【单选题】
钢丝绳端部用绳卡固定连接时,绳卡压板应在钢丝绳主要受力的一边,不准正反交叉设置;绳卡间距不应小于钢丝绳直径的( )倍。 ___
查看试卷,进入试卷练习
微信扫一扫,开始刷题
相关试题
【单选题】
插接的绳环绳或绳套,其插接长度应不小于钢丝绳直径的( )倍,且不得小于300mm。___
【单选题】
使用油压式千斤顶时,任何人不得站在安全栓的( )。___
【单选题】
油压式千斤顶的顶升高度不得超过限位标志线;螺旋式及齿条式千斤顶的顶升高度不得超过螺杆或齿条高度的( )___
A. 4/5
B. 5/6
C. 3/4
D. 6/7
【单选题】
链条葫芦的吊钩、链轮、倒卡等有变形时,以及链条直径磨损量达( )时,禁止使用。___
【单选题】
两台及两台以上链条葫芦起吊同一重物时,重物的重量应( )每台链条葫芦的允许起重量。___
A. 不小于
B. 不大于
C. 等于
D. 大于
【单选题】
纤维绳在潮湿状态下的允许荷重应减少一半,涂沥青的纤维绳应降低( )使用。一般纤维绳禁止在机械驱动的情况下使用。___
A. 10%
B. 20%
C. 18%
D. 15%
【单选题】
凡在坠落高度基准面( )及以上的高处进行的作业,都应视作高处作业。___
A. 0.7m
B. 1.0m
C. 1.5m
D. 2.0m
【单选题】
凡参加高处作业的人员,应( )进行一次体检。___
【单选题】
在没有脚手架或者在没有围栏的脚手架上工作,高度超过( )时,应使用安全带,或采取其他可靠的安全措施。___
A. 1.5m
B. 1.2m
C. 1.0m
D. 0.8m
【单选题】
安全带应定期检验,检验周期为( )。___
【单选题】
利用高空作业车、带电作业车、叉车、高处作业平台等进行高处作业时,高处作业平台应处于稳定状态,需要移动车辆时,作业平台上( ). ___
A. 载人不得超2人
B. 不得留有工具
C. 不得载物
D. 不得载人
【单选题】
硬质梯子的横档应嵌在支柱上,梯阶的距离不应大于( ),并在距梯顶1m处设限高标志。___
A. 40cm
B. 45cm
C. 50cm
D. 55cm
【单选题】
使用单梯工作时,梯子与地面的斜角度约为( )。___
A. 40°
B. 50°
C. 60°
D. 70°
【单选题】
紧急救护时,发现伤员意识不清、瞳孔扩大无反应、呼吸、心跳停止时,应立即在现场就地抢救,用( )支持呼吸和循环,对脑、心重要脏器供氧。___
A. 心脏按压法
B. 口对口呼吸法
C. 口对鼻呼吸法
D. 心肺复苏法
【单选题】
触电急救,在医务人员( )前,不得放弃现场抢救,更不能只根据没有呼吸或脉搏的表现,擅自判定伤员死亡,放弃抢救。___
A. 未到达
B. 未接替救治
C. 作出死亡诊断
D. 判断呼吸或脉搏表现
【单选题】
触电急救应分秒必争,一经明确心跳、呼吸停止的,立即就地迅速用( )进行抢救,并坚持不断地进行,同时及早与医疗急救中心(医疗部门)联系,争取医务人员接替救治。___
A. 心脏按压法
B. 口对口呼吸法
C. 口对鼻呼吸法
D. 心肺复苏法
【单选题】
触电急救脱离电源,就是要把触电者接触的那一部分带电设备的( )断路器(开关)、隔离开关(刀闸)或其他断路设备断开;或设法将触电者与带电设备脱离开。___
【单选题】
伤员脱离电源后,判断伤员有无意识应在( )以内完成。___
A. 5s
B. 10s
C. 30s
D. 60s
【单选题】
触电伤员脱离电源后,正确的抢救体位是( )。___
A. 左侧卧位
B. 右侧卧位
C. 仰卧位
D. 俯卧位
【单选题】
触电急救,当采用胸外心脏按压法进行急救时,伤员应仰卧于( )上。___
A. 柔软床垫
B. 硬板床或地
C. 担架
D. 弹簧床
【单选题】
触电急救,胸外心脏按压频率应保持在( )次/min。___
A. 60
B. 80
C. 100
D. 120
【单选题】
进行心肺复苏法时,如有担架搬运伤员,应该持续做心肺复苏,中断时间不超过( )s。___
【单选题】
被电击伤并经过心肺复苏抢救成功的电击伤员,都应让其充分休息,并在医务人员指导下进行不少于( )h的心脏监护。___
【单选题】
烧伤急救时,强酸或碱灼伤应迅速脱去被溅染衣物,现场立即用大量清水彻底冲洗,要彻底,然后用适当的药物给予中和;冲洗时间不少于( )min。___
