相关试题
【单选题】
汽轮机3000rpm定速后,各轴承振动不得超过___
A. 0.02mm
B. 0.03mm
C. 0.04mm
D. 0.05mm
【单选题】
汽轮机D修后启动,3000rpm定速后应进行的试验有___
A. 主汽门严密性试验
B. 调门严密性试验
C. 喷油试验
D. 主汽门活动性试验
【单选题】
汽轮机并网带负荷后,当凝结水质不合格时,机组负荷不得超过___
A. 10MW
B. 15MW
C. 20MW
D. 25MW
【单选题】
汽轮机停运过程中,机组负荷降至___时停运高加汽侧。
A. 30MW
B. 35MW
C. 40MW
D. 45MW
【单选题】
汽轮机停机过程中,当机组负荷降至___时,开启各抽汽管道疏水电动门。
A. 15MW
B. 20MW
C. 25MW
D. 30MW
【单选题】
我中心汽轮机全真空惰走时间为___
A. 30min
B. 35min
C. 40min
D. 45min
【单选题】
汽轮机停机后,当高压缸下部内壁温度达___可间断性盘车。
A. 200℃
B. 250℃
C. 300℃
D. 350℃
【单选题】
顶轴油泵入口压力低于___时,顶轴油泵无法启动或跳闸。
A. 0.2MPa
B. 0.02MPa
C. 0.2KPa
D. 0.02KPa
【单选题】
顶轴油泵安全阀整定值是___
A. 20.56MPa
B. 20.57MPa
C. 20.58MPa
D. 20.59MPa
【单选题】
EH油系统溢油阀动作值是___
A. 17±0.05MPa
B. 17±0.5MPa
C. 17±0.02MPa
D. 17±0.2MPa
【单选题】
当凝结水过滤器进出口差压达___时,凝结水过滤器自动解列。
A. ≥0.05MPa
B. ≥0.02MPa
C. ≥0.1MPa
D. ≥0.2MPa
【单选题】
当凝结水温度超过___时,凝结水过滤器自动解列。
A. 120℃
B. 80℃
C. 70℃
D. 50℃
【单选题】
当除氧器水位正常,水温___后,向给水泵通水;
A. >50℃
B. >60℃
C. >70℃
D. >80℃
【单选题】
高加投运时,应将加热器汽侧压力维持在___
A. 0.05-0.01MPa
B. 0.05-0.1MPa
C. 0.01-0.5MPa
D. 0.1-0.5MPa
【单选题】
当高加汽侧压力与除氧器压差___时,将高加输水切换至热井。
A. <0.5MPa
B. <0.3MPa
C. <0.2MPa
D. <0.1MPa
【单选题】
当发生___时,给水泵必须立即停运
A. 给水泵密封水压力低,机械密封处漏水;
B. 液力偶合器摆动;
C. 润滑油压力偏低;
D. 给水泵气化,出口压力、电流摆动或降低;
【单选题】
正常情况下,一个月内EH油箱油位下降值为___
A. ≯15mm
B. ≯18mm
C. ≯20mm
D. ≯25mm
【单选题】
在停机中,如果发现润滑油泵故障,应如何处理___
A. 破坏真空停机;
B. 不破坏真空停机;
C. 立即并网运行
D. 保持额定转速空负荷运行;
【单选题】
汽轮机在启动时,低速暖机已结束,润滑油泵故障,油压逐渐下降,应如何处理___
A. 破坏真空停机;
B. 不破坏真空停机;
C. 迅速提升汽轮机转速;
D. 迅速降低汽轮机转速;
【单选题】
在相同的负荷下,中间级压力升高或同样的进汽参数下负荷下降,汽轮机可能发生了___
A. 通流部分结垢;
B. 汽轮机叶片断裂;
C. 调门突然关闭;
D. 机组背压过高;
【单选题】
主蒸汽参数低,通流部分过负荷,可导致汽轮机___
A. 轴向位移增加;
B. 轴向位移减小;
C. 轴向动静间隙减小;
D. 机组背压过高;
【单选题】
汽轮机发生水冲击,转子惰走时间缩短,盘车4小时后___
A. 禁止再次启动;
B. 可以再次启动;
C. 请示总工决定;
D. 视机组偏心值而定;
【单选题】
汽轮机通流部分发生异音或瞬间发出清晰的金属冲击声,汽轮机可能发生了___
A. 动静部分发生摩擦;
B. 水冲击事故;
C. 叶片断裂事故;
D. 过负荷事故;
【单选题】
蒸汽品质不合格,汽轮机通流部分静叶严重结垢,可能导致汽轮机___
A. 高压缸胀差增大;
B. 轴向位移增加;
C. 机组效率增加;
D. 轴向间隙增加;
【单选题】
汽轮机升速中转速低于一级临界转速时,要求轴振超过___,应立即打闸停机。
A. 0.23mm;
B. 0.24mm;
C. 0.25mm;
D. 0.26mm;
【单选题】
汽轮机通过临界转速时的轴承振动超过___时,应立即打闸停机。
A. 0.1mm;
B. 0.15mm;
C. 0.2mm;
D. 0.25mm;
【单选题】
当周波低于___,联系值长,要求与系统解列,保厂用;
A. 45HZ;
B. 46HZ;
C. 47HZ;
D. 48HZ;
【单选题】
对流体的平衡和运动规律具有主要影响的是___。
A. 黏性;
B. 压缩性;
C. 膨胀性;
D. 表面张力。
【单选题】
汽轮机中常用的和重要的热力计算公式是___。
A. 理想气体的过程方程式;
B. 连续方程式;
C. 能量方程式;
D. 动量方程式。
【单选题】
汽轮机纯冲动级的最佳速比为___
A. 1/2;
B. 1/4;
C. 3/4;
D. 都不是。
【单选题】
汽轮机油循环倍率最合适的范围是___。
A. 2~3;
B. 8~10;
C. 10~15;
D. 15~20。
【单选题】
蒸汽对金属的放热系数与蒸汽的状态有很大的关系,其中___的放热系数最低。
A. 高压过热蒸汽;
B. 湿蒸汽;
C. 低压微过热蒸汽;
D. 饱和蒸汽。
【单选题】
金属材料在外力作用下出现塑性变形的应力称___。
A. 弹性极限;
B. 韧性极限;
C. 强度极限;
D. 屈服极限。
【单选题】
金属零件在交变热应力反复作用下遭到破坏的现象称___。
A. 热冲击;
B. 热脆性;
C. 热变形;
D. 热疲劳。
【单选题】
电网频率超出允许范围长时间运行,将使叶片产生___,可造成叶片折断。
A. 裂纹;
B. 松动;
C. 蠕变;
D. 振动。
【单选题】
超速试验时,汽轮机转子应力比额定转速下应力应增加约___的附加应力。
A. 20%;
B. 25%;
C. 30%;
D. 15%。
【单选题】
协调控制系统共有五种运行方式,其中负荷调节反应最快的方式是___。
A. 机炉独自控制方式;
B. 协调控制方式;
C. 汽轮机跟随锅炉方式;
D. 锅炉跟随汽轮机方式。
【单选题】
汽轮发电机组转子的振动情况可由___来描述。
A. 振幅、波形、相位;
B. 位移、位移速度、位移加速度;
C. 激振力性质、激振力频率、激振力强度;
D. 轴承稳定性、轴承刚度、轴瓦振动幅值。
【单选题】
当汽轮发电机组转轴发生动静摩擦时,___。
A. 振动的相位角是不变的;
B. 振动的相位角是变化的;
