
【单选题】
What is a benefit of using VMware Data Protection ?___
A. Provides support for guest-level backups and restores of Microsoft SQL Servers, Exchange Servers, and Share Point Servers.
B. Provides support for advanced storage services including replication, encryption, deduplication, and compression.
C. Provides direct access to VDP configuration integrated into the vSphere Client.
D. Reduces disk space consumed by virtual machine data using deduplication.
【单选题】
An administrator enables vSphere High Availability (HA) on an existing cluster with a large number of hosts and virtual machines. The administrator notices that the setup of vSphere HA on some of the hosts is failing. What step, if taken, might resolve this issue?___
A. Increase the value of the config.vpxd.das.electionWaitTimeSec setting.
B. Set the value of vpxd.das.aamMemoryLimit to 256.
C. Set the value of the das.useDefaultIsolationAddress setting to False.
D. Increase the value of the das.iostatsinterval setting.
【单选题】
An ESXi 6.x host consists of 24 logical cores. Hyperthreading is enabled on the host. What is the maximum number of vCPUs that can be assigned to a virtual machine on this host?___
【单选题】
By default, each ESXi 6.x host is provisioned with a certificate from which root certificate authority?___
A. RedHat Certificate Authority
B. VMware Certificate Authority
C. DigiCert Certificate Authority
D. Verisign Certificate Authority
【单选题】
An administrator is adding an NFS datastore as shown in the Exhibit. What is the purpose of the Servers to be added list?___
A. It contains the IP addresses of the NFS Storage Server to provide multipathing capability.
B. It contains the IP addresses of the ESXi hosts that mount the datastore.
C. It contains the IP addresses used for
D. ynamic Discovery of targets.
【单选题】
An administrator reports that the System Event log data is only available for 24 hours when reviewing the Hardware Status tab. Which condition could be responsible for the loss of data?___
A. A Reset event log was executed.
B. The statistical collection level was set to a value of 1.
C. The boot disk of the host is corrupt.
D. Syslog has been configured at the vCenter Server level.
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
