【单选题】
下列关于建筑施工现场办公、生活等临时设施的选址的叙述,哪项是不正确的?___。
A. 不能满足安全距离要求的,任何情况下都不能设置。
B. 应考虑与作业区相隔离,周边环境必须具有安全性,如不得设置在高压线下。
C. 不得设置在沟边、崖边、河流边、强风口处、高墙下。
D. 不得设置在滑坡、泥石流等灾害地质带上和山洪可能冲击到的区域。
查看试卷,进入试卷练习
微信扫一扫,开始刷题
相关试题
【单选题】
外电线路电压分别为1kV以下、1~10kV、35~110kV、154~220kV、330~500kV时,其最小安全操作距离应当分别为___m。
A. 4、6、8、10、15
B. 3、5、7、9、14
C. 4、6、8、10、12
D. 6、8、10、12、15
【单选题】
下列关于建筑施工现场食堂的叙述,不正确的一项是___。
A. 食堂应当选择在通风、干燥、清洁的位置,离厕所、垃圾站等场所等污染源25m以外
B. 食堂制作间灶台及其周边应贴瓷砖,瓷砖的高度不宜小于1.5m
C. 食堂应设置独立的制作间、储藏间
D. 食堂的燃气罐应单独设置存放间,存放间应通风良好并严禁存放其它物品
【单选题】
下列关于建筑施工现场厕所的叙述,哪项是不正确的?___。
A. 厕所蹲位数量应根据施工现场作业人员的人量设置,一般为1:25~1:30。
B. 应设置水冲式或移动式厕所,地面应硬化,墙面刷白,纱门纱窗齐全。
C. 有女职工时应分设男女厕所,蹲坑间宜设置隔板,隔板高度不宜低于0.9m。
D. 厕所应由市政派人,定期进行清扫、冲刷、消毒,防止蚊蝇孳生,化粪池应及时清掏。
【单选题】
施工现场应设“六牌两图”。“两图”是指:___。
A. 施工现场总平面图、建筑工程立面(或效果)图
B. 施工现场总平面图、建筑工程立体图
C. 施工现场安全标志平面图、建筑现场临电布置图
D. 施工现场排水平面图、施工现场安全标志平面图
【单选题】
施工现场应该设置“两栏一报”,即___。
A. 读报栏、宣传栏和墙报
B. 读报栏、宣传栏和黑板报
C. 悬挂栏、张贴栏和黑板报
D. 防护栏、隔离栏和简报
【单选题】
根据《安全色》规定,安全色分为红、黄、蓝、绿四种颜色,分别表示___。
A. 禁止、指令、警告和提示
B. 指令、禁止、警告和提示
C. 禁止、警告、指令和提示
D. 提示、禁止、警告和指令
【单选题】
根据《安全标志》(GB2894-96),安全标志“禁止抛物”、“当心扎脚”、“必须戴防尘口罩”分别属于___。
A. 警告标志、禁止标志、指令标志
B. 禁止标志、指令标志、警告标志
C. 禁止标志、指令标志、提示标志
D. 禁止标志、警告标志、指令标志
【单选题】
下列关于安全标志含义的叙述,不正确的是___。
A. 禁止标志,含义是不准或制止人们某种行为
B. 警告标志,含义是警告人们当心、小心、注意
C. 指令标志,含义是必须遵守
D. 提示标志,含义是提示人们不能去做
【单选题】
施工现场同一位置必须同时设置不同类型、多个安全标志牌时,应当按照___的排列设置。
A. 警告、禁止、指令、提示的顺序,先右后左,先上后下
B. 警告、禁止、指令、提示的顺序,先左后右,先上后下
C. 警告、禁止、指令、提示的顺序,先左后右,先下后上
D. 提示、指令、禁止、警告的顺序,先左后右,先上后下
【单选题】
下列关于施工现场设置塔机应注意的安全事项,不正确的是___。
A. 拟建的建筑物临近街道,塔轨应尽量布置在建筑物的内侧
B. 塔机与临近的高压线达不到安全距离时,应搭设防护架,并限制旋转的角度
C. 在一个现场内同时布置多台塔式起重机时,应保证交叉作业安全
D. 塔式起重机布置时应考虑避雷、消防要求
【单选题】
在建筑施工现场,砖应丁码成方垛,不得超高,距沟槽坑边不小于___。
A. 0.5m
B. 1.0m
C. 0.3m
D. 1.2m
【单选题】
下列对施工现场主要材料、半成品堆放的叙述,不正确的是___。
A. 大型工具,应当一头见齐。
B. 砂应堆成方,石子应当按不同粒径规格分别堆放成方。
C. 混凝土构件堆放场地应坚实、平整,按规格、型号堆放。
D. 各种模板应当按规格分类堆放整齐,地面应平整坚实,叠放高度一般不宜超高2.6m,大模板存放应放在经专门设计的存架上。
【单选题】
下列对施工现场的场地清理的叙述,不正确的是___。
A. 作业区及建筑物楼层内,要做到工完场地清
B. 各楼层清理的垃圾应当集中起来,定时运走
C. 施工现场的垃圾应分类集中堆放
D. 垃圾应当用器具装载清运,严禁高处抛撒
【单选题】
施工现场发生火灾时,应当拨打___向公安消防机构报警。
A. 110
B. 119
C. 120
D. 114
【单选题】
下列叙述中,不属于防治大气污染的是___。
A. 施工现场宜采取措施硬化,其中主要道路、料场、生活办公区域必须进行硬化处理,土方应集中堆放
B. 施工现场的强噪声设备宜设置在远离居民区的一侧
C. 集中堆放的土方和裸露的场地应采取覆盖、固化或绿化等措施
D. 使用密目式安全网对在建建筑物、构筑物进行封闭,防止施工过程扬尘
【单选题】
