相关试题
【单选题】
压力表在下列哪情况下仍可使用。___
A. 指针不能回到零点
B. 指针跳动或表面漏气
C. 超过允许误差
D. 使用时间超过半年
【单选题】
某现场压力表指示数为0.5MPa,此仪表指示数值为___。
A. 绝对压力
B. 大气压力
C. 表压力
D. 真空度
【单选题】
下列属于化学变化的是___。
A. 传热
B. 蒸发
C. 铁锈的生成
D. 萃取
【单选题】
条件___是造成M401联锁停车的原因。
A. HS40101启动
B. PALL40004(R401压力超低)
C. R401压力PIC40002高报
D. R401温度TIC40001高报
【单选题】
引起LV50001阀门关的原因是___。
A. LAH50302
B. LAH50304
C. LAHH50302
【单选题】
干燥系统的K502启动时,通过调节___来调节出口压力。
A. 出口阀
B. 入口阀
C. 出口管线的回流阀
D. 无需调节
【单选题】
COD高说明水质___。
A. 被严重污染
B. 污染程度较轻
C. 污染程度不详
D. 不确定
【单选题】
特级、一级《用火作业许可证》有效时间不超过___小时。
【单选题】
使用气焊、气割动火作业时,乙炔瓶应___。
A. 卧放
B. 直立放置
C. 倾斜放置
D. 无要求
【单选题】
对受限空间内可燃或有毒气体进行测试的方法是___。
A. 将点燃的火柴扔进去
B. 将活的小动物放入
C. 取样或采用经标准气体样品标定合格的便携式分析仪分析
D. 用鼻子去闻
【单选题】
对于高处作业,下列说法错误的是___。
A. 作业人员应正确配戴符合GB6095要求的安全带
B. 带电高处作业应使用绝缘工具或穿均压服
C. 高处作业(30m以上)宜配备通讯联络工具
D. 拆除脚手架、防护棚时,上部和下部可同时施工
【单选题】
聚丙烯产品的冲击强度随着MFR的增大而___。
【单选题】
如果节流阀开度过大,则生产能力___。
A. 变大
B. 变小
C. 不受影响
D. 没关系
【单选题】
启动主机前要保证辅机运行状态,且辅机扭矩低于规定值,这是为了___
A. 保证筒体内有足够的物料.
B. 保证模孔充满物料
C. 保证筒体温度足够
D. 防止主机过载
【单选题】
添加剂加入量大对MI会有什么影响。___
【单选题】
挤压机螺杆轴的密封采用___。
A. 工厂风
B. 仪表风
C. 氮气
D. 物料熔融
【单选题】
挤压机导热油系统热油升温梯度一般是___℃
【单选题】
PA901系统自动状态下能实现___。
A. 同一个料仓进料和出料同时进行
B. 不同料仓的进料和自掺混同时进行
C. 同一个料仓进料和倒料同时进行
【单选题】
界区来的乙烯的压力是___。
A. 3.0MPa
B. 4.0Mpa
C. 2.6MPa
【单选题】
界区来的氢气的压力是___。
A. 2.9MPa
B. 3.5MPa
C. 2.6MPa
【单选题】
抗冲共聚物中,下面叙述正确的是___。
A. 聚乙烯含量最大
B. 聚丙烯含量最大
C. 乙丙橡胶含量最大
【单选题】
循环气压缩机K401吹扫气的作用是___。
A. 防止循环气中的粉末进入轴承
B. 防止循环气中的粉末进入密封
C. 防止循环气中的粉末进人气阀
D. 防止循环气中的粉末进入活塞
【单选题】
R401压力与料位关系正确的是___。
A. 料位减低则压力升高
B. 料位减低则压力减低
C. 料位升高则压力升高
【单选题】
在聚丙烯产品的灰份组成中,占比重最大的是___。
A. 添加剂
B. 催化剂
C. 挥发份
D. 杂质
【单选题】
界区来的丙烯的压力是___。
A. 3.0MPa
B. 2.5MPa
C. 4.0MPa
【单选题】
二级《动火作业许可证》有效时间不超过___天。
【单选题】
动火过程中,监护人确需离开现场时,监护人可做以下处理___。
A. 收回作业证,暂停动火
B. 指派作业人员进行监护
C. 交待安全须知后离开
D. 继续动火作业
【单选题】
提高混炼机混炼强度的方法有___。
A. 增加螺杆转速
B. 减少进料量
C. 减小螺杆速度
D. 增大进料量
【单选题】
一环管和二环管的温度TAHH20401、TAHH20501的连锁起跳温度是___。
【单选题】
控制器PID表示比例、积分、微分其中微分的作用是___。
【单选题】
经HV20401的冲洗丙烯来自___。
A. SR201A/B
B. 冲洗丙烯总线
C. P201冲洗丙烯线
D. P202冲洗丙烯线
【单选题】
等规聚丙烯___溶于沸腾正庚烷中。
A. 能
B. 不能
C. 可能能溶
D. 可能不溶
【单选题】
正常操作时,R200压力应比R201高:___。
A. 0.1MPa左右
B. 0.2MPa
C. 0.5MPa
D. 0.05MPa
【单选题】
当精馏塔处于___时,此时的回流比最大。
A. 全回流
B. 最小回流
C. 适宜回流
D. 正常回流
【多选题】
粉料输送风机联锁系统的主要作用是___
A. 保护机器免受机械损害
B. 防止风机入口真空操作和空气进入系统
C. 防止粉末输送线堵塞
D. 防止粉末料仓低料位
【多选题】
切粒机开车时扭矩过高的原因是___
A. 切刀刀口损坏或钝化
B. 开车前下料量设定过高导致模板上形成薄膜
C. 切刀液压设定过低
D. 切粒机转速过低
【多选题】
当需要较长时间停车时,挤出机机体温度和加工段温度应当降低,这是为了___
A. 防止高温烫伤
B. 避免物料降解、碳化
C. 节能
D. 防止模板变形
【多选题】
在HV10306打开向D106加催化剂时不能打开的阀是___。
A. HV10302
B. HV10303
C. HV10304
D. HV10305
【多选题】
R201温度上升过快时,要做以下调整___。
A. 加大丙烯量
B. 降低夹套水加热量
C. 降低催化剂冲程或停止催化剂加入
D. 温度无法控制时加入2﹪CO。
推荐试题
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
【单选题】
An administrator is installing Windows into a virtual machine. The DVD has been mounted on the Host and configured for the virtual machine as shown in the Exhibit. Based on the exhibit, when the virtual machine is booted, why would it attempt to search for a PXE server? ___
A. The CD/DVD device is not connected.
