【单选题】
非电气化区段4信息移频自动闭塞,衰耗隔离电子盒的主要技术指标引线端子对机壳绝缘_______。[311010103]___
A. 大于25MΩ
B. 小于25MΩ
C. 大于30MΩ
D. 小于30MΩ
查看试卷，进入试卷练习
微信扫一扫，开始刷题
相关试题
【单选题】
电气化区段4信息移频自动闭塞，交流电源为正弦波，其电压波动范围不大于_______时应可靠工作。[311010101]___
A. 180V±20V
B. 200V±22V
C. 220V±22V
D. 240V±24V
【单选题】
电气化区段4信息移频自动闭塞,衰耗隔离电子盒的主要技术指标输入阻抗为_______。[331010103]___
A. 1.8kΩ～2.2kΩ
B. 2.3kΩ～2.5kΩ
C. 3.0kΩ～3.3kΩ
D. 4.0kΩ～4.5kΩ
【单选题】
电气化区段4信息移频自动闭塞, 衰耗隔离电子盒的主要技术指标引线端子对机壳绝缘_______。[311010103]___
A. 小于25MΩ
B. 大于25MΩ
C. 大于30MΩ 小于30MΩ
【单选题】
ZP.Y2-18型移频自动闭塞轨道电路在分路状态下、道碴电阻最大时、用0.06Ω标准分路电阻分路任一地点，均应使分路残压在接收盘滤入处小于或等于_______。[333050203]___
A. 90mV
B. 100mV
C. 110mV
D. 120mV
【单选题】
ZP.Y2-18型移频自动闭塞轨道电路在晴天做分路试验，用0.06Ω电阻线分路时，在接收盘的“接入”孔上测试，一般电压为几十毫伏，最大不应超过_______。[333050203]___
A. 90mV
B. 100mV
C. 110mV
D. 120mV
【单选题】
ZP.Y2-18型移频自动闭塞区间电源屏应提供48V±1V的稳定电压，杂音电压应小于_______。[321010104]___
A. 90mV
B. 95mV
C. 100mV
D. 120mV
【单选题】
移频发送盒分频器采用了四级分频，经四级分频器后输出信号的频率仅为输入信号频率的_______。[311010104]___
A. 1/2
B. 1/4
C. 1/8
D. 1/16
【单选题】
移频电源盒的稳压电源，杂音电压不大于_______。[321010104]___
A. 100mV
B. 150mV
C. 200mV
D. 300mV
【单选题】
UM71型无绝缘轨道电路自动闭塞，电源电压范围在直流_______时应可靠工作。[311010102]___
A. 24V
B. 28V
C. 30V
D. 38V
【单选题】
UM71型无绝缘轨道电路自动闭塞,SVA空芯线圈的电阻量应为_______。[331010103]___
A. 18.5mΩ±5.5mΩ
B. 20.5mΩ±7.5mΩ
C. 25.5mΩ±8.5mΩ
D. 30.0mΩ±9.5mΩ
【单选题】
ZPW-2000A型无绝缘移频轨道电路自动闭塞，室内各种配线应采用_______。[311030203]___
A. 阻燃线
B. 通信电缆
C. 信号电缆
D. 阻燃屏蔽线
【单选题】
ZPW-2000A型无绝缘移频轨道电路自动闭塞，室内电线、电缆布线禁止出现_______。[311030203]___
A. 一字状
B. 环状
C. 十字状
D. 交叉状
【单选题】
ZPW-2000A型无绝缘移频轨道电路自动闭塞，各种配线_______。[313030203]___
A. 不得有中间接头可以有绝缘破损现象
B. 不得有绝缘破损现象可以有中间接头
C. 不得有中间接头和绝缘破损现象
D. 可以有中间接头和绝缘破损现象
【单选题】
ZPW-2000A型无绝缘移频轨道电路自动闭塞，室内各种配线、与数据通信线共槽的线缆均应采用_______。[311030203]___
A. 阻燃线
B. 通信电缆
C. 信号电缆
D. 阻燃屏蔽线
【单选题】
ZPW-2000R型无绝缘移频轨道电路自动闭塞，电源电压在_______的范围内应可靠工作。[311010101]___
A. 40V±1V
B. 48V±1V
C. 53V±1V
D. 55V±2V
【单选题】
ZPW-2000R型无绝缘移频轨道电路自动闭塞，信号机械室内部的各种配线全部采用_______。[311030203]___
A. 阻燃线
B. 通信电缆
C. 信号电缆
D. 阻燃屏蔽线
【单选题】
ZPW-2000R型无绝缘移频轨道电路自动闭塞，信号机械室内部的各种配线，与数据通信线共槽的线缆均应采用_______。[311030203]___
A. 阻燃线
B. 通信电缆
C. 信号电缆
D. 阻燃屏蔽线
【单选题】
非电气化区段微机交流计数电码自动闭塞设备与电气化区段设备相比,无_______。[322010203]___
A. 分频器
B. 滤波器
C. 干扰抑制器
D. 分频器,滤波器,干扰抑制器
【单选题】
电气化区段微机交流计数电码自动闭塞设备,在交流电源为正弦波,电压波动范围在_______下应可靠工作。[331010101]___
A. 不大于220V±33V
B. 不小于220V±33V
C. 不大于240V±40V
D. 不小于240V±40V
【单选题】
电气化区段微机交流计数电码自动闭塞设备,在交流电源为正弦波,频率范围在_______下应可靠工作。[331010101]___
A. 50Hz±1Hz
B. 70Hz±1Hz
C. 75Hz±1Hz
D. 85Hz±1Hz
【单选题】
电气化区段微机交流计数电码自动闭塞设备,不平衡电流_______。[322010101]___
