【单选题】
长期停用或新领用的电动工具应用绝缘电阻表测量其绝缘电阻，若带电部件与外壳之间的绝缘电阻值达不到( )MΩ，应禁止使用。
A. 1.0
B. 2.0
C. 3.0
D. 4.0
查看试卷，进入试卷练习
微信扫一扫，开始刷题
相关试题
【单选题】
在一般作业场所(包括金属构架上)，应使用Ⅱ类电动工具，是指( )。
A. 功率较小的工具
B. 充电工具
C. 带绝缘外壳的工具
D. 重量较重的工具
【单选题】
安全工器具使用前，应检查确认( )部分无裂纹、无老化、无绝缘层脱落、无严重伤痕等现象以及固定连接部分无松动、无锈蚀、无断裂等现象。
【单选题】
接地线的两端夹具应保证接地线与导体和接地装置都能接触良好、拆装方便，有足够的( )，并在大短路电流通过时不致松脱。
A. 机械强度
B. 耐压强度
C. 通流能力
D. 拉伸能力
【单选题】
绝缘隔板和绝缘罩只允许在( )kV及以下电压的电气设备上使用，并应有足够的绝缘和机械强度。
【单选题】
安全工器具宜存放在温度为( )、相对湿度为80%以下、干燥通风的安全工器具室内。
A. -10～+35℃
B. -10～+30℃
C. -15～+35℃
D. -15～+30℃
【单选题】
绝缘隔板和绝缘罩应存放在室内干燥、离地面( )mm以上的架上或专用的柜内。
A. 100.0
B. 150.0
C. 200.0
D. 300.0
【单选题】
电焊机的外壳应可靠接地，接地电阻不得大于( )Ω。
【单选题】
使用中的氧气瓶和乙炔气瓶应( )固定放置，氧气瓶和乙炔气瓶的距离不得小于5m，气瓶的放置地点不准靠近热源，应距明火lOm以外。
【单选题】
使用中的氧气瓶和乙炔气瓶应垂直固定放置，氧气瓶和乙炔气瓶的距离不得小于( )m；气瓶的放置地点不得靠近热源，应距明火( )m以外。
A. 4，8
B. 5，10
C. 5，8
D. 4，10
【单选题】
重大物件的起重、搬运工作应由( )负责，作业前应进行技术交底。
A. 工作负责人
B. 有经验的专人
C. 持证上岗人员
D. 工程技术人员
【单选题】
对在用起重设备，( )应进行一次常规性检查，并做好记录。
A. 每次使用前
B. 每半年
C. 每年
D. 每两年
【单选题】
起重设备、吊索具和其他起重工具的工作负荷，不得超过( )。
A. 额定标准
B. 铭牌规定
C. 规程要求
D. 公司标准
【单选题】
当风力达到( )级以上时，受风面积较大的物体不宜起吊。
【单选题】
起重吊钩应挂在物件的( )上。
A. 重心线
B. 中心线
C. 底部构件
D. 顶部构件
【单选题】
在起吊、牵引过程中，受力钢丝绳的周围、上下方、转向滑车( )、吊臂和起吊物的下面，禁止有人逗留和通过。
A. 前后方
B. 上下方
C. 内角侧
D. 外角侧
【单选题】
起重机停放或行驶时，其车轮、支腿或履带的前端或外侧与沟、坑边缘的距离不得小于沟、坑深度的( )倍；否则应采取防倾、防坍塌措施。
A. 1.2
B. 1.5
C. 1.8
D. 2
【单选题】
起重作业时，起重机臂架、吊具、辅具、钢丝绳及吊物等与110kV架空输电线路及其他带电体的距离不得小于( )m，且应设专人监护。
A. 2.0
B. 4.0
C. 5.0
D. 6.0
【单选题】
在带电设备区域内使用起重机等起重设备时，应安装接地线并可靠接地，接地线应用多股软铜线，其截面积不得小于( )mm2。
A. 25.0
B. 16.0
C. 10.0
D. 35.0
【单选题】
在带电设备区域内使用起重机等起重设备时，应( )，接地线应用多股软铜线，其截面积不得小于16mm2。
A. 安装接地线
B. 可靠接地
C. 安装接地线并可靠接地
D. 对角装设接地
【单选题】
凡在坠落高度基准面( )m及以上的高处进行的作业，都应视作高处作业。
【单选题】
高处作业应使用工具袋。上下传递材料、工器具应使用绳索；邻近带电线路作业的，应使用绝缘绳索传递，较大的工具应用绳拴在( )。
