【单选题】
TGF23系列逆变器的额定电压为_______。___
A. 三相交流380×[1±5%]V
B. 单相交流220×[1±5%]V
C. 直流600V
D. A、B两种
查看试卷,进入试卷练习
微信扫一扫,开始刷题
相关试题
【单选题】
25T型客车充电器由DC110V充电机和_______组成。___
A. 单相逆变器
B. 三相逆变器
C. 蓄电池
D. 应急电源
【单选题】
25T型客车充电机的作用是将DC600V[AC380V]的输入变换成_______,供给客车照明、110V蓄电池充电及其他110V负载。___
A. DC220V
B. DC110V
C. AC220V
D. DC48V
【单选题】
60W/220V的交流白炽灯串联二极管后,接入220V交流电源,其消耗的电功率为_______。___
A. 60W
B. 30W
C. 15W
D. 7.5W
【单选题】
25T客车逆变电源为空调、电加热器以及其他车载交流380V用电设备供电,变压器为_______用电设备供电。___
A. AC220V
B. DC110V
C. AC380V
D. DC48V
【单选题】
TCP4-008/600[L]型DC110V充电机微机板指示灯具有一定的含义:如果VL0灭,VL1亮表示_______。___
A. IGBT保护
B. 变压器原边过流
C. 系统过热
D. 接触器KM2故障
【单选题】
TCP4-008/600[L]型DC110V充电机微机板指示灯具有一定的含义:如果VL0灭,VL2亮表示_______。___
A. IGBT保护
B. 变压器原边过流
C. 系统过热
D. 接触器KM2故障
【单选题】
25T型客车单相逆变器当输入电压高于_______时,逆变器输入过压保护动作,停止输出。___
A. 220V±6V
B. 144V±6V
C. 250V±6V
D. 180V±6V
【单选题】
25T型客车单相逆变器共有_______对外接线,全部采用压接式接线端子。___
A. 6根
B. 8根
C. 10根
D. 12根
【单选题】
单相逆变器所有带电部分短接后对地电阻,输入与输出之间绝缘电阻须大于_______。___
【单选题】
BSP青藏车ROX的作用是_______。___
A. 绑线架
B. 电缆密封装置
C. 固定作用
D. 防湿
【单选题】
BSP青藏车在配线表中线束号前两位字母ET在车上代表_______。___
A. 一位端
B. 二位端
C. 车头
D. 车尾
【单选题】
BSP青藏车蓄电池箱侧面分线箱的开关为_______。___
A. 断路器
B. 隔离开关
C. 按钮
D. 刀开关
【单选题】
BSP青藏车蓄电池的额定容量为__________
A. 120A•h
B. 100A•h
C. 80A•h
D. 50A•h
【单选题】
BSP青藏车空调机组的新风温度控制器探头设在_______附近。___
A. 新风过滤网
B. 送风口
C. 回风口
D. 过渡风道下部
【单选题】
BSP青藏车餐车水箱由位于二位端顶部的_______的椭圆形不锈钢水箱及位于厨房走廊顶部100L梯形小水箱组成。___
A. 1000L
B. 1100L
C. 1200L
D. 1300L
【单选题】
BSP青藏车硬卧车中茶炉、洗脸室及厕所模块内的废水排到_______。___
A. 污水箱
B. 真空污物箱
C. 轨道
D. 地面
【单选题】
BSP青藏车制氧机控制系统有_______工作模式。___
【单选题】
BSP青藏车装窗时,要求气囊中气压低于_______大气压。___
A. 1个
B. 0.45个
C. 0.7个
D. 0.8个
【单选题】
标记速度为160km/h的客车运行_______[或距上次各级修程不超过2年]实施A3级检修。___
A. 40万km±10万km
B. 60万km±10万km
C. 80万km±10万km
D. 100万km±10万km
【单选题】
特快旅客列车遇特殊情况必须变更_______时,须经列车调度员准许,并预告司机。___
A. 变通进路
B. 基本进路
C. 迂回进路
D. 接发车进路
【单选题】
重大事故的调查期限为_______。___
A. 10日
B. 20日
C. 30日
D. 60日
【单选题】
事故等级分为特别重大事故、重大事故、_______和一般事故。___