B. The ISO is in the incorrect storage location.
C. The OS minimum requirements have not been met.
D. The CD/DVD device is not set to Client Device.
【单选题】
What component must be installed prior to deploying a vCenter Server in vSphere 6.x? ___
A. vCenter Identity Services
B. Platform Services Controller
C. vCenter Single Sign-On
D. Client Integration Plug-In
【单选题】
What is a valid plug-in status for a plug-in that has been added to a vSphere client? ___
A. Disabled
B. Unknown
C. Stopped
D. Installed
【单选题】
Users of an application are reporting performance issues. The following performance values are observed in the vSphere Web Client: <Host CPU utilization is 90%> <Virtual Machine memory utilization is consistently greater than 90% CPU Ready values are higher than 20%> What could be the cause of the application performance issue? ___
A. The host is lacking the CPU resources required to meet the demand.
B. The host is lacking the memory resources required to meet the demand.
C. The virtual machine is lacking the CPU resources required to meet the demand.
D. The virtual machine is lacking the memory resources required to meet the demand.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is re-provisioning an ESXi host and moving it to another datacenter. Which DCUI option should the administrator use to revert the system configuration to the default settings? ___
A. Reset System Configuration
B. Rebuild Default System Configuration
C. Revert System Configuration
D. Renew Default System Configuration
【单选题】
An administrator has just completed installing an ESXi 6.x host, but doesn't know what address has been configured. Where is the ESXi host IP address configured? ___
A. RVC console
B. Direct Console User Interface
C. vSphere Web Client
D. vSphere Client
【单选题】
When is it possible to place a VMFS5 datastore in maintenance mode? ___
A. When it is a member of a Storage DRS cluster
B. When it is a member of Virtual SAN cluster
C. When it is a member of a multi-extent datastore
D. When it is a member of a Virtual Volume
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Which Single Sign-On deployment mode should an administrator use for two 6.x vCenter Servers configured with linked mode? ___
A. Basic Single Sign-On with vCenter Server Heartbeat
B. Multisite Single Sign-On
C. Basic Single Sign-On
D. Single Sign-On with Linked Mode
【单选题】
What is required when changing a virtual machine name using the vSphere Web Client? ___
A. Verify connectivity to the ESXi host where the virtual machine is running and its inventory list is accessible.
B. Verify in which datastore the virtual machine resides and that you have access and its inventory list is accessible.
C. Verify that virtual machine files are stored in the same datastore and can be accessed in the datastore browser list.
D. Verify the virtual machine is not running in Fault Tolerant mode and that it is not in a Distributed Resource Scheduler cluster.