下列关于防治大气污染的措施中,哪项不具有针对性?___。
A. 施工现场应设置排水沟及沉淀池,现场废水不得直接排入市政污水管网和河流
B. 从事土方、渣土和施工垃圾运输应采用密闭式运输车辆或采取覆盖措施
C. 施工现场应根据风力和大气湿度的具体情况,进行土方回填、转运作业
D. 建筑物内施工垃圾的清运,应采用专用封闭式容器吊运或传送,严禁凌空抛撒
【单选题】
下列叙述中,哪项不属于防治水污染的措施?___。
A. 施工现场应设置排水沟及沉淀池,现场废水不得直接排入市政污水管网和河流
B. 现场存放的油料、化学溶剂等应设有专门的库房,地面应进行防渗漏处理
C. 食堂、盥洗室、淋浴间的下水管线应设置隔离网
D. 施工现场应设置密闭式垃圾站,施工、生活垃圾应分类存放,并及时清运出场
【单选题】
夜间施工,是指___期间的施工。
A. 10时至次日6时
B. 22时至次日6时
C. 晚22时至次日5时
D. 晚9时至次日6时
【单选题】
根据《建筑施工场界噪声限值》,在城市建城区内禁止夜间施工的设备是___。
A. 推土机、挖掘机、装载机等
B. 各种打桩机
C. 混凝土搅拌机、振捣棒、电锯等
D. 吊车、升降机等
【单选题】
下列关于省级安全文明工地的叙述,哪项是不正确的?___
A. 申报资料中包括市建筑施工安全监督机构推荐的检查评分资料
B. 复查验收小组应当听取受检工程项目部安全生产文明施工工作汇报
C. 施工单位可以直接向省建筑安全监督机构申报省级安全文明工地
D. 复查验收后,工程竣工验收质量不合格、发生四级以上安全生产事故的,将取消文明工地资格
【单选题】
建筑施工企业从事建筑施工活动前,应当向___申请领取安全生产许可证。
A. 国家安全生产监督局
B. 建设部
C. 省级及省级以上建设主管部门
D. 设区的市建设行政主管部门
【单选题】
对于隐瞒有关情况或者提供虚假材料申请安全生产许可证的,省建筑工程管理部门不予受理,该企业___之内不得再次申请安全生产许可证。
A. 1个月
B. 3个月
C. 6个月
D. 1年
【单选题】
建筑施工企业取得安全生产许可证后,应当加强日常安全生产管理,不得降低安全生产条件,并接受___的监督检查。
A. 安全生产综合监督管理部门
B. 省建筑工程管理部门
C. 县级以上人民政府建设(建筑)行政主管部门
D. 设区的市建设行政主管部门
【单选题】
《施工企业安全生产评价标准》(JGJ/T77-2003)自___起实施。
A. 2003年11月1日
B. 2003年12月1日
C. 2004年1月1日
D. 2004年2月1日
【单选题】
依据《施工企业安全生产评价标准》,施工企业安全生产评价的内容包括安全生产条件单项评价、安全生产业绩单项评价及由以上两项单项评价组合而成的___综合评价。
A. 安全生产管理工作
B. 安全生产管理水平
C. 安全生产管理目标
D. 安全生产能力
【单选题】
依据《施工企业安全生产评价标准》,安全生产条件、安全生产业绩单项评价和安全生产能力综合评价结果分为___等级。
A. 合格、不合格
B. 合格、基本合格、不合格
C. 优良、合格、不合格
D. 优良、合格、基本合格、不合格
【单选题】
省建筑业主管部门负责全省的建筑施工企业安全生产评价的___工作。
A. 指导、协调
B. 指导、监督
C. 指导、审查
D. 检查、核准
【多选题】
在生产过程中,下列哪些属于事故?___
A. 人员死亡
B. 人员重伤
C. 财产损失
D. 人员轻伤
E. 设备损失
【多选题】
事故隐患泛指生产系统中导致事故发生的___。
A. 人的不安全行为
B. 自然因素
C. 物的不安全状态
D. 客观因素
E. 管理上的缺陷
【多选题】
安全生产是是为了使生产过程在符合物质条件和工作程序下进行,防止发生人身伤亡、财产损失等事故,采取的___的一系列措施和活动。
A. 控制自然灾害的破坏
B. 保障人身安全和健康
C. 环境免遭破坏
D. 设备和设施免遭损坏
E. 消除或控制危险和有害因素
【多选题】
安全生产管理具体包括哪几方面的内容?___
A. 安全生产法制管理
B. 行政管理
C. 工艺技术管理
D. 设备设施管理
E. 作业环境和作业条件管理
【多选题】
安全生产法律法规包括安全生产方面的___
A. 国家标准
B. 行政法规
C. 行业规范
D. 规范性文件
E. 地方法规
【多选题】
下列哪些属于安全技术标准规范规程?___
A. 建筑施工高处作业安全技术规范JGJ80-91
B. 建设工程监理规范GB50319-2000
C. 建筑机械使用安全技术规程JGJ33-2001
D. 建筑施工安全检查标准JGJ59—99
E. 塔式起重机安全规程GB5144-94
【多选题】
安全生产规章制度是指___制定并颁布的安全生产方面的具体工作制度。
A. 国家
B. 行业主管部门
C. 地方政府
D. 企事业单位
E. 企业技术部门
【多选题】
从90年代起,建设部相继编写出台了多部建筑安全技术标准规范,其中包括___。
A. 建筑施工安全检查标准
B. 建筑工程施工许可管理办法
C. 建筑施工扣件式钢管脚手架安全技术规范
D. 龙门架及井架物料提升机安全技术规范