A. 大事故
B. 较大事故
C. 险性事故
D. 责任事故
【单选题】
列车及调车作业中发生冲突、脱轨、火灾、爆炸、相撞,造成客运列车报废1辆或大破2辆以上的,为_______。___
A. 一般A类事故
B. 一般B类事故
C. 一般C类事故
D. 一般D类事故
【单选题】
关闭折角塞门发出列车或运行中关闭折角塞门的为_______。___
A. 一般A类事故
B. 一般B类事故
C. 一般C类事故
D. 一般D类事故
【单选题】
_______由铁道部组织事故调查组进行调查。___
A. 特别重大事故
B. 重大事故
C. 较大事故
D. 一般事故
【单选题】
铁道部、安全监管办的安全监察部门应在事故调查组工作结束后_______之内,根据事故报告,制作《铁路交通事故认定书》,经批准后,送达相关单位。___
A. 5日
B. 10日
C. 15日
D. 30日
【单选题】
客车、发电车火灾或爆炸其破损程度达到:内部烧损需要修换的面积达20m2[包括顶、端、侧、地、门板以及间隔板]时,视为_______的条件。___
A. 客车报废
B. 客车大破
C. 客车中破
D. 客车小破
【单选题】
修理费用超过该型动车组新车现价70%的,符合_______条件。___
A. 动车组报废
B. 动车组大破
C. 动车组中破
D. 动车组小破
【单选题】
25T型客车检修规程规定:用兆欧表测量电力配线,相对湿度小于60%时其绝缘电阻应_______。___
A. ≥2M
B. 为2~0.38M
C. ≥0.38M
D. ≥10M
【单选题】
运用客车中高度调整阀调整杆上翘不超过_______。___
A. 30°
B. 45°
C. 60°
D. 90°
【单选题】
25T型客车的装有_______GNZ120-[4]型蓄电池。___
A. 60节
B. 80节
C. 90节
D. 100节
【单选题】
空气弹簧橡胶堆、上盖不得有长度超过_______的裂纹。___
A. 10mm
B. 20mm
C. 30mm
D. 40mm
【单选题】
运用客车中集便装置中污物箱的真空度为_______。___
A. -55~-39kPa
B. -45~-29kPa
C. -35~-19kPa
D. -25~-9kPa
【单选题】
25T型客车的逆变器应可靠接地,可能触及的金属部件与_______的电阻应不大于0.1。___
A. 电气元件外露处
B. 外壳接地点处
C. 导线金属暴露处
D. N线
【单选题】
运用客车中集便装置中真空便器中冲水装置须作用良好,冲水时间约_______。[1.0分]___
A. 1~2s
B. 2~3s
C. 3~4s
D. 4~5s
【单选题】
25T型客车的逆变器在正常环境条件下,带电电路对地的绝缘电阻应大于_______。___
A. 20M
B. 10M
C. 15M
D. 50M
【单选题】
运用客车中轴温报警器同车同侧轴温显示温差不超过__________
【单选题】
主管段长和车间主任未按规定在“车统—181”上签字不超过2次的,在运用客车质量鉴定中属于管理部分_______问题。___
【单选题】
159.25T型客车的充电器输入输出电路_______。___
A. 必须隔离
B. 必须并联
C. 必须重联
D. 必须有明显标记
【单选题】
运行、检修及交接记录填写错误或漏项不超过3处的,在运用客车质量鉴定中属于管理部分_______问题。___
推荐试题
【多选题】
Which two storage controller configurations can be used with Virtual SAN? (Choose two.)___
A. SAS controllers in Passthrough mode
B. SAS controllers in RAID0 mode
C. SAS controllers in RAID1 mode
D. SAS controllers in RAID10 mode
【多选题】
Which three are requirements when using vMotion to move a virtual machine across vCenter Server systems? (Choose three.)___
