相关试题
【多选题】
螺旋道钉锚固时的温度宜保持在___以上。
A. 0℃
B. 10℃
C. 15℃
D. 22.5℃
【多选题】
无缝线路旧钢轨应切割成不大于___的短轨，以便于运输。
A. 6m
B. 7m
C. 12.5m
D. 25m
【多选题】
50kg/m钢轨轨端至第一螺栓孔中心距离为___。
A. 66mm
B. 76mm
C. 140mm
D. 150mm
【多选题】
线路施工作业时，须在符合规定的___带领下进行施工。
A. 施工带班人员
B. 工班员工
C. 施工负责人
D. 施工联络人
【多选题】
更换夹板在来车前，最低限度上足___个螺栓。
【多选题】
为防止受电弓接触导线接触点落于工作面外，起道高度单股不得超过___。
A. 20mm
B. 30mm
C. 40mm
D. 50mm
【多选题】
为防止电力机车脱弓，在不侵入建筑接近限界的情况下，拨道作业时，线路一侧拨道量年度累计不得大于___。
A. 120mm
B. 130mm
C. 140mm
D. 150mm
【多选题】
调高垫板应垫在轨底与大胶垫之间，一般情况下，每处调高垫板不得超过___。
【多选题】
无缝线路是由许多根标准长度的钢轨焊接成为不小于___的长钢轨连续铺设的轨道线路。
A. 300m
B. 400m
C. 500m
D. 600m
【多选题】
温度应力式无缝线路伸缩区长度根据计算确定，一般为___。
A. 50-100m
B. 40-100m
C. 30-100m
D. 20-100m
【多选题】
定期放散温度应力式无缝线路根据当地轨温条件，把钢轨内部的温度应力每年调整放散___次。
A. 4～5
B. 3～4
C. 2～3
D. 1～2
【多选题】
滚筒放散法是先封锁线路，然后将钢轨扣件全部松开，拆除长轨条端部的接头夹板，在长轨条底部每隔___放置一滚筒。
A. 5-10m
B. 10-15m
C. 15-20m
D. 20-25m
【多选题】
为设置规定的线路标志和信号标志提供空间路肩宽度不得小于___。
A. 0.2m
B. 0.3m
C. 0.4m
D. 2m
【多选题】
路基设置中侧沟的深度和底宽均应不小于___。
A. 0.4m
B. 0.5m
C. 0.6m
D. 0.7m
【多选题】
路基设置中沟底纵向坡度应不小于___。
【多选题】
平台宽度根据路堑深度和地层性质等因素确定，一般为___。
A. 0.5~1.0m
B. 1~1.5m
C. 1.5~2m
D. 2~2.5m
【多选题】
普通排水沟，底宽一般为___，深度为（ ）。
A. 0.2m 0.4m
B. 0.4m 0.6m
C. 0.6m 0.8m
D. 0.8m 1m
【多选题】
城市轨道轨距采用国家标准，直线轨距为1435mm，曲线地段按___半径给予加宽。
A. 相同
B. 不同
C. 5000m
D. 6000m
【多选题】
线路轨向允许偏差应符合《铁路线路维修规则》的规定：直线方向目视顺直、无甩尾。用___弦测量矢度。
A. 30m
B. 20m
C. 10m
D. 5m
【多选题】
如有高低，应对直线地段两股钢轨的高低分别进行检查，检查时，先俯身目视不小于___处钢轨下颚线的高低平顺情况。
A. 10m
B. 20m
C. 30m
D. 40m
【多选题】
在日常检查时如高低是向上凸起者，应同时使用___厚垫块，将弦的两端垫起。
A. 30mm
B. 40mm
C. 50mm
D. 60mm
【多选题】
轨道在短距离范围内的轨面不平顺称之为___。
【多选题】
一般来说，整体道床路线，正常性的沉降，在局部范围，不可能___以上的偏差。
A. 20mm
B. 30mm
C. 40mm
D. 50mm
【多选题】
通过垫板作业完全能够得到解决，碎石道床线路，误差在___以上时，可以采取起道作业办法，但要考虑轨面的顺坡率。
A. 20mm
B. 30mm
C. 40mm
D. 50mm
【多选题】
当起道量超过___时，必须申报供电系统的接触网部门予以配合。
A. 20mm
B. 30mm
C. 40mm
D. 50mm
【多选题】
线路上实际存在___形式的钢轨水平误差
【多选题】
钢轨中心线与___之间的倾斜度称为轨底坡。
A. 竖线
B. 垂直线
C. 斜线
D. 边缘线
【多选题】
线路养护维修时，可根据光带___对轨底坡进行调整。
【多选题】
复曲线是由___不同半径组成的曲线。
A. 四个
B. 三个
C. 两个
D. 两个或两个以上
【多选题】
缓和曲线的最小长度为20m，主要是从___一节车辆的全轴距而确定的。
【多选题】
下列情况的水沟不用采取防止冲刷或渗漏的加固措施的是___。
A. 流速大，可能引起冲刷的地段
B. 路堑内易产生基床病害地段的侧沟
C. 水田地区的排水沟
D. 天沟或截水沟的培堤成沟地段
【多选题】
对于不宜采用植物防护的边坡，不可采用___方法防护。
A. 铺砌草皮
B. 抹面
C. 喷浆
D. 勾缝
【多选题】
路基滑坡的防治措施不包括___。
A. 消除泥的有害作用
B. 改变滑体重心位置，增强稳定因素
C. 修建支挡建筑物，防止滑动
D. 改善滑带土的性质，提高力学强度
【多选题】
路基病害的整治不包括___ 。
A. 清筛道床
B. 换水
C. 采用封闭层
D. 保温防冻
【多选题】
道砟陷坑最常见的不包括___。
A. 道砟锅
B. 道砟囊
C. 道砟窝
D. 道砟坑
【多选题】
根据隧道的断面形式分：有矩形、拱形、圆形、多圆形及椭圆形等多种，但其中最主要的是___两种。