E. 建筑施工高处作业安全技术规范
【多选题】
《国务院关于加强安全生产工作的通知》(国发[1993]50号)确定的我国实行的安全生产管理体制是___。
A. 企业负责
B. 行业管理
C. 国家监察
D. 群众监督
E. 劳动者遵章守纪
【多选题】
《国务院关于进一步加强安全生产的决定》(国发[2004]2号)中指出:要努力构建___的安全生产工作格局。
A. 政府统一领导
B. 部门依法监管
C. 企业全面负责
D. 群众参与监督
E. 全社会广泛支持
【多选题】
按照建设部关于建筑施工企业安全生产管理机构设置的有关规定,下列那些属于安全生产管理机构的主要职责? ___
A. 落实国家有关安全生产法律法规和标准
B. 编制并适时更新安全生产管理制度
C. 组织开展全员安全教育培训
D. 组织开展安全检查
E. 组织编制专项施工方案
【多选题】
按照建设部关于建筑施工专职安全生产管理人员职责的有关规定,企业安全生产管理机构负责人应当履行下列哪些职责?___
A. 适时修订企业安全生产规章制度,
B. 调配各级安全生产管理人员
C. 进行建设工程项目的安全技术交底
D. 监督、指导并评价企业各部门或分支机构的安全生产管理工作
E. 配合有关部门进行事故的调查处理
【多选题】
按照建设部关于建筑施工专职安全生产管理人员职责的有关规定,企业安全生产管理机构工作人员应当履行下列哪些职责?___
A. 调配建设工程项目的安全生产管理人员
B. 负责安全生产相关数据统计
C. 安全防护和劳动保护用品配备及检查
D. 施工现场安全督查
E. 发现现场存在安全隐患时,及时向工程项目经理报告
推荐试题
【多选题】
Which two components can be used when configuring Enhanced Linked Mode? (Choose two.)___
A. vCenter Server Appliance
B. vRealize Operations Manager
C. vSphere Management Appliance
D. vCenter Server for Windows
【多选题】
An organization has a number of virtual machines that would benefit from Fault Tolerance. These include: <A single vCPU Apache Server> < A dual vCPU vCenter Server> < A quad vCPU SQL Server> <An eight vCPU Hadoop Server>. Which two virtual machines can be configured to use VMware Fault Tolerance? (Choose two.)___
A. Apache Server
B. vCenter Server
C. SQL Server
D. Hadoop Server
【多选题】
Which two badges are major badges in vRealize Operations? (Choose two.)___
A. Risk
B. Efficency
C. Workload
D. Faults
【多选题】
An administrator is deploying multiple Windows 2003 Virtual Machines from the same template. What two steps should be taken to avoid network conflicts? (Choose two.)___
A. Customize the guest operating system.
B. Install VMware Tools into the new virtual machines.
C. Copy the Microsoft Sysprep tools onto the vCenter Server system.
D. Ensure the e1000 vmnic is selected for each new virtual machine.
【多选题】
Which three conditions would prevent Storage I/O Control from being enabled on a group of datastores? (Choose three.)___
A. The datastores planned for the solution are used by different vSphere clusters.
B. A datastore planned for the solution is configured as a Raw Device Mapping file.
C. A datastore planned for the solution has three extents.