A. 牢固的构件上
B. 设备上
C. 设备外壳上
D. 横担上
【单选题】
高处作业区周围的孔洞、沟道等应设( )并有固定其位置的措施。
A. 盖板
B. 盖板、安全网
C. 盖板、安全网或遮栏（围栏）
D. 专人监护
【单选题】
高处作业，除有关人员外，他人不得在工作地点的下面通行或逗留，工作地点下面应( )
A. 有遮栏（围栏）或装设其他保护装置
B. 有遮栏
C. 有围栏
D. 装设其他保护装置
【单选题】
安全带和专作固定安全带的绳索在使用前应进行( )。安全带应按附录O定期检验，不合格的不得使用。
A. 全面检查
B. 质量检测
C. 外观检查
D. 应力试验
【单选题】
腰带和保险带、绳应有足够的机械强度，材质应耐磨，卡环(钩)应具有保险装置，操作应灵活。保险带、绳使用长度在( ) m以上的应加缓冲器。
【单选题】
在没有脚手架或者在没有栏杆的脚手架上高处工作，高度超过( ) m时，应使用安全带，或采取其他可靠的安全措施。
【单选题】
单梯的横档应嵌在支柱上，并在距梯顶( ) m处设限高标志。
A. 1
B. 1.2
C. 1.5
D. 1.8
【单选题】
使用单梯工作时，梯与地面的斜角度约为( )。
A. 60°
B. 40°
C. 30°
D. 45°
【单选题】
触电急救应分秒必争，一经明确心跳、呼吸停止的，立即就地迅速用( )进行抢救，并坚持不断地进行，同时及早与医疗急救中心(医疗部门)联系，争取医务人员接替救治。
A. 心脏按压法
B. 口对口呼吸法
C. 口对鼻呼吸法
D. 心肺复苏法
【单选题】
触电急救脱离电源，就是要把触电者接触的那一部分带电设备的( )断路器(开关)、隔离开关(刀闸)或其他断路设备断开；或设法将触电者与带电设备脱离开。
【单选题】
触电伤员脱离电源后，正确的抢救体位是( )。
A. 左侧卧位
B. 右侧卧位
C. 仰卧位
D. 俯卧位
【单选题】
触电急救，胸外心脏按压频率应保持在( )次/min。
A. 60
B. 80
C. 100
D. 120
【单选题】
犬咬伤后应立即用浓肥皂水或清水冲洗伤口至少( )min，同时用挤压法自上而下将残留伤口内唾液挤出，然后再用碘酒涂搽伤口。
【多选题】
为加强配电作业现场管理，规范各类工作人员的行为，保证( )安全，依据国家有关法律、法规，结合配电作业实际，制定本规程。
【多选题】
作业人员有权拒绝( )。
A. 强令冒险作业
B. 标准化作业
C. 规范作业
D. 违章指挥
【多选题】
在试验和推广( )的同时，应制定相应的安全措施，经本单位批准后执行。
A. 新技术
B. 新工艺
C. 新设备
D. 新材料
【多选题】
运用中的配电线路和设备，系指( )的配电线路和设备。
A. 全部带有电压
B. 一部分带有电压
C. 一经操作即带有电压
D. 已安装完毕
【多选题】
本规程适用于国家电网公司系统各单位所管理的运用中的( )及相关场所。
A. 配电线路、设备
B. 变电站内配电设备
C. 用户配电设备
D. 发电厂内低压配电设备
【多选题】
配电设备系指20kV及以下配电网中的配电站、开闭所(开关站，以下简称开闭所)、箱式变电站、柱上变压器、柱上开关(包括柱上断路器、柱上负荷开关)、环网单元、电缆分支箱、( )等。
A. 变电站内开关柜
B. 低压配电箱
C. 电表计量箱
D. 充电桩
【多选题】
作业人员应( )，经考试合格上岗。
A. 接受相应的安全生产知识教育和岗位技能培训
B. 掌握配电作业必备的电气知识
C. 掌握配电作业必备的业务技能
D. 并按工作性质，熟悉本规程的相关部分
推荐试题
【多选题】
Which two statements are true regarding VMware vSphere Flash Read Cache (vFRC)? (Choose two.)___