A. 不大于25A
B. 不小于25A
C. 不大于50A
D. 不小于50A
【单选题】
电气化区段微机交流计数电码自动闭塞设备,发码器U3的6脚应为2kHz±0.5kHz方波,幅值_______。[311010103]___
A. 不大于4V
B. 不小于4V
C. 不大于8V
D. 不小于8V
【单选题】
ZPW-2000A型无绝缘移频自动闭塞在收到11.4Hz电码后，控制信号机点_______灯。[311010201]___
【单选题】
ZPW-2000A无绝缘移频自动闭塞系统发送器共采用_______CPU同时工作。[321010103]___
【单选题】
非电气化区段4信息移频轨道电路用0.06Ω标准分路电阻线在轨道电路不利处所分路时，接收设备的限入残压不大于_______。[333010101]___
A. 0.1V
B. 0.5V
C. 5V
D. 6.2V
【单选题】
ZPW-2000A无绝缘移频自动闭塞系统主轨道调谐区分路死区不大于_______。[311010103]___
【单选题】
ZPW-2000A型轨道电路的发送器负载为400Ω时，其输出功率_______。[321010103]___
A. 120W
B. 100W
C. 90W
D. 70W
【单选题】
ZPW-2000A型轨道电路的发送器低频频偏为_______。[331010103]___
A. ±7Hz
B. ±9Hz
C. ±11Hz
D. ±13Hz
【单选题】
ZPW-2000A无绝缘移频自动闭塞系统补偿电容引接线与钢轨要可靠连接，塞钉与钢轨间电压降应小于_______。[311010101]___
A. 5mV
B. 9mV
C. 15mV
D. 20mV
【单选题】
ZPW-2000A设备系统防雷室外防雷地线电阻要严格控制在_______以内。[323010103]___
A. 10Ω
B. 15Ω
C. 20Ω
D. 25Ω
【单选题】
ZPW-2000A无绝缘轨道电路，当长度超过_______时，主轨道需要加装补偿电容进行补偿。[323010103]___
A. 200m
B. 300m
C. 400m
D. 500m
【单选题】
ZPW-2000A无绝缘轨道电路分路状态在最不利条件下，主轨道任意一点采用0.15Ω标准分路线分路时,“轨出1”分路电压应不大于_______,轨道继电器可靠落下，在调谐区内分路时轨道电路存在死区段。[323010101]___
A. 110mV
B. 120mV
C. 130mV
D. 140mV
【单选题】
ZPW-2000A无绝缘轨道电路应能实现全程断轨检查，主轨道断轨时,“轨出1”电压不大于_______,轨道继电器可靠落下。[322010101]___
A. 110mV
B. 120mV
C. 130mV
D. 140mV
【单选题】
ZPW-2000A无绝缘轨道电路应能实现全程断轨检查，小轨道断轨时, “轨出2”电压不大于_______,轨道继电器可靠落下。[323010101]___
A. 43mV
B. 53mV
C. 63mV
D. 73mV
【单选题】
ZPW-2000A无绝缘轨道电路分路状态在最不利条件下,在1700Hz轨道电路区段任意一处用0.15Ω标准分路线分路,短路电流不小于_______。[322010101]___
A. 400mA
B. 500mA
C. 600mA
D. 700mA
【单选题】
ZPW-2000A无绝缘轨道电路分路状态在最不利条件下,在2000Hz轨道电路区段任意一处用0.15Ω标准分路线分路,短路电流不小于_______。[322010101]___
A. 400mA
B. 500mA
C. 600mA
D. 700mA
【单选题】
ZPW-2000A无绝缘轨道电路分路状态在最不利条件下,在2300Hz轨道电路区段任意一处用0.15Ω标准分路线分路,短路电流不小于_______。[322010101]___
A. 400mA
B. 500mA
C. 600mA
D. 700mA
【单选题】
ZPW-2000A无绝缘轨道电路分路状态在最不利条件下,在2600Hz轨道电路区段任意一处用0.15Ω标准分路线分路,短路电流不小于_______。[322010101]___
A. 450mA
B. 550mA
C. 650mA
D. 700mA
【单选题】
ZPW-2000A无绝缘轨道电路防护盒边缘距钢轨内侧不得小于_______。[312030205]___
A. 1300mm
B. 1400mm
C. 1500mm
D. 1600mm
【单选题】
ZPW-2000A无绝缘轨道电路补偿电容参数在1700Hz区段的指标及范围是_______。[322010103]___
A. 40uF±2.0uF
B. 46uF±2.3uF
C. 50uF±2.5uF
D. 55uF±2.75uF
推荐试题
【多选题】
What are two ways to identify TCP/IP stack information? (Choose two.)___
A. Using the vSphere Web Client
B. Using esxcli network ip netstack
C. Using esxcfg-netstack
D. Using the vSphere Client
【多选题】
Which two actions are required when enabling vFlash Read Cache for a virtual machine's virtual disk? (Choose two.)___