D. A datastore planned for the solution is configured as NFS.
E. The organization has an Enterprise license.
【多选题】
Which two actions are prerequisites to adding ESXi 6.x hosts to a vSphere Distributed Switch? (Choose two.)___
A. Verify that there is at least one Distributed Port Group on the Distributed Switch.
B. Verify that the Distributed Port Group have active uplinks configured in its teaming and failover policy.
C. Verify that the
D. istributed Switch has been configured with a Network Profile.
【多选题】
An organization has configured Distributed Power Management (DPM) on a vSphere 6 cluster. The organization wants to be alerted when an ESXi host has been powered down by DPM. Which two options represent the type and name of the alarm that would accomplish this? (Choose two.)___
A. DrsEnteringStandbyModeEvent
B. DrsEnteredStandbyModeEvent
C. Event-based
D. Condition-based
【多选题】
Which two allow for the disabling of Network Rollback operations? (Choose two.)___
A. Modifying the vpxd advanded configuration options and adding the config.vpxd.network.rollback key
B. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\vpxd.cfg file and adjusting the<rollback> xml tag
C. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\vpxd.cfg file and adjusting the <networkrollback> xml tag
D. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\firstboot\vpxd-service- spec.prop file and adjusting the <rollback> xml tag
【多选题】
An administrator is tasked with performing a vMotion migration of a virtual machine. The virtual machine is configured as follows: <vSphere Flash Read Cache (vFRC) enabled> <Is part of a Distributed Resource Cluster (DRS) Cluster> Which two statements are true? (Choose two.)___
A. Each ESXi host in the cluster supports multiple virtual flash resources.
B. Each ESXi host in the cluster supports one virtual flash resource.
C. DRS treats powered-on virtual machines with Flash Read Cache as having a preferred affinity to their current host and moves them only for mandatory reasons.
D. DRS treats powered-on virtual machines with Flash Read Cache as having a required affinity to their current host and does not move them.