A. Cache fills and cache evictions happen in the granularity of a cache block size.
B. vFRC caches data from both read and write I/Os, but write I/Os are always serviced by the underlying storage.
C. vFRC caches data from both read and write I/Os, but write I/Os are always serviced by the underlying cache data.
D. Cache fills and cache evictions happen in the granularity of the disk block size.
【多选题】
What are two possible causes of Storage Distributed Resource Scheduler (SDRS) being disabled on one or more virtual machine disks in a datastore cluster? (Choose two.)___
A. The virtual machine has vSphere Fault Tolerance disabled.
B. The virtual machine is a template.
C. The virtual machine swap file is on a shared datastore.
D. The disk is a CD-ROM/ISO file.
【多选题】
An administrator attempts to install vCenter Single Sign-On Server. The installer returns an error message indicating that the installation failed. Prior to the installation, all setup prerequisites were met. The administrator has generated a vCenter Server Single Sign-On support bundle. Which two files should the administrator analyze to determine the cause of the failure? (Choose two.)___
A. Server\utils\logs\imsTrace.log
B. Server\utils\logs\install.txt
C. %TEMP%\utils\logs\vminst.log
D. %TEMP%\vminst.log
【多选题】
An administrator is unable to remove an ESXi 6.x host from a vSphere Distributed Switch. What are two likely reasons for this issue? (Choose two.)___
A. Vmkernel interfaces on the switch are still in use.
B. VM Network port group adapters are connected to different switch.
C. Physical NICs are migrated to different switch.
D. VM Network adapters are connected to this switch.
【多选题】
Which two Identity Sources are available to add for vCenter Single Sign-On authentication? (Choose two.)___
A. LocalOS
B. OpenLDAP
C. NIS as an LDAP Server
D. VCMSDS
【多选题】
What are three goals of resource management within a cluster? (Choose three.)___
A. To prevent virtual machines from monopolizing resources and to guarantee predictable service rates.
B. To exploit undercommitted resources and overcommit with graceful degradation.
C. To provide solutions to potential problems that you might encounter when using vCenter Server.
D. To control the relative importance of virtual machines and provide flexible dynamic partitioning.
E. To provide additional network administration capabilities.
【多选题】
Which three actions can be taken as a result of executing the vSphere Update Manager 6.x scan and remediation wizards? (Choose three.)___
A. Install and upgrade software in virtual machines.
B. Upgrade the firmware on ESXi host devices.
C. Upgrade and Patch ESXi hosts.
D. Install and update third-party software on hosts.
E. Upgrade virtual machine hardware.
【多选题】
Which two statements are true about deploying and using vSphere Replication? (Choose two.)___
A. ESXi hosts managed by a single vCenter Server instance require a connection between the two vSphere Replication appliances.
B. Sites managed by different vCenter Server instances require a connection between the two vSphere Replication appliances.
C. Sites managed by different vCenter Server instances require the use of Site Recovery Manager and a connection between the two vSphere Replication appliances.