A. A value in the Virtual Flash Read Cache text box must be entered.
B. A Flash Resource Pool for Cache size reservation must be entered.
C. The Device backing and the block size must be configured.
D. The
E. nable virtual flash host swap cache check box must be selected.
【多选题】
What two IT infrastructure components are virtualized by vSphere Essentials? (Choose two.)___
A. Networks
B. Applications
C. Storage
D. Management
【多选题】
When attempting to access a virtual machine, an administrator is unable to login using the vSphere credentials. What two options are probable causes of the authentication failure? (Choose two.)___
A. The vSphere credentials have not been granted permissions.
B. The vSphere credentials are granted read-only permissions.
C. The vSphere credentials are granted no-access permissions.
D. The vSphere credentials are not a member of the local administrator group.
【多选题】
An administrator is performing a scripted installation of ESXi 6.x. In which three locations does the script need to be? (Choose three.)___
A. PXE Server
B. HTTPS
C. FTP
D. NFS
E. VVOLs Datastore
【多选题】
In order for a company to meet regulatory requirements, all ESXi 6.x Hosts must be configured to direct logs to a syslog server. What are two ways ESXi hosts can configured for this action? (Choose two)___
A. Use the esxcli system syslog command.
B. Edit them in the ESXi host Advanced System Settings.
C. From the Syslog collector user interface of the Web Client.
D. Syslog logging is not available for
E. SXi Hosts.
【多选题】
Which three actions can be executed when an alarm is triggered? (Choose three.)___
A. Send an email.
B. Send an SNMP trap.
C. Run a script or command.
D. Run an Orchestrator workflow.
E. Send a trigger to syslog.
【多选题】
An administrator is attempting to power on a virtual machine, but is unable to do so. Which two reasons are probable causes of the failure? (Choose two.)___
A. Storage access to the virtual machine swap file has been lost.
B. One of the virtual machine VMDK files is locked.
C. Virtual machine is running CentOS 7.0 64-bit.
D. Virtual machine has Hyper-Threading enabled.
【多选题】
An administrator has configured a host profile so that ESXi 6.x hosts will point to the corporate NTP server for time synchronization. The NTP server is located at 10.0.30.213, but time has not been synchronized properly across the ESXi hosts. The administrator reviews Host Profile settings as shown in the Exhibit. Which two steps are required to resolve the issue? (Choose two.)___
A. Correct the NTP server IP address.
B. Check the host for host profile compliance.
C. Remediate the host based on the updated host profile.
D. Change the NTP server to the FQDN as IP Addresses are not supported.
【多选题】
An administrator is attempting to migrate a large Hadoop virtual machine using vMotion. The administrator notices a delay when the machine is quiesced. The Hadoop virtual machine is processing many transactions a second to an in-memory database. Which two actions would help reduce the amount of time needed to perform a vMotion on this virtual machine? (Choose two.)___
A. Use multiple NICs for the vMotion vmkernel port.
B. Use a 10Gbps Network card for the vMotion vmkernel port.
C. Add an additional management network to help transmit the data quicker.
D. Disable Fault Tolerance before performing the vMotion.
【多选题】
An administrator is installing a new network card in an ESXi 6.x host that is part of a vSphere cluster. When the host is placed into maintenance mode, the vSphere Web Client displays the progress bar at 2% for over 30 minutes. Which two are likely reasons for this occurrence? (Choose two.)___
