相关试题
【单选题】
当中心母钟或传输通道出现故障时,二级母钟将____。
A. 停止工作,但各子钟仍能运行
B. 停止工作,且各子钟不能运行
C. 自身晶振,指挥子钟运行
D. 自身晶振,但无法指挥子钟运行
【单选题】
中心母钟与车站二级母钟通过中心中心母钟的____接口进行通信。
A. 一路10M/100M
B. 一路RS422
C. 两路10M/100M
D. 两路RS422
【单选题】
中心母钟能够显示____等时间信息。
A. 时、分、秒
B. 月、日、星期、时、分、秒
C. 年、月、日、星期、时、分、秒
D. 年、月、日、时、分、秒
【单选题】
中心母钟____调整自身时间,二级母钟____调整自身时间。
A. 可以,可以
B. 不可以,可以
C. 可以,不可以
D. 不可以,不可以
【单选题】
母钟通过____接口向其它子系统发送标准时间信号。
A. RS232及RS422
B. RS422及RS485
C. RS232及10M/100M
D. RS422及10M/100M
【单选题】
中心母钟通过标准的____接口接收标准时间接收单元发送的标准时间信号。
A. RS232
B. RS422
C. RS485
D. 10M/100M
【单选题】
控制中心的子钟通过____接口与母钟连接。
A. RS232
B. RS422
C. RS485
D. 10M/100M
【单选题】
车站/车辆段的子钟通过____接口与母钟连接。
A. RS232
B. RS422
C. RS485
D. 10M/100M
【单选题】
子钟的地址码应可在____处进行设置更改。
A. 中心母钟
B. 二级母钟
C. 时钟网管
D. 子钟
【单选题】
宁溧线的所有子钟均为____。
A. 模拟子钟
B. 塔钟
C. 单面数显式子钟
D. 双面数显式子钟
【单选题】
时钟系统最主要的功能是为____提供标准时间。
A. 乘客
B. 车站工作人员
C. 各系统
D. 没有实际价值
【单选题】
当二级母钟发生故障时,子钟可____。
A. 不可运行
B. 可脱网独立运行
C. 可直接通过中心母钟校时运行
D. 可直接通过标准时间信号校时运行
【单选题】
3英寸数显式子钟内开关电源规格是____。
A. 2个5V/2A
B. 1个5V/2A,1个15V/2A
C. 2个15V/2A
D. 1个5V/2A,1个24V/2A
【单选题】
子钟内部出来的3芯对接线为电源线,线缆的颜色定义为____。
A. 红色为火线,蓝色为零线,黄色为地线
B. 红色为零线,蓝色为火线,黄色为地线
C. 红色为地线,蓝色为零线,黄色为火线
D. 红色为火线,蓝色为地线,黄色为零线
【单选题】
子钟内部出来的4芯对接线为信号线,线缆的颜色定义为____。
A. 红色为T+,黄色为T-,绿色为R+,蓝色为R-
B. 红色为T-,黄色为T+,绿色为R+,蓝色为R-
C. 红色为T+,黄色为T-,绿色为R-,蓝色为R+
D. 红色为T-,黄色为T+,绿色为R-,蓝色为R+
【单选题】
中心母钟通过向其他系统发送校时信号,收发状况为:____。
A. 既发送又接收
B. 既不发送又不接收
C. 只接收而不发送
D. 只发送而不接收
【单选题】
二级母钟箱的插板从左至右依次为____。
A. 电源板,信号板,信号板,通信板
B. 通信板,信号板,信号板,电源板
C. 信号板,通信板,电源板,信号板
D. 信号板,电源板,通信板,信号板
【单选题】
中心母钟的主要功能不包括____。
A. 向二级母钟提供精确的标准时间信号
B. 向全线子钟提供精确的标准时间信号
C. 向其他系统提供精确的标准时间信号
D. 向网管设备提供时间及设备状态信息
【单选题】
各车站站厅站台设置的子钟为____。
A. 3寸子钟
B. 3寸带日历子钟
C. 8寸子钟
D. 10寸子钟
【单选题】
以下子钟中,不会出现在车站的是____。
A. 3寸子钟
B. 3寸带日历子钟
C. 8寸子钟
D. 10寸子钟
【单选题】
车辆段运转室、值班员室、停车列检库、联合检修库等场所设置的子钟为____。
A. 3寸子钟
B. 3寸带日历子钟
C. 8寸子钟
D. 10寸子钟
【单选题】
二级母钟的站址号可在____上修改。
A. 时钟网管
B. 中心母钟
C. 二级母钟
D. 不可修改
【单选题】
当子钟接收不到母钟信号时,子钟____。
A. 无变化
B. 时分秒开始闪烁
C. 秒位右上角出现断开标识
D. 秒点开始闪烁
【单选题】
下方显示的子钟型号,宁溧线不存在的是____。
A. YZD314
B. YZD318
C. YZD1014
D. YZS宁溧线014
【单选题】
宁溧线与CCTV系统接口是____。
A. RS232
B. RS422
C. RS485
D. 10M/100M
【单选题】
在宁溧线,以下说法错误的是____。
A. 时钟系统与集中告警系统的接口为RS422
B. 在二级母钟与中心母钟通信正常时,手动修改二级母钟时间后,二级母钟会自动同步中心母钟时间后恢复
C. 室外子钟进行防水处理,防护等级IP≥56;室内子钟不具有防水效果
D. 一级母钟通过分配放大产生多路RS422接口信号。可以提供秒级的标准时间信号
【单选题】
宁溧线各过渡段电子围栏设备取电自____。
A. 综合监控设备房
B. 通信设备房
C. 车控室
D. 现场取电
【单选题】
宁溧线云台枪机的输入电压为____。
A. AC12V
B. DC12V
C. AC24V
D. DC24V
【单选题】
宁溧线云台枪机的默认IP为____。
A. 192.168.0.100
B. 192.168.0.1
C. 192.168.1.100
D. 192.168.1.1
【单选题】
宁溧线室内半球采用____通讯。
A. RS232
B. RS422
C. RS485
D. 10/100M
【单选题】
宁溧线安防摄像机用光端机上插入的光纤接头型号是____。
【单选题】
当电子围栏发生打火时,首先应进行的操作是____。
A. 断开电子脉冲主机的空开
B. 联系分管技术员及厂家
C. 更换该段电线
D. 试触检查漏电情况
【单选题】
宁溧线脉冲电子围栏上有____根合金线。
【单选题】
宁溧线安防系统可以做到的事情包括____。
A. 触发电子围栏后直接联动公安报警
B. 监测入侵人员并释放电流攻击
C. 对监控范围内进行录像并保存一定时间内的录像
D. 识别摄像机拍摄的人员是否为公司员工
【单选题】
以下位置中没有安防设备的是____。
A. 车辆段
B. 空港新城江宁-柘塘
C. 中山湖-幸庄
D. 卧龙湖-溧水
【单选题】
宁溧线车载PIS中,以下不属于本专业维护的是____。
A. 车载PIS服务器
B. 车载扬声器
C. 车载摄像机
D. 车载硬盘存储
推荐试题
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
18.交流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
19.直流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
20.接触器的额定电压应不小于主电路的___。
A. 短路电压
B. 工作电压
C. 最大电压
D. 峰值电压
【单选题】
21.接触器的额定电流应不小于被控电路的___。
A. 额定电流
B. 负载电流
C. 最大电流
D. 峰值电流
【单选题】
22.对于___工作制的异步电动机,热继电器不能实现可靠的过载保护。
A. 轻载
B. 半载
C. 重复短时
D. 连续
【单选题】
23.对于△接法的异步电动机应选用___结构的热继电器。