D. ESXi hosts managed by a single vCenter Server instance require a single vSphere Replication appliance.
【多选题】
An administrator is attempting to power on a virtual machine, but the task is hanging at 95%. What three scenarios best explain why this problem is happening? (Choose three.)___
A. A virtual machine question is currently being posed to the administrator.
B. Another task for the virtual machine or other component is already in progress.
C. The VMware High Availability cluster has insufficient resources to guarantee failover.
D. The host has lost access to the storage device containing the virtual machine files.
E. The host is under resource contention and unable to power on the virtual machine.
【多选题】
Which three features are not supported when using Fault Tolerance in vSphere 6.x? (Choose three.)___
A. Virtual Volumes (VVOLS)
B. Storage vMotion
C. Virtual Machine Component Protection
D. vMotion
E. vSphere Distributed Switches
【多选题】
Which two storage controller configurations can be used with Virtual SAN? (Choose two.)___
A. SAS controllers in Passthrough mode
B. SAS controllers in RAID0 mode
C. SAS controllers in RAID1 mode
D. SAS controllers in RAID10 mode
【多选题】
Which three are requirements when using vMotion to move a virtual machine across vCenter Server systems? (Choose three.)___
A. Both vCenter Servers must be using Enhanced Linked Mode.
B. Both vCenter Servers must be in the same Single Sign-On Domain.
C. Time must be synchronized.
D. Duplicate VM MAC addresses must be configured.
E. Both vCenter Servers must have High Availability enabled on source and destination clusters.
【多选题】
Which two components can be used when configuring Enhanced Linked Mode? (Choose two.)___
A. vCenter Server Appliance
B. vRealize Operations Manager
C. vSphere Management Appliance
D. vCenter Server for Windows
【多选题】
An organization has a number of virtual machines that would benefit from Fault Tolerance. These include: <A single vCPU Apache Server> < A dual vCPU vCenter Server> < A quad vCPU SQL Server> <An eight vCPU Hadoop Server>. Which two virtual machines can be configured to use VMware Fault Tolerance? (Choose two.)___
A. Apache Server
B. vCenter Server
C. SQL Server
D. Hadoop Server
【多选题】
Which two badges are major badges in vRealize Operations? (Choose two.)___
A. Risk
B. Efficency
C. Workload
D. Faults
【多选题】
An administrator is deploying multiple Windows 2003 Virtual Machines from the same template. What two steps should be taken to avoid network conflicts? (Choose two.)___
A. Customize the guest operating system.
B. Install VMware Tools into the new virtual machines.
C. Copy the Microsoft Sysprep tools onto the vCenter Server system.
D. Ensure the e1000 vmnic is selected for each new virtual machine.
【多选题】
Which three conditions would prevent Storage I/O Control from being enabled on a group of datastores? (Choose three.)___
A. The datastores planned for the solution are used by different vSphere clusters.
B. A datastore planned for the solution is configured as a Raw Device Mapping file.
C. A datastore planned for the solution has three extents.
D. A datastore planned for the solution is configured as NFS.
E. The organization has an Enterprise license.
【多选题】
Which two actions are prerequisites to adding ESXi 6.x hosts to a vSphere Distributed Switch? (Choose two.)___
A. Verify that there is at least one Distributed Port Group on the Distributed Switch.
B. Verify that the Distributed Port Group have active uplinks configured in its teaming and failover policy.
C. Verify that the
D. istributed Switch has been configured with a Network Profile.
【多选题】
An organization has configured Distributed Power Management (DPM) on a vSphere 6 cluster. The organization wants to be alerted when an ESXi host has been powered down by DPM. Which two options represent the type and name of the alarm that would accomplish this? (Choose two.)___
A. DrsEnteringStandbyModeEvent
B. DrsEnteredStandbyModeEvent
C. Event-based
D. Condition-based
【多选题】
Which two allow for the disabling of Network Rollback operations? (Choose two.)___
A. Modifying the vpxd advanded configuration options and adding the config.vpxd.network.rollback key
B. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\vpxd.cfg file and adjusting the<rollback> xml tag
C. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\vpxd.cfg file and adjusting the <networkrollback> xml tag
D. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\firstboot\vpxd-service- spec.prop file and adjusting the <rollback> xml tag
【多选题】
An administrator is tasked with performing a vMotion migration of a virtual machine. The virtual machine is configured as follows: <vSphere Flash Read Cache (vFRC) enabled> <Is part of a Distributed Resource Cluster (DRS) Cluster> Which two statements are true? (Choose two.)___
A. Each ESXi host in the cluster supports multiple virtual flash resources.
B. Each ESXi host in the cluster supports one virtual flash resource.
C. DRS treats powered-on virtual machines with Flash Read Cache as having a preferred affinity to their current host and moves them only for mandatory reasons.
