【单选题】
《塔里木油田钻井井控实施细则》规定:使用电动钻机时,远程控制台摆在钻台后方,距井口___m以远。
查看试卷,进入试卷练习
微信扫一扫,开始刷题
相关试题
【单选题】
《塔里木油田钻井井控实施细则》规定:“三高”油气井一般应由具备___级资质的队伍施工。
A. 国企
B. 民企
C. 甲级资质
D. 乙级及以上资质
【单选题】
《塔里木油田钻井井控实施细则》规定:井控设计中, 一般油气井井口间的距离应大于等于___m。
【单选题】
《塔里木油田钻井井控实施细则》规定:井控设计中,高压、含H2S油气井井口与其它任何井井口之间的距离应大于等于___m。
【单选题】
《塔里木油田钻井井控实施细则》规定:井控设计中,丛式井组之间的井口距离应大于等于___m。
【单选题】
《塔里木油田钻井井控实施细则》规定:平衡压力钻井时,泥浆密度以裸眼井段中的最高地层压力当量泥浆密度值为基准,另加一个安全附加值来确定泥浆密度油水井为___。
A. 0.05~0.10g/cm3
B. 0.07~0.15g/cm3
C. 0.02 g/cm3
D. 2.3 g/cm3、
【单选题】
《塔里木油田钻井井控实施细则》规定:含硫化氢井,测井队配备( )台便携式H2S监测仪、___套正压式呼吸器。
A. 2、2
B. 2、3
C. 6、5
D. 5、7
【单选题】
《塔里木油田钻井井控实施细则》规定:钻井井场应配备不少于___台防爆轴流风机。
【单选题】
《塔里木油田钻井井控实施细则》规定:预探井在安装防喷器之后储备重泥浆和加重材料,评价井和开发井在钻开油气层验收前___天储备重泥浆和加重材料。
【单选题】
《塔里木油田钻井井控实施细则》规定:预探井和评价井,储备比井浆密度高0.15g/cm3以上的重泥浆不低于( ),储备加重材料不低于___。
A. 40m3 、50吨
B. 50m3 、60吨
C. 60m3 、70吨
D. 80m3 、100吨
【单选题】
《塔里木油田钻井井控实施细则》规定:预探井和评价井,对于井浆密度在___g/cm3以上的要储备重泥浆()m3以上。
A. 1.10、120
B. 1.20、130
C. 1.30、140
D. 1.50、160
【单选题】
《塔里木油田钻井井控实施细则》规定:钻井工程设计中,设计合理的井身结构和套管层序,并满足以下井控要求表层套管下深应满足封固浅水层、疏松地层、砾石层、流沙层的要求,且套管鞋坐入稳固岩层深度应大于等于___m。固井水泥应自井底返至地面。
【单选题】
《塔里木油田钻井井控实施细则》规定:在起钻前应进行充分循环,循环时间不少于一个循环周,进出口钻井液密度差≤___g/cm3;下钻到底先循环排除后效,再进行其它钻井作业。
A. 0.01
B. 0.02
C. 0.03
D. 0.05
【单选题】
《塔里木油田钻井井控实施细则》规定:防喷演习的时间要求(从发出溢流报警信号,到关闭液动节流阀前的节2a平板阀的时间):钻进___分钟。
【单选题】
按照《塔里木油田钻井井控实施细则》的规定:录井队发现液面异常后,立即报告当班司钻,并在___内与泥浆工电话或对讲机完成核实,情况核实后再次报告当班司钻。
A. 3分钟
B. 5分钟
C. 8分钟
D. 10分钟
【单选题】
《塔里木油田钻井井控实施细则》规定:钻井队现场班组井控第一责任人是___。
A. 钻井队平台经理
B. 当班司钻
C. 当班泥浆工
D. 联机员
【单选题】
《塔里木油田钻井井控实施细则》规定:钻井队现场井控第一责任人是___。
A. 钻井队平台经理
B. 当班司钻
C. 当班泥浆工
D. 联机员
【单选题】
《塔里木油田钻井井控实施细则》规定:便携式H2S监测仪___校验一次。
【单选题】
《塔里木油田钻井井控实施细则》规定:从___起至完井,值班干部应在井场24小时值班。
A. 安装防喷器完开钻之日
B. 钻开油气层之日
C. 开始录井之日
D. 开钻之日
【单选题】
《塔里木油田钻井井控实施细则》规定:___是检查起下钻安全的有力手段(溢漏同层井除外),不满足起钻条件的,严禁起钻。
A. 向上级汇报
B. 循环观察
C. 加重
D. 短程起下钻
【单选题】
《塔里木油田钻井井控实施细则》规定:发现有H2S气体浓度<30mg/m3(20ppm)时立即___。
A. 启动声光报警器报警
B. 报告值班干部
C. 戴好正压式呼吸器D、撤离到上风方向的紧急集合点
【单选题】