【单选题】
犬咬伤后应立即用浓肥皂水或清水冲洗伤口至少( )min,同时用挤压法自上而下将残留伤口内唾液挤出,然后再用碘酒涂搽伤口。___
【判断题】
事故紧急抢修工作,指电气设备发生故障被迫紧急停止运行,需按计划恢复的抢修和排除故障的工作
【判断题】
新参加电气工作的人员、实习人员和临时参加劳动的人员(管理人员、非全日制用工等),应经过安全知识教育后,方可到现场单独工作
【判断题】
待用间隔的隔离开关(刀闸)操作手柄、网门可不加锁
【判断题】
高压设备上工作,在手车开关拉出后,应观察隔离挡板是否可靠封闭
【判断题】
在运行中若必须进行中性点接地点断开的工作时,应先建立有效的旁路接地才可进行断开工作
【判断题】
经本单位批准允许单独巡视高压设备的人员巡视高压设备时,如果确因工作需要,可临时移开或越过遮栏,事后应立即恢复
【判断题】
地震、台风、洪水、泥石流等灾害发生后,如需要对设备进行巡视时,应制定必要的安全措施,得到设备运维管理单位批准,可单人巡视,但巡视人员应与派出部门之间保持通信联络
【判断题】
单人值班的变电站或发电厂升压站操作时,运维人员应根据发令人用电话传达的操作指令进行,可不用操作票
【判断题】
在进行倒负荷或解、并列操作前后,检查相关电源运行及负荷分配情况,不必填入操作票内
【判断题】
高压电气设备都应安装完善的防误操作闭锁装置
【判断题】
倒闸操作的基本条件之一:有值班调控人员、运维负责人正式发布的指令,并使用经事先审核合格的操作票
推荐试题
【填空题】
46.天基武器系统主要指攻击对方航天器用的卫星和卫星平台,包括 ___ 、 ___和___ 等。
【填空题】
47.中国人民解放军海军成立于___年。
【填空题】
48.新概念武器主要有 ___ 、___、 ___ 、 ___ 、___ 等。
【填空题】
49.核武器具有____、冲击波、____ ___、核电磁脉冲和放射性沾染等五种杀伤破坏因素。
【填空题】
50.精确制导技术是指采用高技术直接命中概率超过___以上的武器。
【单选题】
What is an example of social engineering?___
A. gaining access to a computer by observing the user login credentials
B. gaining access to a build through an unguarded entrance
C. gaining access to a server by using a USB stick
D. gaining access to a server room by posing as local IT
【单选题】
Which type of Layer 2 attack enables the attacker to intercept traffic that is intended for one specific recipient?___
A. BPDU attack
B. DHCP starvation I LAB
C. MAC address spoofing
D. CAM table overflow
【单选题】
Which about nested policy maps in a zone-based firewall is true ?___
A. They are limited to two leve ls in a hierarchical policy
B. Parent policies are previously defined policies that are defined by using the service policy command
C. A child policy is a new policy that uses a pre-existing policy.
D. A child policy is a new that uses a pre-existing policy
【单选题】
In which configuration do you configure the ip ospf authentication key 1 command?___