【多选题】
An administrator is using the Host Failures to Tolerate Admission Control Policy for a vSphere High Availability ___ cluster. When configuring this setting on the cluster, the administrator sees this error message: <Insufficient resources to satisfy HA failover level on cluster > What are two likely causes for the error? (Choose two.)(AB)
A. The hosts in the cluster are disconnected.
B. A host in the cluster is displaying an HA error.
C.
D. istributed Resource Scheduler has not been configured on the cluster.
【多选题】
What are two ways to identify TCP/IP stack information? (Choose two.)___
A. Using the vSphere Web Client
B. Using esxcli network ip netstack
C. Using esxcfg-netstack
D. Using the vSphere Client
【多选题】
Which two actions are required when enabling vFlash Read Cache for a virtual machine's virtual disk? (Choose two.)___
A. A value in the Virtual Flash Read Cache text box must be entered.
B. A Flash Resource Pool for Cache size reservation must be entered.
C. The Device backing and the block size must be configured.
D. The
E. nable virtual flash host swap cache check box must be selected.
【多选题】
What two IT infrastructure components are virtualized by vSphere Essentials? (Choose two.)___
A. Networks
B. Applications
C. Storage
D. Management
【多选题】
When attempting to access a virtual machine, an administrator is unable to login using the vSphere credentials. What two options are probable causes of the authentication failure? (Choose two.)___
A. The vSphere credentials have not been granted permissions.
B. The vSphere credentials are granted read-only permissions.
C. The vSphere credentials are granted no-access permissions.
D. The vSphere credentials are not a member of the local administrator group.
【多选题】
An administrator is performing a scripted installation of ESXi 6.x. In which three locations does the script need to be? (Choose three.)___
A. PXE Server
B. HTTPS
C. FTP
D. NFS
E. VVOLs Datastore
【多选题】
In order for a company to meet regulatory requirements, all ESXi 6.x Hosts must be configured to direct logs to a syslog server. What are two ways ESXi hosts can configured for this action? (Choose two)___
A. Use the esxcli system syslog command.
B. Edit them in the ESXi host Advanced System Settings.
C. From the Syslog collector user interface of the Web Client.
D. Syslog logging is not available for
E. SXi Hosts.
【多选题】
Which three actions can be executed when an alarm is triggered? (Choose three.)___
A. Send an email.
B. Send an SNMP trap.
C. Run a script or command.
D. Run an Orchestrator workflow.
E. Send a trigger to syslog.
【多选题】
An administrator is attempting to power on a virtual machine, but is unable to do so. Which two reasons are probable causes of the failure? (Choose two.)___
A. Storage access to the virtual machine swap file has been lost.
B. One of the virtual machine VMDK files is locked.
C. Virtual machine is running CentOS 7.0 64-bit.
D. Virtual machine has Hyper-Threading enabled.
【多选题】
An administrator has configured a host profile so that ESXi 6.x hosts will point to the corporate NTP server for time synchronization. The NTP server is located at 10.0.30.213, but time has not been synchronized properly across the ESXi hosts. The administrator reviews Host Profile settings as shown in the Exhibit. Which two steps are required to resolve the issue? (Choose two.)___
A. Correct the NTP server IP address.
B. Check the host for host profile compliance.
C. Remediate the host based on the updated host profile.
D. Change the NTP server to the FQDN as IP Addresses are not supported.
【多选题】
An administrator is attempting to migrate a large Hadoop virtual machine using vMotion. The administrator notices a delay when the machine is quiesced. The Hadoop virtual machine is processing many transactions a second to an in-memory database. Which two actions would help reduce the amount of time needed to perform a vMotion on this virtual machine? (Choose two.)___
A. Use multiple NICs for the vMotion vmkernel port.
B. Use a 10Gbps Network card for the vMotion vmkernel port.
C. Add an additional management network to help transmit the data quicker.
D. Disable Fault Tolerance before performing the vMotion.
【多选题】
An administrator is installing a new network card in an ESXi 6.x host that is part of a vSphere cluster. When the host is placed into maintenance mode, the vSphere Web Client displays the progress bar at 2% for over 30 minutes. Which two are likely reasons for this occurrence? (Choose two.)___