《塔里木油田钻井井控实施细则》规定:开井信号为___。
A. 一声长鸣笛
B. 两声短鸣笛
C. 三声短鸣笛
D. 一声长鸣笛、一声短鸣笛
【单选题】
《塔里木油田钻井井控实施细则》规定:防喷演习的时间要求(从发出溢流报警信号,到关闭液动节流阀前的节2a平板阀的时间):空井___分钟。
【单选题】
《塔里木油田钻井井控实施细则》规定:H2S地区作业井相关人员必须进行相应的___。
A. 井控技术培训
B. 安全文化培训
C. H2S防护培训
D. 操作技能培训
【单选题】
《塔里木油田钻井井控实施细则》规定:含硫油气井在井场入口处应有挂牌提示,≥30mg/m3挂___牌。
【单选题】
《塔里木油田钻井井控实施细则》规定:固定式H2S监测仪___校验一次。
【单选题】
《塔里木油田钻井井控实施细则》规定:含硫化氢井,测井队配备___台便携式H2S监测仪、( )套正压式呼吸器。
A. 2、2
B. 2、3
C. 6、5
D. 5、6
【单选题】
《塔里木油田钻井井控实施细则》规定:含硫化氢井场,井场距井口___m以内的电器设备、电动工具、接线应符合防爆要求,所用电缆一般不得有中间接头,如确需接头连接时,应使用防爆接头。
【单选题】
《塔里木油田钻井井控实施细则》规定:在钻开油气水层后,下套管前应换装___,并试压合格。
A. 全封闸板芯子
B. 剪切闸板芯子
C. 套管闸板芯子
D. 变径闸板芯子
【单选题】
《塔里木油田钻井井控实施细则》规定:检修设备时,___严禁空井或钻具静止在裸眼井段进行检修。下钻到底应先循环排除后效,再进行其它钻井作业。
A. 钻头应起到或下到套管鞋处
B. 空井
C. 钻具静止在裸眼井段
D. 没有规定
【单选题】
《塔里木油田钻井井控实施细则》规定:钻开油气层前,现场地质人员提前___天以上、以书面形式向钻井队提出钻开油气层的地质预告。
【单选题】
《塔里木油田钻井井控实施细则》规定:油气井井口距民宅应≥___m。
【单选题】
《塔里木油田钻井井控实施细则》规定:远程控制台一般摆放在面对钻台的左侧、放喷管线的后方,距井口___m以远,与放喷管线有2m以上的距离。
【单选题】
《塔里木油田钻井井控实施细则》规定:地破压力试验最高当量密度为本井段设计所用最高钻井液密度附加___g/cm3,地破压力试验控制当量密度一般不超过2.30g/cm3。
A. 0.05
B. 0.1
C. 0.15
D. 0.2
【单选题】
《塔里木油田钻井井控实施细则》规定:在开发井实施欠平衡钻井时,现场至少储备___倍以上井筒容积、密度高于设计地层压力当量泥浆密度( )g/cm3以上的泥浆。
A. 1.0 ~1.5、0.2
B. 1.0 ~2.0、0.2
C. 1.0~2.0、0.3
D. 1.0~2.0、0.5
【单选题】
《塔里木油田钻井井控实施细则》规定:在探井实施欠平衡钻井时,现场至少储备___倍以上井筒容积、密度高于预计地层压力当量泥浆密度( )g/cm3以上的泥浆;现场应储备足够的加重材料和处理剂。
A. 1.0 ~1.5、0.2
B. 1.0 ~2.0、0.2
C. 1.0~2.0、0.3
D. 1.0~2.0、0.5
【单选题】
《塔里木油田钻井井控实施细则》规定:含硫化氢井,录井队配备()台便携式H2S监测仪、___套正压式呼吸器、5(固定探头)固定式H2S监测仪。
A. 2、2
B. 3、12
C. 5、12
D. 7、6
【单选题】
《塔里木油田钻井井控实施细则》规定:含硫油气井在井场入口处应有挂牌提示,≥15mg/m3且<30mg/m3(20ppm)挂___牌。
【单选题】
《塔里木油田钻井井控实施细则》规定:含硫油气井在井场入口处应有挂牌提示,H2S浓度<15mg/m3(10ppm)挂___牌。
【单选题】
《塔里木油田钻井井控实施细则》规定:H2S气体溢流后压井,优先采用___法将地层流体压回地层,再节流循环加重。
A. 司钻
B. 工程师
C. 压回
D. 等待加重
【单选题】
《塔里木油田钻井井控实施细则》规定:含H2S地区井的营房摆放应距井口___m以远,避开低洼处,并处于季节风的上风或侧风方向。
A. 200
B. 300
C. 500
D. 600
推荐试题
【多选题】
Which two actions are prerequisites to adding ESXi 6.x hosts to a vSphere Distributed Switch? (Choose two.)___