A. Both vCenter Servers must be using Enhanced Linked Mode.
B. Both vCenter Servers must be in the same Single Sign-On Domain.
C. Time must be synchronized.
D. Duplicate VM MAC addresses must be configured.
E. Both vCenter Servers must have High Availability enabled on source and destination clusters.
【多选题】
Which two components can be used when configuring Enhanced Linked Mode? (Choose two.)___
A. vCenter Server Appliance
B. vRealize Operations Manager
C. vSphere Management Appliance
D. vCenter Server for Windows
【多选题】
An organization has a number of virtual machines that would benefit from Fault Tolerance. These include: <A single vCPU Apache Server> < A dual vCPU vCenter Server> < A quad vCPU SQL Server> <An eight vCPU Hadoop Server>. Which two virtual machines can be configured to use VMware Fault Tolerance? (Choose two.)___
A. Apache Server
B. vCenter Server
C. SQL Server
D. Hadoop Server
【多选题】
Which two badges are major badges in vRealize Operations? (Choose two.)___
A. Risk
B. Efficency
C. Workload
D. Faults
【多选题】
An administrator is deploying multiple Windows 2003 Virtual Machines from the same template. What two steps should be taken to avoid network conflicts? (Choose two.)___
A. Customize the guest operating system.
B. Install VMware Tools into the new virtual machines.
C. Copy the Microsoft Sysprep tools onto the vCenter Server system.
D. Ensure the e1000 vmnic is selected for each new virtual machine.
【多选题】
Which three conditions would prevent Storage I/O Control from being enabled on a group of datastores? (Choose three.)___
A. The datastores planned for the solution are used by different vSphere clusters.
B. A datastore planned for the solution is configured as a Raw Device Mapping file.
C. A datastore planned for the solution has three extents.
D. A datastore planned for the solution is configured as NFS.
E. The organization has an Enterprise license.
【多选题】
Which two actions are prerequisites to adding ESXi 6.x hosts to a vSphere Distributed Switch? (Choose two.)___
A. Verify that there is at least one Distributed Port Group on the Distributed Switch.
B. Verify that the Distributed Port Group have active uplinks configured in its teaming and failover policy.
C. Verify that the
D. istributed Switch has been configured with a Network Profile.
【多选题】
An organization has configured Distributed Power Management (DPM) on a vSphere 6 cluster. The organization wants to be alerted when an ESXi host has been powered down by DPM. Which two options represent the type and name of the alarm that would accomplish this? (Choose two.)___
A. DrsEnteringStandbyModeEvent
B. DrsEnteredStandbyModeEvent
C. Event-based
D. Condition-based
【多选题】
Which two allow for the disabling of Network Rollback operations? (Choose two.)___
A. Modifying the vpxd advanded configuration options and adding the config.vpxd.network.rollback key
B. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\vpxd.cfg file and adjusting the<rollback> xml tag
C. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\vpxd.cfg file and adjusting the <networkrollback> xml tag
D. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\firstboot\vpxd-service- spec.prop file and adjusting the <rollback> xml tag
【多选题】
An administrator is tasked with performing a vMotion migration of a virtual machine. The virtual machine is configured as follows: <vSphere Flash Read Cache (vFRC) enabled> <Is part of a Distributed Resource Cluster (DRS) Cluster> Which two statements are true? (Choose two.)___
A. Each ESXi host in the cluster supports multiple virtual flash resources.
B. Each ESXi host in the cluster supports one virtual flash resource.
C. DRS treats powered-on virtual machines with Flash Read Cache as having a preferred affinity to their current host and moves them only for mandatory reasons.
D. DRS treats powered-on virtual machines with Flash Read Cache as having a required affinity to their current host and does not move them.