D. DRS treats powered-on virtual machines with Flash Read Cache as having a required affinity to their current host and does not move them.
【多选题】
An administrator is using the Host Failures to Tolerate Admission Control Policy for a vSphere High Availability ___ cluster. When configuring this setting on the cluster, the administrator sees this error message: <Insufficient resources to satisfy HA failover level on cluster > What are two likely causes for the error? (Choose two.)(AB)
A. The hosts in the cluster are disconnected.
B. A host in the cluster is displaying an HA error.
C.
D. istributed Resource Scheduler has not been configured on the cluster.
【多选题】
What are two ways to identify TCP/IP stack information? (Choose two.)___
A. Using the vSphere Web Client
B. Using esxcli network ip netstack
C. Using esxcfg-netstack
D. Using the vSphere Client
【多选题】
Which two actions are required when enabling vFlash Read Cache for a virtual machine's virtual disk? (Choose two.)___
A. A value in the Virtual Flash Read Cache text box must be entered.
B. A Flash Resource Pool for Cache size reservation must be entered.
C. The Device backing and the block size must be configured.
D. The
E. nable virtual flash host swap cache check box must be selected.
【多选题】
What two IT infrastructure components are virtualized by vSphere Essentials? (Choose two.)___
A. Networks
B. Applications
C. Storage
D. Management
【多选题】
When attempting to access a virtual machine, an administrator is unable to login using the vSphere credentials. What two options are probable causes of the authentication failure? (Choose two.)___
A. The vSphere credentials have not been granted permissions.
B. The vSphere credentials are granted read-only permissions.
C. The vSphere credentials are granted no-access permissions.
D. The vSphere credentials are not a member of the local administrator group.
【多选题】
An administrator is performing a scripted installation of ESXi 6.x. In which three locations does the script need to be? (Choose three.)___
A. PXE Server
B. HTTPS
C. FTP
D. NFS
E. VVOLs Datastore
【多选题】
In order for a company to meet regulatory requirements, all ESXi 6.x Hosts must be configured to direct logs to a syslog server. What are two ways ESXi hosts can configured for this action? (Choose two)___
A. Use the esxcli system syslog command.
B. Edit them in the ESXi host Advanced System Settings.
C. From the Syslog collector user interface of the Web Client.
D. Syslog logging is not available for
E. SXi Hosts.
【多选题】
Which three actions can be executed when an alarm is triggered? (Choose three.)___
A. Send an email.
B. Send an SNMP trap.
C. Run a script or command.
D. Run an Orchestrator workflow.
E. Send a trigger to syslog.
【多选题】
An administrator is attempting to power on a virtual machine, but is unable to do so. Which two reasons are probable causes of the failure? (Choose two.)___
A. Storage access to the virtual machine swap file has been lost.
B. One of the virtual machine VMDK files is locked.
C. Virtual machine is running CentOS 7.0 64-bit.
D. Virtual machine has Hyper-Threading enabled.
【多选题】
An administrator has configured a host profile so that ESXi 6.x hosts will point to the corporate NTP server for time synchronization. The NTP server is located at 10.0.30.213, but time has not been synchronized properly across the ESXi hosts. The administrator reviews Host Profile settings as shown in the Exhibit. Which two steps are required to resolve the issue? (Choose two.)___
A. Correct the NTP server IP address.
B. Check the host for host profile compliance.
C. Remediate the host based on the updated host profile.
D. Change the NTP server to the FQDN as IP Addresses are not supported.
【多选题】
An administrator is attempting to migrate a large Hadoop virtual machine using vMotion. The administrator notices a delay when the machine is quiesced. The Hadoop virtual machine is processing many transactions a second to an in-memory database. Which two actions would help reduce the amount of time needed to perform a vMotion on this virtual machine? (Choose two.)___