A. Maintenance mode is unable to migrate all virtual machines from the host.
B. There is a large number of virtual machines that must be migrated from the host.
C. VMware High Availability is in the process of reconfiguring the cluster.
D. Each virtual machine on the
E. SXi host must be reconfigured to recognize the new adapter.
【多选题】
Which two events happen when Distributed Resource Scheduler (DRS) is disabled? (Choose two.)___
A. The cluster's resource pool heirarchy and affinity rules are re-established when DRS is turned back on.
B. The cluster's resource pool hierarchy and affinity rules are not re-established when DRS is turned back on.
C. The cluster's resource pools are removed from the cluster.
D. The cluster's resource pools are removed from the cluster and assigned to the hosts.
【多选题】
Which two networking connection types can be configured on a virtual switch? (Choose two.)___
A. Virtual machine portgroups
B. VMkernel services (such as NFS, iSCSI, or vMotion) to the physical network
C. Web services over the Management Network
D. NFS and FCoE storage services
【多选题】
An administrator creates a DRS cluster of eight ESXi 6.x hosts. There are 10 virtual machines balanced across the hosts. An attempt to place the first host into maintenance mode fails. What are two reasons that the host failed to enter maintenance mode? (Choose two.)___
A. The DRS cluster Automation Level is set to Partially Automated mode.
B. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Should run on hosts in group.
C. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Must run on hosts in group.
D. One of the virtual machines on the
E. SXi Host entering maintenance mode is configured with an individual Automation Level set to Partially Automated.
【多选题】
When modifying a vApp, which two vSphere entities can be added? (Choose two.)___
A. A resource pool
B. A network pool
C. A vApp
D. A folder
【多选题】
From which two locations in the inventory hierarchy can you deploy a virtual machine using a template? (Choose two.)___
A. Directly from the template.
B. From a compute resource.
C. From an existing virtual machine.
D. From a Datastore.
【多选题】
A company has decided to implement Virtual SAN within their vSphere 6.x environment. The Virtual SAN cluster will be composed of three ESXi 6.x hosts that are on the Virtual SAN Ready Node list. Each ESXi host includes: <Two SAS Controllers that support Passthrough Mode> < Four Solid State Drives (SSDs) 1TB in size each> <20 SAS Magnetic Disks (MDs) 1TB in size each> <The SSDs and MDs are evenly split between the two SAS controllers>. The company will pilot a Virtual SAN cluster utilizing VMware best practices while maximizing storage capacity. The Virtual SAN cluster will use Manual Mode. Which two Disk Group configurations would meet the stated configuration requirements? (Choose two.)___
A. 4 disk groups with 1 SSD and 5 MDs each
B. 2 disk groups with 1 SSD and 7 MDs each
C. 2 disk groups with 2 SSDs and 7 MDs each
D. 2 disk groups with 1 SSD and 10 MDs each
【多选题】
A physical Windows 2008 R2 Server is converted to a virtual machine using VMware vCenter Converter. Upon completion of the conversion and subsequent power on operation, the virtual machine fails to boot and the message below is observed in the Console of the virtual machine: <STOP 0x0000007B INACCESSIBLE_BOOT_DEVICE>. Which two potential issues may be causing this boot failure? (Choose two.)___
A. An incorrect SCSI controller was selected during conversion.
B. Incompatible software drivers were migrated into the virtual machine from the source machine.
C. The vmdk file backing the virtual machine was thick provisioned.
D. A snapshot was taken immediately after the conversion completed.
【多选题】
An administrator is configuring the Failover Order option on a vSphere Distributed Switch. Which two options should be used with IP-hash load balancing? (Choose two.)___
A. Active Uplinks
B. Standby Uplinks
C. Unused Uplinks
D. Override Failover Order
【多选题】
An administrator is configuring the Maximum Transmission Unit value on a vSphere Distributed Switch. Which two options are typical values for ESXi networking? (Choose two.)___
A. 1492
B. 1500
C. 9000
D. 9089
【多选题】
Which two configurable options apply to both virtual machine CPU and memory allocation? (Choose two.)___
A. Reservation
B. Shares
C. Resource Pool
D. Reserve All
【多选题】
When attempting to power on a Virtual Machine you observe the following error: <Cannot open the disk '/vmfs/volumes/volume/vm/vm-000002.vmdk' or one of the snapshot disks it depends on.> Which three actions will be the best solutions to address this problem? (Choose three.)___