【多选题】
An administrator is using the Host Failures to Tolerate Admission Control Policy for a vSphere High Availability ___ cluster. When configuring this setting on the cluster, the administrator sees this error message: <Insufficient resources to satisfy HA failover level on cluster > What are two likely causes for the error? (Choose two.)(AB)
A. The hosts in the cluster are disconnected.
B. A host in the cluster is displaying an HA error.
C.
D. istributed Resource Scheduler has not been configured on the cluster.
【多选题】
What are two ways to identify TCP/IP stack information? (Choose two.)___
A. Using the vSphere Web Client
B. Using esxcli network ip netstack
C. Using esxcfg-netstack
D. Using the vSphere Client
【多选题】
Which two actions are required when enabling vFlash Read Cache for a virtual machine's virtual disk? (Choose two.)___
A. A value in the Virtual Flash Read Cache text box must be entered.
B. A Flash Resource Pool for Cache size reservation must be entered.
C. The Device backing and the block size must be configured.
D. The
E. nable virtual flash host swap cache check box must be selected.
【多选题】
What two IT infrastructure components are virtualized by vSphere Essentials? (Choose two.)___
A. Networks
B. Applications
C. Storage
D. Management
【多选题】
When attempting to access a virtual machine, an administrator is unable to login using the vSphere credentials. What two options are probable causes of the authentication failure? (Choose two.)___
A. The vSphere credentials have not been granted permissions.
B. The vSphere credentials are granted read-only permissions.
C. The vSphere credentials are granted no-access permissions.
D. The vSphere credentials are not a member of the local administrator group.
【多选题】
An administrator is performing a scripted installation of ESXi 6.x. In which three locations does the script need to be? (Choose three.)___
A. PXE Server
B. HTTPS
C. FTP
D. NFS
E. VVOLs Datastore
【多选题】
In order for a company to meet regulatory requirements, all ESXi 6.x Hosts must be configured to direct logs to a syslog server. What are two ways ESXi hosts can configured for this action? (Choose two)___
A. Use the esxcli system syslog command.
B. Edit them in the ESXi host Advanced System Settings.
C. From the Syslog collector user interface of the Web Client.
D. Syslog logging is not available for
E. SXi Hosts.
【多选题】
Which three actions can be executed when an alarm is triggered? (Choose three.)___
A. Send an email.
B. Send an SNMP trap.
C. Run a script or command.
D. Run an Orchestrator workflow.
E. Send a trigger to syslog.
【多选题】
An administrator is attempting to power on a virtual machine, but is unable to do so. Which two reasons are probable causes of the failure? (Choose two.)___
A. Storage access to the virtual machine swap file has been lost.
B. One of the virtual machine VMDK files is locked.
C. Virtual machine is running CentOS 7.0 64-bit.
D. Virtual machine has Hyper-Threading enabled.
【多选题】
An administrator has configured a host profile so that ESXi 6.x hosts will point to the corporate NTP server for time synchronization. The NTP server is located at 10.0.30.213, but time has not been synchronized properly across the ESXi hosts. The administrator reviews Host Profile settings as shown in the Exhibit. Which two steps are required to resolve the issue? (Choose two.)___
A. Correct the NTP server IP address.
B. Check the host for host profile compliance.
C. Remediate the host based on the updated host profile.
D. Change the NTP server to the FQDN as IP Addresses are not supported.
【多选题】
An administrator is attempting to migrate a large Hadoop virtual machine using vMotion. The administrator notices a delay when the machine is quiesced. The Hadoop virtual machine is processing many transactions a second to an in-memory database. Which two actions would help reduce the amount of time needed to perform a vMotion on this virtual machine? (Choose two.)___