A. Verify that there is at least one Distributed Port Group on the Distributed Switch.
B. Verify that the Distributed Port Group have active uplinks configured in its teaming and failover policy.
C. Verify that the
D. istributed Switch has been configured with a Network Profile.
【多选题】
An organization has configured Distributed Power Management (DPM) on a vSphere 6 cluster. The organization wants to be alerted when an ESXi host has been powered down by DPM. Which two options represent the type and name of the alarm that would accomplish this? (Choose two.)___
A. DrsEnteringStandbyModeEvent
B. DrsEnteredStandbyModeEvent
C. Event-based
D. Condition-based
【多选题】
Which two allow for the disabling of Network Rollback operations? (Choose two.)___
A. Modifying the vpxd advanded configuration options and adding the config.vpxd.network.rollback key
B. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\vpxd.cfg file and adjusting the<rollback> xml tag
C. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\vpxd.cfg file and adjusting the <networkrollback> xml tag
D. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\firstboot\vpxd-service- spec.prop file and adjusting the <rollback> xml tag
【多选题】
An administrator is tasked with performing a vMotion migration of a virtual machine. The virtual machine is configured as follows: <vSphere Flash Read Cache (vFRC) enabled> <Is part of a Distributed Resource Cluster (DRS) Cluster> Which two statements are true? (Choose two.)___
A. Each ESXi host in the cluster supports multiple virtual flash resources.
B. Each ESXi host in the cluster supports one virtual flash resource.
C. DRS treats powered-on virtual machines with Flash Read Cache as having a preferred affinity to their current host and moves them only for mandatory reasons.
D. DRS treats powered-on virtual machines with Flash Read Cache as having a required affinity to their current host and does not move them.
【多选题】
An administrator is using the Host Failures to Tolerate Admission Control Policy for a vSphere High Availability ___ cluster. When configuring this setting on the cluster, the administrator sees this error message: <Insufficient resources to satisfy HA failover level on cluster > What are two likely causes for the error? (Choose two.)(AB)
A. The hosts in the cluster are disconnected.
B. A host in the cluster is displaying an HA error.
C.
D. istributed Resource Scheduler has not been configured on the cluster.
【多选题】
What are two ways to identify TCP/IP stack information? (Choose two.)___
A. Using the vSphere Web Client
B. Using esxcli network ip netstack
C. Using esxcfg-netstack
D. Using the vSphere Client
【多选题】
Which two actions are required when enabling vFlash Read Cache for a virtual machine's virtual disk? (Choose two.)___
A. A value in the Virtual Flash Read Cache text box must be entered.
B. A Flash Resource Pool for Cache size reservation must be entered.
C. The Device backing and the block size must be configured.
D. The
E. nable virtual flash host swap cache check box must be selected.
【多选题】
What two IT infrastructure components are virtualized by vSphere Essentials? (Choose two.)___
A. Networks
B. Applications
C. Storage
D. Management
【多选题】
When attempting to access a virtual machine, an administrator is unable to login using the vSphere credentials. What two options are probable causes of the authentication failure? (Choose two.)___