A. 圆形隧道和矩形隧道
B. 圆形隧道和拱形隧道
C. 拱形隧道和矩形隧道
D. 圆形隧道和椭圆形隧道
【多选题】
路基的防护和加固，不包括___。
A. 坡面防护
B. 冲刷防护
C. 封闭防护
D. 防沙防雪设施
【多选题】
___是在天然地面上用土石填筑而成的路基。
A. 半路堑
B. 半路堤
C. 路堤
D. 路堑
推荐试题
【判断题】
若自准直仪上读数鼓轮每格角值分度值为1"，则其线值分度值可用0.05mm/m表示
【判断题】
所有的紫色酒精，在 1 米内不准点有明火，不准放在暖气片上
【判断题】
固定式装配适用于单件和小批量模具的装配，以及装配精度要求较高，需要调整的部位较多的装配
【判断题】
我国对企业发生的事故，坚持“四不放过”原则进行处理
【判断题】
在机械设备中，凸轮表面误差将会引起扭转振动
【单选题】
What happens to the status of users already logged into ESXi Shell when a vSphere administrator enables lockdown mode?___
A. Users remain logged in and can run commands, except to disable lockdown mode.
B. Users remain logged in and can run commands, including disabling lockdown mode.
C. Users are immediately logged out of ESXi Shell.
D. Users are logged out after a timeout specified by the vSphere administrator.
【单选题】
What is the effective vSphere licensing level during the 60 day evaluation period?___
A. vSphere Foundation Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
【单选题】
To comply with security requirements, an administrator with a vCenter Server Appliance needs to force logoff of the vSphere web client after 10 minutes of inactivity.What should the administrator do to meet the requirement?___
A. Edit: /var/lib/vmware/vsphere-client/webclient.properties, modify session.timeout=10
B. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=600
C. Edit: /var/lib/vmware/vsphere-client/webclient.properties modify session.timeout=600
D. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=10
【单选题】
An administrator enables High Availability (HA) on a Virtual SAN cluster.Which network is used for HA Network Heatbeat configuration?___
A. The Management network.
B. The vMotion network.
C. The Virtual SAN network.
D. The Provisioning Traffic network.
【单选题】
A user wants to monitor a business-critical virtual machine to ensure that it doesn't run out of resources. What metric could be monitored in vRealize Operations to address this concern?___
A. Time Remaining badge
B. Compliance badge
C. Reclaimable Waste badge
D. Density badge
【单选题】
An administrator has recently installed a new ESXi 6.x Host, and during the configuration notices sporadic network problems. To check whether the issue occurred sometime during the configuration, the administrator would like to reset the system.How can this be accomplished in the shortest amount of time?___