A. Use multiple NICs for the vMotion vmkernel port.
B. Use a 10Gbps Network card for the vMotion vmkernel port.
C. Add an additional management network to help transmit the data quicker.
D. Disable Fault Tolerance before performing the vMotion.
【多选题】
An administrator is installing a new network card in an ESXi 6.x host that is part of a vSphere cluster. When the host is placed into maintenance mode, the vSphere Web Client displays the progress bar at 2% for over 30 minutes. Which two are likely reasons for this occurrence? (Choose two.)___
A. Maintenance mode is unable to migrate all virtual machines from the host.
B. There is a large number of virtual machines that must be migrated from the host.
C. VMware High Availability is in the process of reconfiguring the cluster.
D. Each virtual machine on the
E. SXi host must be reconfigured to recognize the new adapter.
【多选题】
Which two events happen when Distributed Resource Scheduler (DRS) is disabled? (Choose two.)___
A. The cluster's resource pool heirarchy and affinity rules are re-established when DRS is turned back on.
B. The cluster's resource pool hierarchy and affinity rules are not re-established when DRS is turned back on.
C. The cluster's resource pools are removed from the cluster.
D. The cluster's resource pools are removed from the cluster and assigned to the hosts.
【多选题】
Which two networking connection types can be configured on a virtual switch? (Choose two.)___
A. Virtual machine portgroups
B. VMkernel services (such as NFS, iSCSI, or vMotion) to the physical network
C. Web services over the Management Network
D. NFS and FCoE storage services
【多选题】
An administrator creates a DRS cluster of eight ESXi 6.x hosts. There are 10 virtual machines balanced across the hosts. An attempt to place the first host into maintenance mode fails. What are two reasons that the host failed to enter maintenance mode? (Choose two.)___
A. The DRS cluster Automation Level is set to Partially Automated mode.
B. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Should run on hosts in group.
C. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Must run on hosts in group.
D. One of the virtual machines on the
E. SXi Host entering maintenance mode is configured with an individual Automation Level set to Partially Automated.
【多选题】
When modifying a vApp, which two vSphere entities can be added? (Choose two.)___
A. A resource pool
B. A network pool
C. A vApp
D. A folder
【多选题】
From which two locations in the inventory hierarchy can you deploy a virtual machine using a template? (Choose two.)___
A. Directly from the template.
B. From a compute resource.
C. From an existing virtual machine.
D. From a Datastore.
【多选题】
A company has decided to implement Virtual SAN within their vSphere 6.x environment. The Virtual SAN cluster will be composed of three ESXi 6.x hosts that are on the Virtual SAN Ready Node list. Each ESXi host includes: <Two SAS Controllers that support Passthrough Mode> < Four Solid State Drives (SSDs) 1TB in size each> <20 SAS Magnetic Disks (MDs) 1TB in size each> <The SSDs and MDs are evenly split between the two SAS controllers>. The company will pilot a Virtual SAN cluster utilizing VMware best practices while maximizing storage capacity. The Virtual SAN cluster will use Manual Mode. Which two Disk Group configurations would meet the stated configuration requirements? (Choose two.)___
A. 4 disk groups with 1 SSD and 5 MDs each
B. 2 disk groups with 1 SSD and 7 MDs each
C. 2 disk groups with 2 SSDs and 7 MDs each
D. 2 disk groups with 1 SSD and 10 MDs each
【多选题】
A physical Windows 2008 R2 Server is converted to a virtual machine using VMware vCenter Converter. Upon completion of the conversion and subsequent power on operation, the virtual machine fails to boot and the message below is observed in the Console of the virtual machine: <STOP 0x0000007B INACCESSIBLE_BOOT_DEVICE>. Which two potential issues may be causing this boot failure? (Choose two.)___