C. 振动的相位角有时变、有时不变;
D. 振动的相位角始终是负值。
【单选题】
中间再热机组在滑参数减负荷停机过程中,再热蒸汽温度下降有___现象。
A. 超前;
B. 滞后;
C. 相同;
D. 先超后滞。
推荐试题
【单选题】
What does the dh group refer to?___
A. length of key for hashing C
B. length of key for encryption
C. tunnel lifetime key
D. length of key for key exchange
E. length of key for authentication
【单选题】
Which path do you follow to enable aaa through the SDM ?___
A. Configure Tasks > AAA
B. Configure > Addition Authentication > AAA
C. Configure > AAA
D. Configure > Additional Tasks > AAA
E. Configure Authentication > AAA
【单选题】
which technology cloud be used on top of an MPLS VPN to add confidentiality ?___
A. IPsec
B. 3DES
C. AES
D. SSL
【单选题】
Which term is most closely aligned with the basic purpose of a SIEM solution? ___
A. Non-Repudiation
B. Accountability
C. Causality
D. Repudiation
【单选题】
You have just deployed SNMPv3 in your environment, Your manager asks you to make sure that our SNMP agents can only talk to the SNMP Manager. What would you configure on your SNMI agents to satisfy this request?___
A. A SNMP View containing the SNMP managers
B. Routing Filter with the SNMP managers in it applied outbound
C. A standard ACL containing the SNMP managers applied to the SNMP configuration
D. A SNMP Group containing the SNMP managers
【单选题】
Which feature prevents loops by moving a nontrunking port into an errdisable state when a BPDU is received on that port?___
A. BPDU filte
B. DHCP snooping
C. BPDU guard
D. Port Fast
【单选题】
Which command enables port security to use sticky MAC addresses on a switch?___
A. switchport port-security violation restrict
B. switchport port-security mac-address sticky
C. switchport port-security violation protect
D. switchport port-security
【单选题】
When you edit an IPS subsignature, what is the effect on the parent signature and the family of subsignatures?___
A. The change applies to the parent signature and the entire family of subsignatures
B. The change applies to the parent signature and the subsignature that you edit
C. The change applies only to subsignatures that are numbered sequentially after the subsignature that you edit
D. Other signatures are unaffected, the change applies only to the subsignature that you dit
【单选题】
Which type of mechanism does Cisco FirePOWER de ploy to protect ag detected moving across other networks?___
A. antivirus scanning
B. policy-based
C. reputation-based
D. signature-based
【单选题】
What action must you take on the ise to blacklist a wired device?___
A. Locate the switch through which the device is connected and push an a cl restricting all access by the device
B. Issue a CoA request for the de vice's mac address to each access switch in the network
C. Revoke the device's certificate so it is unable to authenticate to the network
D. Add the device's MAc address to a list of black listed devices
【单选题】
Which type of firewall can perform deep packet inspection?___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于