刷题
导入试题
【单选题】
装设柱上开关(包括柱上断路器、柱上负荷开关)的配电线路停电,应___。送电操作顺序与此相反。
A. 先断开柱上开关,后拉开隔离开关(刀闸)
B. 先拉开隔离开关(刀闸),后断开柱上开关
C. 先停主线开关,后停支线柱上开关
D. 先停支线柱上开关,后停主线开关
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
配电变压器停电,应___。送电操作顺序与此相反
A. 先拉开高压侧熔断器,后拉开低压侧开关(刀闸)
B. 先拉开低压侧开关(刀闸),后拉开高压侧熔断器
C. 先拉开低压侧分路开关,后拉开低压侧总开关
D. 先拉开低压侧总开关,后拉开低压侧分路开关
【单选题】
摘挂跌落式熔断器的熔管,应使用___,并派人监护。
A. 绝缘棒
B. 验电器
C. 操作杆
D. 专用工具
【单选题】
砍剪靠近带电线路的树木,___应在工作开始前,向全体作业人员说明电力线路有电。
A. 工作负责人
B. 工作许可人
C. 工作票签发人
D. 专业室领导
【单选题】
砍剪靠近带电线路的树木,工作负责人应在工作开始前,向全体作业人员说明电力线路有电;人员、树木、绳索应与导线保持10kV___m的安全距离。
A. 0.7
B. 1.0
C. 1.5
D. 3.0
【单选题】
为防止树木(树枝)倒落在线路上,应使用绝缘绳索将其拉向与线路___的方向,绳索应有足够的长度和强度,以免拉绳的人员被倒落的树木砸伤。
A. 相反
B. 60°
C. 90°
D. 相同
【单选题】
上树时,应使用安全带,安全带不得系在待砍剪树枝的___附近或以上。不得攀抓脆弱和枯死的树枝;不得攀登已经锯过或砍过的未断树木。
A. 茎部
B. 断口
C. 枝丫
D. 根部
【单选题】
使用油锯和电锯的作业,应由___的人员操作。使用时,应先检查所能锯到的范围内有无铁钉等金属物件,以防金属物体飞出伤人。
A. 熟悉工作组人员
B. 熟悉操作方法
C. 熟悉机械性能
D. 熟悉机械性能和操作方法
【单选题】
登杆塔前,应核对___。
A. 杆号
B. 线路名称和杆号
C. 杆基
D. 线路名称
【单选题】
遇有冲刷、起土、上拔或导地线、拉线松动的杆塔,登杆塔前,应先___,打好临时拉线或支好架杆。
A. 培土加固
B. 三交待
C. 两穿一戴
D. 测量接地电阻
【单选题】
攀登杆塔过程中应检查___和金具锈蚀情况。
A. 纵向裂纹
B. 横向裂纹
C. 裂纹
D. 绝缘子污染
【单选题】
在人员密集或有人员通过的地段进行杆塔上作业时,___下方应按坠落半径设围栏或其它保护措施。
A. 杆塔
B. 杆上人员
C. 作业点
D. 横担
【单选题】
作业人员攀登杆塔时,手扶的构件应___。
A. 牢固
B. 方便
C. 灵活
D. 耐用
【单选题】
在杆塔上使用梯子或临时工作平台,应将两端与固定物可靠连接,一般应由___人在其上作业。
A. 一
B. 二
C. 三
D. 四
【单选题】
立、撤杆应设专人统一指挥。开工前,应交待施工方法、指挥信号和___。
A. 安全措施
B. 技术措施
C. 组织措施
D. 应急措施
【单选题】
立、撤杆塔时,禁止基坑内有人。除指挥人及指定人员外,其他人员应在杆塔高度的___倍距离以外。
A. 1.1
B. 1.2
C. 1.3
D. 1.4
【单选题】
使用临时拉线时,一个锚桩上的临时拉线不得超过___。
A. 一根
B. 两根
C. 三根
D. 四根
【单选题】
利用已有杆塔立、撤杆,应检查杆塔___及拉线和杆塔的强度,必要时应增设临时拉线或采取其他补强措施。
A. 基础
B. 根部
C. 中部
D. 上部
【单选题】
使用吊车立、撤杆塔,钢丝绳套应挂在电杆的___以防止电杆突然倾倒。
A. 中间位置
B. 根部
C. 上部
D. 适当位置
【单选题】
使用倒落式抱杆立、撤杆时,主牵引绳、尾绳、杆塔中心及抱杆顶应在一条直线上,抱杆下部应固定牢固,抱杆顶部应设临时拉线,并由___均匀调节控制。
A. 安全监护人
B. 技术人员
C. 工作负责人
D. 有经验的人员
【单选题】
在带电线路、设备附近立、撤杆塔,杆塔、拉线、临时拉线、起重设备、起重绳索应与带电线路、设备保持表6-1所规定的安全距离,且应有防止___接近带电导线的措施。
A. 立杆过程中拉线跳动和杆塔倾斜
B. 立、撤杆过程中拉线跳动和杆塔倾斜
C. 立、撤杆过程中拉线跳动
D. 撤杆过程中拉线杆塔倾斜
【单选题】
在110kV带电设备附近立、撤杆塔,杆塔、拉线、临时拉线、起重设备、起重绳索应与带电线路、设备保持的最小安全距离为___m。
A. 3
B. 4
C. 5
D. 6
【单选题】
在35kV带电设备附近立、撤杆塔,杆塔、拉线、临时拉线、起重设备、起重绳索应与带电设备保持的最小安全距离为___ m。
A. 3
B. 4
C. 5
D. 6
【单选题】
在交叉跨越各种线路、铁路、公路、河流等地方放线、撤线,应先取得有关主管部门同意,做好跨越架搭设、封航、封路、在路口设专人持___看守等安全措施。
A. 信号旗
B. 警示标志
C. 对讲机
D. 荧光棒
【单选题】
交叉跨越各种线路、铁路、公路、河流等放、撤线时,应先取得___同意,做好跨越架搭设、封航、封路、在路口设专人持信号旗看守等安全措施。
A. 主管部门
B. 上级部门
C. 经信部门
D. 交通部门
【单选题】
拆除杆上导线前,应检查___,做好防止倒杆措施,在挖坑前应先绑好拉绳。
A. 卡盘
B. 拉线
C. 埋深
D. 杆根
【单选题】
放线、紧线时,处理有卡、挂现象,应松线后处理。处理时操作人员应站在卡线处___。
A. 内侧
B. 外侧
C. 下方
D. 上方
【单选题】
放线、紧线与撤线时,作业人员不应站在或跨在已受力的牵引绳、导线的___,展放的导线圈内以及牵引绳或架空线的垂直下方。
A. 外角侧
B. 内角侧
C. 上方
D. 受力侧
【单选题】
___采用突然剪断导线的做法松线。
A. 原则上不得
B. 可以
C. 禁止
D. 在保障安全前提下可
【单选题】
架空绝缘导线不得视为___。