【单选题】
An administrator deploys vRealize Operations into a vSphere 6.x environment. After the deployment, the administrator notices that badges are not appearing. What is a likely cause of this behavior? ___
A. Badges do not appear until you register vRealize Operations with vCenter Server.
B. Badges do not appear until you register a vCenter Server in vRealize Operations.
C. The vRealize Operations appliance needs to be redeployed.
D. The vCenter Server appliance needs to be redeployed.
【单选题】
How are ports scaled on vSphere Standard Switches (vSS)? ___
A. Ports on a vSS can be dynamically scaled up and down.
B. Ports on a vSS can only be statically scaled up or down.
C. Ports on a vSS can only be dynamically scaled down.
D. Ports on a vSS can only be dynamically scaled up.
【单选题】
A High Availability (HA) cluster is configured to respond to a given number of host failures. The cluster contains virtual machines configured with these settings: VM1 has a 1GHz CPU reservation and no Memory reservation VM2 has a 2GHz CPU reservation and no Memory reservation VM3 has no CPU reservation and no Memory reservation . Given this information, what is the correct slot size for the cluster? ___
A. The CPU Reservation should be set to 32MHz and the memory reservation should be set to 32MB plus memory overhead.
B. The CPU reservation should be set to 1 GHz and the memory reservation should be set to 0MB plus memory overhead.
C. The CPU reservation should be set to 2 GHz, and the memory reservation should be set to 0MB plus the virtual machine memory overhead.
D. The CPU reservation should be set to 2 GHz, and the memory reservation should be set to 32MB, plus the virtual machine memory overhead.
【单选题】
An administrator is planning a vSphere infrastructure with the following specific networking requirements: <The ability to shape inbound (RX) traffic> <Support for Private VLANs (PVLANs)> <Support for LLDP (Link Layer Discovery Protocol)>. What is the minimum vSphere Edition that will support these requirements? ___
A. vSphere Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
【单选题】
When you add an ESXi 6.x host to a new Cluster, which vSphere object owns the CPU and Memory resources of the hosts? ___
A. vCenter Server
B. Datacenter
C. Cluster
D. Host
【单选题】
A user is trying to retrieve objects from a SharePoint server and finds the request is taking an excessive amount of time. An administrator tries to isolate the issue and notes the following: Application performance is poor when compared to virtual machines on other hosts. Performance improves when the virtual machine is moved to another host. The virtual machine encounters higher than expected CPU %Ready times. What conclusion can be reached regarding the performance issues for this virtual machine? ___
A. Host Power Management is directly impacting virtual machine performance.
B. The virtual machine has a large number of snapshots.
C. The Path Selection Policy for the storage device is set differently on the affected host.
D. Network I/O control is configured for the portgroup.
【单选题】
A virtual machine template is accidently removed from the vCenter Server Inventory. Which method would be used to recover the template back into the environment?___
A. Use the datastore browser to locate the template, then right click and add the .vmtx file to inventory.
B. Use the datastore browser to locate the template, then right click and add the .vmx file to inventory.
C. Using the Managed Object Browser and adding the template from the ManagedObjectReference:GuestFileManager object.
D. Using the Managed Object Browser and adding the template from the ManagedObjectReference:VirtualDiskManager object.
【单选题】
A vSphere administrator needs to backup a virtual machine that has a Microsoft SQL Server Database installed. Which solution allows for an application quiesce to occur during backup?___
A. VMware vCenter Converter
B. VMware vCenter Site Recovery Manager
C. VMware vSphere Replication
D. VMware vSphere Data Protection Advanced
【单选题】
An administrator is migrating a virtual machine from a Test cluster to a Production cluster. The two environments do not have any shared storage. What is the easiest way to accomplish this task? ___
A. Perform a Storage vMotion.
B. Perform a regular vMotion.
C. Perform a Virtual to Virtual migration.
D. Perform a backup and restore using VMware Data Protection.
【单选题】
An administrator must determine an appropriate backup solution, given these conditions: 50 of the virtual machines are in a resource pool named Finance. 50 of the virtual machines are in a resource pool named QA. Which solution allows an administrator the ability to backup 100 virtual machines? ___
A. Use Snapshot Manager on the vCenter Server to backup the virtual machines.
B. Use the VMware Consolidated Backup (vcb) tool on the ESXi Host to backup the virtual machines.
C. Use the VMware Data Recovery (VDR) Appliance on the vCenter Server to backup the virtual machines.
D. Use the VMware Data Protection (VDP) Appliance on one of the
E. SXi Hosts to backup the virtual machines.
【单选题】
What is a benefit of using Enhanced vMotion Compatibility for an environment? ___
A. EVC masks CPU features to allow compatibility between hosts that are dissimilar.
B. EVC allows for cross platform vMotion to occur.
C. EVC enables Long
D. istance vMotion.
【单选题】
How many Link Aggregation Groups (LAGs) can be configured on a vSphere 6.x Distributed Switch? ___
A. 64
B. 96
C. 128
D. 256
【单选题】
How many Link Aggregation Groups (LAGs) can be configured on a vSphere 6.x Distributed Switch? ___
A. 64
B. 96
C. 128
D. 256
【单选题】
An administrator needs to verify that vMotion operations can be performed in a vSphere data center.What round trip time (RTT) latency is the maximum value that will allow vMotion operations to succeed? ___
A. 50ms RTT
B. 100ms RTT
C. 150ms RTT
D. 200ms RTT