A. The vSphere credentials have not been granted permissions.
B. The vSphere credentials are granted read-only permissions.
C. The vSphere credentials are granted no-access permissions.
D. The vSphere credentials are not a member of the local administrator group.
【多选题】
An administrator is performing a scripted installation of ESXi 6.x. In which three locations does the script need to be? (Choose three.)___
A. PXE Server
B. HTTPS
C. FTP
D. NFS
E. VVOLs Datastore
【多选题】
In order for a company to meet regulatory requirements, all ESXi 6.x Hosts must be configured to direct logs to a syslog server. What are two ways ESXi hosts can configured for this action? (Choose two)___
A. Use the esxcli system syslog command.
B. Edit them in the ESXi host Advanced System Settings.
C. From the Syslog collector user interface of the Web Client.
D. Syslog logging is not available for
E. SXi Hosts.
【多选题】
Which three actions can be executed when an alarm is triggered? (Choose three.)___
A. Send an email.
B. Send an SNMP trap.
C. Run a script or command.
D. Run an Orchestrator workflow.
E. Send a trigger to syslog.
【多选题】
An administrator is attempting to power on a virtual machine, but is unable to do so. Which two reasons are probable causes of the failure? (Choose two.)___
A. Storage access to the virtual machine swap file has been lost.
B. One of the virtual machine VMDK files is locked.
C. Virtual machine is running CentOS 7.0 64-bit.
D. Virtual machine has Hyper-Threading enabled.
【多选题】
An administrator has configured a host profile so that ESXi 6.x hosts will point to the corporate NTP server for time synchronization. The NTP server is located at 10.0.30.213, but time has not been synchronized properly across the ESXi hosts. The administrator reviews Host Profile settings as shown in the Exhibit. Which two steps are required to resolve the issue? (Choose two.)___
A. Correct the NTP server IP address.
B. Check the host for host profile compliance.
C. Remediate the host based on the updated host profile.
D. Change the NTP server to the FQDN as IP Addresses are not supported.
【多选题】
An administrator is attempting to migrate a large Hadoop virtual machine using vMotion. The administrator notices a delay when the machine is quiesced. The Hadoop virtual machine is processing many transactions a second to an in-memory database. Which two actions would help reduce the amount of time needed to perform a vMotion on this virtual machine? (Choose two.)___
A. Use multiple NICs for the vMotion vmkernel port.
B. Use a 10Gbps Network card for the vMotion vmkernel port.
C. Add an additional management network to help transmit the data quicker.
D. Disable Fault Tolerance before performing the vMotion.
【多选题】
An administrator is installing a new network card in an ESXi 6.x host that is part of a vSphere cluster. When the host is placed into maintenance mode, the vSphere Web Client displays the progress bar at 2% for over 30 minutes. Which two are likely reasons for this occurrence? (Choose two.)___
A. Maintenance mode is unable to migrate all virtual machines from the host.
B. There is a large number of virtual machines that must be migrated from the host.
C. VMware High Availability is in the process of reconfiguring the cluster.
D. Each virtual machine on the
E. SXi host must be reconfigured to recognize the new adapter.
【多选题】
Which two events happen when Distributed Resource Scheduler (DRS) is disabled? (Choose two.)___
A. The cluster's resource pool heirarchy and affinity rules are re-established when DRS is turned back on.
B. The cluster's resource pool hierarchy and affinity rules are not re-established when DRS is turned back on.
C. The cluster's resource pools are removed from the cluster.
D. The cluster's resource pools are removed from the cluster and assigned to the hosts.
【多选题】
Which two networking connection types can be configured on a virtual switch? (Choose two.)___
A. Virtual machine portgroups
B. VMkernel services (such as NFS, iSCSI, or vMotion) to the physical network
C. Web services over the Management Network
D. NFS and FCoE storage services
【多选题】
An administrator creates a DRS cluster of eight ESXi 6.x hosts. There are 10 virtual machines balanced across the hosts. An attempt to place the first host into maintenance mode fails. What are two reasons that the host failed to enter maintenance mode? (Choose two.)___
A. The DRS cluster Automation Level is set to Partially Automated mode.
B. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Should run on hosts in group.
C. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Must run on hosts in group.