A. Run the ESXi installer again and reinstall the host.
B. Select the Reset System Configuration option from the vSphere Client when connected directly to the host.
C. From the
D. irect Console User Interface, select Reset System Configuration.
【单选题】
A vApp is running out of compute resources when overall activity is high within the resource pool. At other times, everything is fine.What should be done to resolve this issue?___
A. Increase the size of the resource pool Shares.
B. Set the vApp's CPU and Memory Reservation Type to Expandable.
C. Set the vApp's CPU and Memory Limit to Unlimited.
D. Create a new resource pool with the existing hardware configuration.
【单选题】
A virtual machine has been renamed and an administrator is unable to find files with the new virtual machine name in the datastore.What is the reason for this?___
A. The names of the files on the datastore do not change.
B. The names of the files on the datastore have been corrupted.
C. The virtual machine needs to be re-added to the inventory.
D. The Distributed Resource Scheduler moved the virtual machine to another host.
【单选题】
An administrator has configured network connectivity for a new virtual machine, as shown in the Exhibit.What will occur with the network traffic of this virtual machine when communicating externally from vSwitch1?___
A. The virtual machine will communicate on both uplinks
B. The virtual machine will only communicate on vmnic1
C. The virtual machine will only communicate on vmnic2
D. The virtual machine will fail to communicate externally
【单选题】
An administrator is unable to create the first group in a new vRealize Operations environment. What is the likely cause of the problem?___
A. There are no group types defined.
B. The group is not defined in SSO.
C. There are more than 32 group types defined.
D. The description for the group is not provided.
【单选题】
A new vApp was built and tested in the corporate headquarters datacenter running vSphere 6.x. What condition would explain why the virtual machine is failing to boot in an offsite datacenter running on vSphere 5.5?___
A. The virtual machine was built with the default hardware version.
B. The VMFS 5 datastore is not compatible with virtual machines configured with vSphere 6.x.
C. a
D. RS 5.5 cluster cannot run virtual machines configured with vSphere 6.x.
【单选题】
An administrator is evaluating whether to deploy vCenter Server on a Windows server or on a vCenter Server appliance. The administrator has the following requirements: <A web browser will be utilized to manage the vSphere environment.> <16 ESXi hosts will be deployed.> <Licenses must be shared with a vCenter Server at another site.> <An external Oracle 10g database server will be used to host the vCenter Server database.> Why will the administrator need to deploy vCenter Server on a Windows server?___
A. Linked Mode is a requirement for the solution.
B. Oracle 10g is a requirement for the solution.
C. The vSphere web client is a requirement for the solution.
D. Management of more than 5 hosts is a requirement for the solution.
【单选题】
What is a benefit of using VMware Data Protection ?___
A. Provides support for guest-level backups and restores of Microsoft SQL Servers, Exchange Servers, and Share Point Servers.
B. Provides support for advanced storage services including replication, encryption, deduplication, and compression.
C. Provides direct access to VDP configuration integrated into the vSphere Client.
D. Reduces disk space consumed by virtual machine data using deduplication.
【单选题】
An administrator enables vSphere High Availability (HA) on an existing cluster with a large number of hosts and virtual machines. The administrator notices that the setup of vSphere HA on some of the hosts is failing. What step, if taken, might resolve this issue?___
A. Increase the value of the config.vpxd.das.electionWaitTimeSec setting.
B. Set the value of vpxd.das.aamMemoryLimit to 256.
C. Set the value of the das.useDefaultIsolationAddress setting to False.
D. Increase the value of the das.iostatsinterval setting.
【单选题】
An ESXi 6.x host consists of 24 logical cores. Hyperthreading is enabled on the host. What is the maximum number of vCPUs that can be assigned to a virtual machine on this host?___
【单选题】
By default, each ESXi 6.x host is provisioned with a certificate from which root certificate authority?___
A. RedHat Certificate Authority
B. VMware Certificate Authority
C. DigiCert Certificate Authority
D. Verisign Certificate Authority
【单选题】
An administrator is adding an NFS datastore as shown in the Exhibit. What is the purpose of the Servers to be added list?___
A. It contains the IP addresses of the NFS Storage Server to provide multipathing capability.
B. It contains the IP addresses of the ESXi hosts that mount the datastore.
C. It contains the IP addresses used for
D. ynamic Discovery of targets.
【单选题】
An administrator reports that the System Event log data is only available for 24 hours when reviewing the Hardware Status tab. Which condition could be responsible for the loss of data?___
A. A Reset event log was executed.
B. The statistical collection level was set to a value of 1.
C. The boot disk of the host is corrupt.
D. Syslog has been configured at the vCenter Server level.
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