A. routing process
B. interface
C. privileged
D. global
【单选题】
Which statement about command authorization and security contexts is true?___
A. If command authorization is configured, it must be enabled on all contexts.
B. The change to command invokes a new context session with the credentials of the currently
C. AAA settings are applied on a per-context basis
D. The enable. 15 user ang admins with chang to permission ha e dfferent command authorization levels pertontext
【单选题】
Which command do you enter to enable authentication for OSPF on an interface?___
A. router(config-if)#ip ospf message-digest-key 1 md5 CIS COPASS
B. router(config-if)#ip ospf authentication message-digest
C. router(config-if)#ip ospf authentication-key CISCOPASS
D. router(config-if)#area 0 authentication message-digest
【单选题】
What feature defines a campus area network?___
A. It has a single geographic location
B. It lacks external connectivity.
C. It has a limited number of segments.
D. It has limited or restricted Internet access
【单选题】
Which type of attack most commonly involves a direct attack on a network?___
A. :phishing
B. Trojan horse
C. denial of service
D. social engineering
【单选题】
What information does the key length provide in an encryption algorithm?___
A. the cipher block size
B. the hash bloc k size
C. the number of permutations
D. the packet size
【单选题】
How do you verify TaCACS+ connectivity to a device?___
A. You successfully log in to the device by using the local credentials
B. You connect via console port and receive the login prompt.
C. You connect to the device using SSH and receive the login prompt.
D. You successfully log in to the device by using ACS credentials
【单选题】
Which term best describes the concept of preventing the modification of data in transit and in storage?___
A. availability
B. confidentially
C. fidelity
D. integrity
【单选题】
Which loS command is used to define the authentication key for ntp?___
A. switch(config )#ntp authentication-key 1 mds Clcs
B. switch(config )#ntp authenticate
C. switch(config)#ntp trusted-key 1
D. switch(config)#ntp source 192.168.0.1
【单选题】
What is true about the cisco lOS Resilient Configuration feature ?___
A. The feature can be disabled through a remote session
B. There is additional space required to secure the primary cisco lOS image file.
C. The feature automatically detects image or configuration version mismatch.
D. Remote storage is used for securing files
【单选题】
When is the default deny all policy an exception in zone-based firewalls?___
A. when traffic terminates on the router via the self zone
B. when traffic traverses two interfaces in different zones
C. when traffic traverses two interfaces in the same zone
D. when traffic sources from the router via the self zone
【单选题】
.If an access port is assigned as an isolated port in a PVLAN, which network ports can it communicate with?___
A. promiscuous ports in the same PLVAN
B. isolated ports in the same PVLAN
C. all ports in the same PAVLAN at ILAR
D. all ports in the adjacent PVLAN
【单选题】
Which IPSEC mode is used to encypt traffic directly between a client and a server VPN endpoint?___
A. quick mode
B. transport mode
C. aggressive mode
D. tunnel mode
【单选题】
Which command do you enter to verify that a vpn connection is established between two endpoints and that the connection is passing traffic? ___
A. Firewall#sh crypto session
B. Firewall#debug crypto isakmp
C. Firewall#tsh crypto ipsec sa
D. Firewall#sh crypto isakmp sa
【单选题】
which type of Pvlan port allows communication from all port types?___
A. isolated
B. in -line
C. community
D. promiscuous
【单选题】
Which command do you enter to configure your firewall to conceal internal addresses?___
A. no ip directed-broadcast
B. no ip logging facility
C. no proxy-arp
D. no ip inspect audit-trial
E. no ip inspect
F. route
【单选题】
Which feature defines a campus area network? ___
A. It has a limited number of segments.
B. It has limited or restricted Internet access
C. It lacks ex1ternal connectivity.
D. It has a single geographic location
【单选题】
What technology can you use to provide data confidentiality data integrity and data origin authentication on your network?___
A. IPSec
B. Certificate Authority
C. IKE
D. Data
E. ncryption Standards
【单选题】
which standard is a hybrid protocol that uses oakley and skerne ke y exchanges is an ISAKMP framework?___
【单选题】
What is the actual los privilege level of User Exec mode?___
【单选题】
What is the effect of the asa command crypto isakmp nat-traversal?___
A. It opens port 500 only on the out side interface
B. It opens port 500 only on the inside interface
C. It opens port 4500 on all interfaces that are IPSec enabled
D. It opens port 4500 only on the out side interfac
【单选题】
Which Fire POWER preproce ssor engine is used to prevent SYN attacks?___
A. Inline normalization
B. IP Defragmentation
C. Ports can
D. etection
【单选题】
Which NAT type allows objects or groups to reference an IP address ?___
A. identity NAt
B. static NAT
C. dynamic
D. dynamic NAT
【单选题】
Which Auto NAT policies are processed first?___
A. Dynamic NAT with longest prefix
B. Dynamic NAT with shortest prefix
C. static NAT with longest prefix
D. static NAT with shortest prefix
【单选题】
Which feature allows a dynamic Pat pool to se lect the next address in the pat pool instead of the next port of an existing address?___
A. next IP
B. round robin
C. dynamic rotation
D. NAT address rotation
【单选题】
Which IPS detection method can you use to detect attacks that are based on the attackers IP address?___
A. anomally-based
B. policy-based
C. signature-based
D. reputation-based
【单选题】
Which type of encryption technology has the broadest platform support?___
A. software
B. middleware
C. file-level
D. hardware
【单选题】
Which type of address translation supports the initiation of comm unications bidirectionally ?___
A. multi-session PAT
B. dynamic NAT
C. dynamic PAT
D. static NAT
【单选题】
Which label is given to a person who uses existing computer scripts to hack into computers while lacking the expertise to write the own?___
A. script kiddy
B. white hat hacker
C. hacktivist
D. phreaker
【单选题】
What is the primary purpose of a defined rule in an IPS?___
A. to configure an event action that takes place when a signature is triggered
B. to define a set of actions that occur when a specific user logs in to the system
C. to configure an event action that is pre-defined by the system administrator
D. to detect internal attacks
【单选题】
Which option is the default valuce for the Diffie- Hell man group when configuring a site-to-site VPn on an asa device ?___
A. Group 1
B. Group 2
C. Group 5
D. Group 7