D. One of the virtual machines on the
E. SXi Host entering maintenance mode is configured with an individual Automation Level set to Partially Automated.
【多选题】
When modifying a vApp, which two vSphere entities can be added? (Choose two.)___
A. A resource pool
B. A network pool
C. A vApp
D. A folder
【多选题】
From which two locations in the inventory hierarchy can you deploy a virtual machine using a template? (Choose two.)___
A. Directly from the template.
B. From a compute resource.
C. From an existing virtual machine.
D. From a Datastore.
【多选题】
A company has decided to implement Virtual SAN within their vSphere 6.x environment. The Virtual SAN cluster will be composed of three ESXi 6.x hosts that are on the Virtual SAN Ready Node list. Each ESXi host includes: <Two SAS Controllers that support Passthrough Mode> < Four Solid State Drives (SSDs) 1TB in size each> <20 SAS Magnetic Disks (MDs) 1TB in size each> <The SSDs and MDs are evenly split between the two SAS controllers>. The company will pilot a Virtual SAN cluster utilizing VMware best practices while maximizing storage capacity. The Virtual SAN cluster will use Manual Mode. Which two Disk Group configurations would meet the stated configuration requirements? (Choose two.)___
A. 4 disk groups with 1 SSD and 5 MDs each
B. 2 disk groups with 1 SSD and 7 MDs each
C. 2 disk groups with 2 SSDs and 7 MDs each
D. 2 disk groups with 1 SSD and 10 MDs each
【多选题】
A physical Windows 2008 R2 Server is converted to a virtual machine using VMware vCenter Converter. Upon completion of the conversion and subsequent power on operation, the virtual machine fails to boot and the message below is observed in the Console of the virtual machine: <STOP 0x0000007B INACCESSIBLE_BOOT_DEVICE>. Which two potential issues may be causing this boot failure? (Choose two.)___
A. An incorrect SCSI controller was selected during conversion.
B. Incompatible software drivers were migrated into the virtual machine from the source machine.
C. The vmdk file backing the virtual machine was thick provisioned.
D. A snapshot was taken immediately after the conversion completed.
【多选题】
An administrator is configuring the Failover Order option on a vSphere Distributed Switch. Which two options should be used with IP-hash load balancing? (Choose two.)___
A. Active Uplinks
B. Standby Uplinks
C. Unused Uplinks
D. Override Failover Order
【多选题】
An administrator is configuring the Maximum Transmission Unit value on a vSphere Distributed Switch. Which two options are typical values for ESXi networking? (Choose two.)___
A. 1492
B. 1500
C. 9000
D. 9089
【多选题】
Which two configurable options apply to both virtual machine CPU and memory allocation? (Choose two.)___
A. Reservation
B. Shares
C. Resource Pool
D. Reserve All
【多选题】
When attempting to power on a Virtual Machine you observe the following error: <Cannot open the disk '/vmfs/volumes/volume/vm/vm-000002.vmdk' or one of the snapshot disks it depends on.> Which three actions will be the best solutions to address this problem? (Choose three.)___
A. Verify that the virtual machine's disk files are present.
B. Investigate the host and virtual machine log files.
C. Verify the vmdk descriptor files and if required, recreate them.
D. Delete the disk file preventing the power on operation.
E. Migrate or register the virtual machine to a different host.
【多选题】
An administrator has been tasked with enabling High Availability ___ on a cluster in a vSphere 6.x environment with default settings. The cluster configures properly and there are no errors. The next day when powering on a virtual machine, an error is presented: <Not Enough Failover Resources>. Which three scenarios are likely causes of this error message? (Choose three.)(CDE)
A. The default VM Monitoring Sensitivity is set too high.
B. There are not enough datastore heartbeat datastores configured by default.
C. The default slot size in the cluster is set too high.
D. There are virtual machines with large CPU reservations.
E. A host is in maintenance mode for a replacement of a failed Hard Drive.
【多选题】
vMotion can be performed between which three physical boundaries? (Choose three.)___
A. Between two vCenter Server Systems
B. Between two vSphere Distributed Virtual Switches
C. Between two vCenter Server Datacenter objects
D. Between two VMware NSX Layer 4 segments
E. Between two NFS datastores
【多选题】
An administrator configures vSphere Replication for a virtual machine and enables multiple point in time (PIT) instances under the recovery settings in the Configure Replication wizard. Which two statements are correct for vSphere Replication with multiple point in time instances enabled? (Choose two.)___
A. vSphere Replication retains a number of snapshot instances of the virtual machine on the target site based on the retention policy that you specify.