A. 绝缘设备
B. 导电设备
C. 承力设备
D. 载流设备
【单选题】
邻近带电导线的工作中,应使用绝缘无极绳索,风力应小于___ 级,并设人监护。
A. 4
B. 5
C. 6
D. 7
【单选题】
在带电杆塔上进行测量、防腐、巡视检查、紧杆塔螺栓、清除杆塔上异物等工作,风力应小于___级。配电《安规》
A. 6
B. 5
C. 4
D. 3
【单选题】
若停电检修的线路与另一回带电线路___,并导致工作时人员和工器具可能和另一回线路接触或接近至表5-1规定的安全距离以内,则另一回线路也应停电并接地。
A. 交叉
B. 平行
C. 同杆架设
D. 交叉或接近
【单选题】
邻近10kV带电线路工作时,人体、导线、施工机具等与带电线路的距离应满足___ m要求。
A. 1.0
B. 0.7
C. 0.4
D. 0.9
【单选题】
在110kV带电线路下方进行交叉跨越档内松紧、降低或架设导线的检修及施工,应采取防止导线跳动或过牵引与带电线路接近至___ m安全距离的措施。
A. 2
B. 2.5
C. 3.0
D. 3.5
【单选题】
同杆(塔)架设多回线路中部分线路停电的工作时,工作票中应填写多回线路中每回线路的___。
A. 双重称号
B. 双重名称
C. 位置称号
D. 线路名称
【单选题】
在带电导线附近使用绑线时,应在下面绕成小盘再带上杆塔。禁止在杆塔上___。
A. 卷绕或放开绑线
B. 卷绕绑线
C. 放开绑线
D. 使用绑线
【单选题】
柱上变压器台架工作,若变压器的低压侧无法装设接地线,应采用___措施。
A. 禁止工作
B. 加强监护
C. 拆除引线
D. 绝缘遮蔽
【单选题】
不宜在跌落式熔断器___新装、调换引线,若必须进行,应采用绝缘罩将跌落式熔断器上部隔离,并设专人监护。
A. 上部
B. 下部
C. 左侧
D. 右侧
【单选题】
环网柜部分停电工作,若进线柜线路侧有电,进线柜应设遮栏,悬挂“___”标示牌。
A. 止步,高压危险!
B. 禁止合闸,有人工作!
C. 禁止攀登、高压危险!
D. 从此进出
【单选题】
配电站的变压器室内工作,人体与10kV高压设备带电部分应保持___ m安全距离。
A. 0.7
B. 1.0
C. 1.5
D. 3.0
推荐试题
【单选题】
A new vApp was built and tested in the corporate headquarters datacenter running vSphere 6.x. What condition would explain why the virtual machine is failing to boot in an offsite datacenter running on vSphere 5.5?___
A. The virtual machine was built with the default hardware version.
B. The VMFS 5 datastore is not compatible with virtual machines configured with vSphere 6.x.
C. a
D. RS 5.5 cluster cannot run virtual machines configured with vSphere 6.x.
【单选题】
An administrator is evaluating whether to deploy vCenter Server on a Windows server or on a vCenter Server appliance. The administrator has the following requirements: <A web browser will be utilized to manage the vSphere environment.> <16 ESXi hosts will be deployed.> <Licenses must be shared with a vCenter Server at another site.> <An external Oracle 10g database server will be used to host the vCenter Server database.> Why will the administrator need to deploy vCenter Server on a Windows server?___
A. Linked Mode is a requirement for the solution.
B. Oracle 10g is a requirement for the solution.
C. The vSphere web client is a requirement for the solution.
D. Management of more than 5 hosts is a requirement for the solution.
【单选题】
What is a benefit of using VMware Data Protection ?___
A. Provides support for guest-level backups and restores of Microsoft SQL Servers, Exchange Servers, and Share Point Servers.
B. Provides support for advanced storage services including replication, encryption, deduplication, and compression.
C. Provides direct access to VDP configuration integrated into the vSphere Client.