A. Verify that the virtual machine's disk files are present.
B. Investigate the host and virtual machine log files.
C. Verify the vmdk descriptor files and if required, recreate them.
D. Delete the disk file preventing the power on operation.
E. Migrate or register the virtual machine to a different host.
【多选题】
An administrator has been tasked with enabling High Availability ___ on a cluster in a vSphere 6.x environment with default settings. The cluster configures properly and there are no errors. The next day when powering on a virtual machine, an error is presented: <Not Enough Failover Resources>. Which three scenarios are likely causes of this error message? (Choose three.)(CDE)
A. The default VM Monitoring Sensitivity is set too high.
B. There are not enough datastore heartbeat datastores configured by default.
C. The default slot size in the cluster is set too high.
D. There are virtual machines with large CPU reservations.
E. A host is in maintenance mode for a replacement of a failed Hard Drive.
【多选题】
vMotion can be performed between which three physical boundaries? (Choose three.)___
A. Between two vCenter Server Systems
B. Between two vSphere Distributed Virtual Switches
C. Between two vCenter Server Datacenter objects
D. Between two VMware NSX Layer 4 segments
E. Between two NFS datastores
【多选题】
An administrator configures vSphere Replication for a virtual machine and enables multiple point in time (PIT) instances under the recovery settings in the Configure Replication wizard. Which two statements are correct for vSphere Replication with multiple point in time instances enabled? (Choose two.)___
A. vSphere Replication retains a number of snapshot instances of the virtual machine on the target site based on the retention policy that you specify.
B. vSphere Replication uses the virtual machine's snapshot instances to define the target site Point in Time instance based on the retention policy that you specify.
C. vSphere Replication does not support virtual machines with snapshots.
D. vSphere Replication supports virtual machines with snapshots.
【多选题】
An administrator is virtualizing a physical application server and adding it to an existing multi-tiered vApp. The application license is currently tied to the physical NIC's MAC address, so the administrator needs to ensure the license will function properly in the virtual machine. Which two actions can the administrator take to satisfy this task? (Choose two.)___
A. Set the MAC address for the vNIC in the guest operating system.
B. Install the physical server's NIC into the ESXi host.
C. Configure the MAC address for the vNIC using the vSphere Web Client.
D. Assign the physical server NIC's MAC address in the vSphere Distributed Switch.
【多选题】
Which two Fibre Channel zoning options are supported with vSphere 6.x? (Choose two.)___
A. Single-Initiator
B. Single-Initiator-Single-Target
C. Multiple-Initiators-Single-Target
D. Multiple-Initiators-Multiple-Targets
【多选题】
An administrator is attempting to remove an ESXi 6.x host from a vSphere Distributed Switch (vDS). When the administrator attempts to remove the host, the following error is observed: <The resource '16' is still in use.> What three steps are needed to successfully remove the host from the switch? (Choose three.)___
A. Select Manage Ports on the vDS for the host.
B. Locate all ports currently in use on the vDS for the host.
C. Migrate or delete any vmkernel or virtual machine adapters associated with the switch.
D. Remove all network cards from the switch before trying to remove the host.
E. Create a standard switch for everything to be automatically be migrated to.
【多选题】
Which two Virtual SAN related actions might start resynchronization of virtual machine objects? (Choose two.)___
A. Editing a virtual machine storage policy to increase the number of replicas.
B. Editing a virtual machine storage policy to reduce the number of replicas.
C. Editing a virtual machine storage policy to increase the number of disk stripes.
D. Editing a virtual machine storage policy to reduce the number of disk stripes.
【多选题】
An administrator is troubleshooting basic network connectivity issues. Which two scenarios are potential issues that this administrator might face? (Choose two.)___
A. The vSwitch is not attached to the correct physical network.
B. The portgroup is not configured to use correct VLAN.
C. Traffic shaping is configured incorrectly.
D. Jumbo frames is configured incorrectly.