B. vSphere Replication uses the virtual machine's snapshot instances to define the target site Point in Time instance based on the retention policy that you specify.
C. vSphere Replication does not support virtual machines with snapshots.
D. vSphere Replication supports virtual machines with snapshots.
【多选题】
An administrator is virtualizing a physical application server and adding it to an existing multi-tiered vApp. The application license is currently tied to the physical NIC's MAC address, so the administrator needs to ensure the license will function properly in the virtual machine. Which two actions can the administrator take to satisfy this task? (Choose two.)___
A. Set the MAC address for the vNIC in the guest operating system.
B. Install the physical server's NIC into the ESXi host.
C. Configure the MAC address for the vNIC using the vSphere Web Client.
D. Assign the physical server NIC's MAC address in the vSphere Distributed Switch.
【多选题】
Which two Fibre Channel zoning options are supported with vSphere 6.x? (Choose two.)___
A. Single-Initiator
B. Single-Initiator-Single-Target
C. Multiple-Initiators-Single-Target
D. Multiple-Initiators-Multiple-Targets
【多选题】
An administrator is attempting to remove an ESXi 6.x host from a vSphere Distributed Switch (vDS). When the administrator attempts to remove the host, the following error is observed: <The resource '16' is still in use.> What three steps are needed to successfully remove the host from the switch? (Choose three.)___
A. Select Manage Ports on the vDS for the host.
B. Locate all ports currently in use on the vDS for the host.
C. Migrate or delete any vmkernel or virtual machine adapters associated with the switch.
D. Remove all network cards from the switch before trying to remove the host.
E. Create a standard switch for everything to be automatically be migrated to.
【多选题】
Which two Virtual SAN related actions might start resynchronization of virtual machine objects? (Choose two.)___
A. Editing a virtual machine storage policy to increase the number of replicas.
B. Editing a virtual machine storage policy to reduce the number of replicas.
C. Editing a virtual machine storage policy to increase the number of disk stripes.
D. Editing a virtual machine storage policy to reduce the number of disk stripes.
【多选题】
An administrator is troubleshooting basic network connectivity issues. Which two scenarios are potential issues that this administrator might face? (Choose two.)___
A. The vSwitch is not attached to the correct physical network.
B. The portgroup is not configured to use correct VLAN.
C. Traffic shaping is configured incorrectly.
D. Jumbo frames is configured incorrectly.
【多选题】
Which three items should be validated prior to installing ESXi 6.x? (Choose three.)___
A. Remote Storage has been disconnected.
B. Installation media is available.
C. Server hardware clock is set to UTC.
D. Storage has been partitioned with a VMFS volume.
E. Network cards have been setup to use Jumbo
F. rames.
【多选题】
An administrator is performing an interactive installation of ESXi 6.x. Which three options are available for installation? (Choose three.)___
A. DVD
B. USB
C. PXE
D. Scripted
E. Auto Deploy
【多选题】
After installation of a host in your test environment, you need to move it to production. The only major change that needs to be made is that the hostname of the server needs to change. What are two ways that an administrator can change the host name without editing configuration files on the host directly? (Choose two.)___
A. Login to the Direct Console User Interface and change it from here.
B. Edit the Default TCP/IP Configuration from the vSphere Web Client.
C. Use the Ruby vSphere Client to send a script to the ESXi host that updates the hostname.
D. Update the information in DNS and the
E. SXi host will automatically update with these changes.
【多选题】
An administrator has unsuccessfully attempted several times to install an Operating System inside a virtual machine. The administrator finds that the installation fails at random intervals. Which two actions can be taken to resolve this issue? (Choose two.)___
A. Verify the md5sum and if invalid, download the installation files again.
B. Attempt the installation an additional time.
C. Attempt to use a different installation media or installation method.
D. Create a new virtual machine and attempt the installation with the existing media.
【多选题】
VMware tools is failing to install on a Microsoft Windows virtual machine. What are two possible situations that would prevent the installation? (Choose two.)___
A. The VMware tools installation media is corrupt.
B. The incorrect Operating System was selected in the virtual machine options.
C. The software prerequisites have not been installed.
D. The prerequisite services have not been started.