D. Reduces disk space consumed by virtual machine data using deduplication.
【单选题】
An administrator enables vSphere High Availability (HA) on an existing cluster with a large number of hosts and virtual machines. The administrator notices that the setup of vSphere HA on some of the hosts is failing. What step, if taken, might resolve this issue?___
A. Increase the value of the config.vpxd.das.electionWaitTimeSec setting.
B. Set the value of vpxd.das.aamMemoryLimit to 256.
C. Set the value of the das.useDefaultIsolationAddress setting to False.
D. Increase the value of the das.iostatsinterval setting.
【单选题】
An ESXi 6.x host consists of 24 logical cores. Hyperthreading is enabled on the host. What is the maximum number of vCPUs that can be assigned to a virtual machine on this host?___
A. 24
B. 48
C. 64
D. 128
【单选题】
By default, each ESXi 6.x host is provisioned with a certificate from which root certificate authority?___
A. RedHat Certificate Authority
B. VMware Certificate Authority
C. DigiCert Certificate Authority
D. Verisign Certificate Authority
【单选题】
An administrator is adding an NFS datastore as shown in the Exhibit. What is the purpose of the Servers to be added list?___
A. It contains the IP addresses of the NFS Storage Server to provide multipathing capability.
B. It contains the IP addresses of the ESXi hosts that mount the datastore.
C. It contains the IP addresses used for
D. ynamic Discovery of targets.
【单选题】
An administrator reports that the System Event log data is only available for 24 hours when reviewing the Hardware Status tab. Which condition could be responsible for the loss of data?___
A. A Reset event log was executed.
B. The statistical collection level was set to a value of 1.
C. The boot disk of the host is corrupt.
D. Syslog has been configured at the vCenter Server level.
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
【单选题】
An administrator is installing Windows into a virtual machine. The DVD has been mounted on the Host and configured for the virtual machine as shown in the Exhibit. Based on the exhibit, when the virtual machine is booted, why would it attempt to search for a PXE server? ___
A. The CD/DVD device is not connected.
B. The ISO is in the incorrect storage location.
C. The OS minimum requirements have not been met.
D. The CD/DVD device is not set to Client Device.
【单选题】
What component must be installed prior to deploying a vCenter Server in vSphere 6.x? ___
A. vCenter Identity Services
B. Platform Services Controller
C. vCenter Single Sign-On
D. Client Integration Plug-In
欢迎使用我爱刷题
×
微信搜索我爱刷题小程序
温馨提示
×
请在电脑上登陆“www.woaishuati.com”使用