A. Use multiple NICs for the vMotion vmkernel port.
B. Use a 10Gbps Network card for the vMotion vmkernel port.
C. Add an additional management network to help transmit the data quicker.
D. Disable Fault Tolerance before performing the vMotion.
【多选题】
An administrator is installing a new network card in an ESXi 6.x host that is part of a vSphere cluster. When the host is placed into maintenance mode, the vSphere Web Client displays the progress bar at 2% for over 30 minutes. Which two are likely reasons for this occurrence? (Choose two.)___
A. Maintenance mode is unable to migrate all virtual machines from the host.
B. There is a large number of virtual machines that must be migrated from the host.
C. VMware High Availability is in the process of reconfiguring the cluster.
D. Each virtual machine on the
E. SXi host must be reconfigured to recognize the new adapter.
【多选题】
Which two events happen when Distributed Resource Scheduler (DRS) is disabled? (Choose two.)___
A. The cluster's resource pool heirarchy and affinity rules are re-established when DRS is turned back on.
B. The cluster's resource pool hierarchy and affinity rules are not re-established when DRS is turned back on.
C. The cluster's resource pools are removed from the cluster.
D. The cluster's resource pools are removed from the cluster and assigned to the hosts.
【多选题】
Which two networking connection types can be configured on a virtual switch? (Choose two.)___
A. Virtual machine portgroups
B. VMkernel services (such as NFS, iSCSI, or vMotion) to the physical network
C. Web services over the Management Network
D. NFS and FCoE storage services
【多选题】
An administrator creates a DRS cluster of eight ESXi 6.x hosts. There are 10 virtual machines balanced across the hosts. An attempt to place the first host into maintenance mode fails. What are two reasons that the host failed to enter maintenance mode? (Choose two.)___
A. The DRS cluster Automation Level is set to Partially Automated mode.
B. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Should run on hosts in group.
C. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Must run on hosts in group.
D. One of the virtual machines on the
E. SXi Host entering maintenance mode is configured with an individual Automation Level set to Partially Automated.
【多选题】
When modifying a vApp, which two vSphere entities can be added? (Choose two.)___
A. A resource pool
B. A network pool
C. A vApp
D. A folder
【多选题】
From which two locations in the inventory hierarchy can you deploy a virtual machine using a template? (Choose two.)___
A. Directly from the template.
B. From a compute resource.
C. From an existing virtual machine.
D. From a Datastore.
【多选题】
A company has decided to implement Virtual SAN within their vSphere 6.x environment. The Virtual SAN cluster will be composed of three ESXi 6.x hosts that are on the Virtual SAN Ready Node list. Each ESXi host includes: <Two SAS Controllers that support Passthrough Mode> < Four Solid State Drives (SSDs) 1TB in size each> <20 SAS Magnetic Disks (MDs) 1TB in size each> <The SSDs and MDs are evenly split between the two SAS controllers>. The company will pilot a Virtual SAN cluster utilizing VMware best practices while maximizing storage capacity. The Virtual SAN cluster will use Manual Mode. Which two Disk Group configurations would meet the stated configuration requirements? (Choose two.)___
A. 4 disk groups with 1 SSD and 5 MDs each
B. 2 disk groups with 1 SSD and 7 MDs each
C. 2 disk groups with 2 SSDs and 7 MDs each
D. 2 disk groups with 1 SSD and 10 MDs each
【多选题】
A physical Windows 2008 R2 Server is converted to a virtual machine using VMware vCenter Converter. Upon completion of the conversion and subsequent power on operation, the virtual machine fails to boot and the message below is observed in the Console of the virtual machine: <STOP 0x0000007B INACCESSIBLE_BOOT_DEVICE>. Which two potential issues may be causing this boot failure? (Choose two.)___
A. An incorrect SCSI controller was selected during conversion.
B. Incompatible software drivers were migrated into the virtual machine from the source machine.
C. The vmdk file backing the virtual machine was thick provisioned.
D. A snapshot was taken immediately after the conversion completed.