A. An incorrect SCSI controller was selected during conversion.
B. Incompatible software drivers were migrated into the virtual machine from the source machine.
C. The vmdk file backing the virtual machine was thick provisioned.
D. A snapshot was taken immediately after the conversion completed.
【多选题】
An administrator is configuring the Failover Order option on a vSphere Distributed Switch. Which two options should be used with IP-hash load balancing? (Choose two.)___
A. Active Uplinks
B. Standby Uplinks
C. Unused Uplinks
D. Override Failover Order
【多选题】
An administrator is configuring the Maximum Transmission Unit value on a vSphere Distributed Switch. Which two options are typical values for ESXi networking? (Choose two.)___
A. 1492
B. 1500
C. 9000
D. 9089
【多选题】
Which two configurable options apply to both virtual machine CPU and memory allocation? (Choose two.)___
A. Reservation
B. Shares
C. Resource Pool
D. Reserve All
【多选题】
When attempting to power on a Virtual Machine you observe the following error: <Cannot open the disk '/vmfs/volumes/volume/vm/vm-000002.vmdk' or one of the snapshot disks it depends on.> Which three actions will be the best solutions to address this problem? (Choose three.)___
A. Verify that the virtual machine's disk files are present.
B. Investigate the host and virtual machine log files.
C. Verify the vmdk descriptor files and if required, recreate them.
D. Delete the disk file preventing the power on operation.
E. Migrate or register the virtual machine to a different host.
【多选题】
An administrator has been tasked with enabling High Availability ___ on a cluster in a vSphere 6.x environment with default settings. The cluster configures properly and there are no errors. The next day when powering on a virtual machine, an error is presented: <Not Enough Failover Resources>. Which three scenarios are likely causes of this error message? (Choose three.)(CDE)
A. The default VM Monitoring Sensitivity is set too high.
B. There are not enough datastore heartbeat datastores configured by default.
C. The default slot size in the cluster is set too high.
D. There are virtual machines with large CPU reservations.
E. A host is in maintenance mode for a replacement of a failed Hard Drive.
【多选题】
vMotion can be performed between which three physical boundaries? (Choose three.)___
A. Between two vCenter Server Systems
B. Between two vSphere Distributed Virtual Switches
C. Between two vCenter Server Datacenter objects
D. Between two VMware NSX Layer 4 segments
E. Between two NFS datastores
【多选题】
An administrator configures vSphere Replication for a virtual machine and enables multiple point in time (PIT) instances under the recovery settings in the Configure Replication wizard. Which two statements are correct for vSphere Replication with multiple point in time instances enabled? (Choose two.)___
A. vSphere Replication retains a number of snapshot instances of the virtual machine on the target site based on the retention policy that you specify.
B. vSphere Replication uses the virtual machine's snapshot instances to define the target site Point in Time instance based on the retention policy that you specify.
C. vSphere Replication does not support virtual machines with snapshots.
D. vSphere Replication supports virtual machines with snapshots.
【多选题】
An administrator is virtualizing a physical application server and adding it to an existing multi-tiered vApp. The application license is currently tied to the physical NIC's MAC address, so the administrator needs to ensure the license will function properly in the virtual machine. Which two actions can the administrator take to satisfy this task? (Choose two.)___
A. Set the MAC address for the vNIC in the guest operating system.
B. Install the physical server's NIC into the ESXi host.
C. Configure the MAC address for the vNIC using the vSphere Web Client.
D. Assign the physical server NIC's MAC address in the vSphere Distributed Switch.
【多选题】
Which two Fibre Channel zoning options are supported with vSphere 6.x? (Choose two.)___
A. Single-Initiator
B. Single-Initiator-Single-Target
C. Multiple-Initiators-Single-Target
D. Multiple-Initiators-Multiple-Targets
【多选题】
An administrator is attempting to remove an ESXi 6.x host from a vSphere Distributed Switch (vDS). When the administrator attempts to remove the host, the following error is observed: <The resource '16' is still in use.> What three steps are needed to successfully remove the host from the switch? (Choose three.)___
A. Select Manage Ports on the vDS for the host.
B. Locate all ports currently in use on the vDS for the host.
C. Migrate or delete any vmkernel or virtual machine adapters associated with the switch.
D. Remove all network cards from the switch before trying to remove the host.
E. Create a standard switch for everything to be automatically be migrated to.