A. Maintenance mode is unable to migrate all virtual machines from the host.
B. There is a large number of virtual machines that must be migrated from the host.
C. VMware High Availability is in the process of reconfiguring the cluster.
D. Each virtual machine on the
E. SXi host must be reconfigured to recognize the new adapter.
【多选题】
Which two events happen when Distributed Resource Scheduler (DRS) is disabled? (Choose two.)___
A. The cluster's resource pool heirarchy and affinity rules are re-established when DRS is turned back on.
B. The cluster's resource pool hierarchy and affinity rules are not re-established when DRS is turned back on.
C. The cluster's resource pools are removed from the cluster.
D. The cluster's resource pools are removed from the cluster and assigned to the hosts.
【多选题】
Which two networking connection types can be configured on a virtual switch? (Choose two.)___
A. Virtual machine portgroups
B. VMkernel services (such as NFS, iSCSI, or vMotion) to the physical network
C. Web services over the Management Network
D. NFS and FCoE storage services
【多选题】
An administrator creates a DRS cluster of eight ESXi 6.x hosts. There are 10 virtual machines balanced across the hosts. An attempt to place the first host into maintenance mode fails. What are two reasons that the host failed to enter maintenance mode? (Choose two.)___
A. The DRS cluster Automation Level is set to Partially Automated mode.
B. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Should run on hosts in group.
C. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Must run on hosts in group.
D. One of the virtual machines on the
E. SXi Host entering maintenance mode is configured with an individual Automation Level set to Partially Automated.
【多选题】
When modifying a vApp, which two vSphere entities can be added? (Choose two.)___
A. A resource pool
B. A network pool
C. A vApp
D. A folder
【多选题】
From which two locations in the inventory hierarchy can you deploy a virtual machine using a template? (Choose two.)___
A. Directly from the template.
B. From a compute resource.
C. From an existing virtual machine.
D. From a Datastore.
【多选题】
A company has decided to implement Virtual SAN within their vSphere 6.x environment. The Virtual SAN cluster will be composed of three ESXi 6.x hosts that are on the Virtual SAN Ready Node list. Each ESXi host includes: <Two SAS Controllers that support Passthrough Mode> < Four Solid State Drives (SSDs) 1TB in size each> <20 SAS Magnetic Disks (MDs) 1TB in size each> <The SSDs and MDs are evenly split between the two SAS controllers>. The company will pilot a Virtual SAN cluster utilizing VMware best practices while maximizing storage capacity. The Virtual SAN cluster will use Manual Mode. Which two Disk Group configurations would meet the stated configuration requirements? (Choose two.)___
A. 4 disk groups with 1 SSD and 5 MDs each
B. 2 disk groups with 1 SSD and 7 MDs each
C. 2 disk groups with 2 SSDs and 7 MDs each
D. 2 disk groups with 1 SSD and 10 MDs each
【多选题】
A physical Windows 2008 R2 Server is converted to a virtual machine using VMware vCenter Converter. Upon completion of the conversion and subsequent power on operation, the virtual machine fails to boot and the message below is observed in the Console of the virtual machine: <STOP 0x0000007B INACCESSIBLE_BOOT_DEVICE>. Which two potential issues may be causing this boot failure? (Choose two.)___
A. An incorrect SCSI controller was selected during conversion.
B. Incompatible software drivers were migrated into the virtual machine from the source machine.
C. The vmdk file backing the virtual machine was thick provisioned.
D. A snapshot was taken immediately after the conversion completed.
【多选题】
An administrator is configuring the Failover Order option on a vSphere Distributed Switch. Which two options should be used with IP-hash load balancing? (Choose two.)___
A. Active Uplinks
B. Standby Uplinks
C. Unused Uplinks
D. Override Failover Order
【多选题】
An administrator is configuring the Maximum Transmission Unit value on a vSphere Distributed Switch. Which two options are typical values for ESXi networking? (Choose two.)___
A. 1492
B. 1500
C. 9000
D. 9089
【多选题】
Which two configurable options apply to both virtual machine CPU and memory allocation? (Choose two.)___
A. Reservation
B. Shares
C. Resource Pool
D. Reserve All
【多选题】
When attempting to power on a Virtual Machine you observe the following error: <Cannot open the disk '/vmfs/volumes/volume/vm/vm-000002.vmdk' or one of the snapshot disks it depends on.> Which three actions will be the best solutions to address this problem? (Choose three.)___
A. Verify that the virtual machine's disk files are present.
B. Investigate the host and virtual machine log files.
C. Verify the vmdk descriptor files and if required, recreate them.
D. Delete the disk file preventing the power on operation.
E. Migrate or register the virtual machine to a different host.
【多选题】
An administrator has been tasked with enabling High Availability ___ on a cluster in a vSphere 6.x environment with default settings. The cluster configures properly and there are no errors. The next day when powering on a virtual machine, an error is presented: <Not Enough Failover Resources>. Which three scenarios are likely causes of this error message? (Choose three.)(CDE)
A. The default VM Monitoring Sensitivity is set too high.
B. There are not enough datastore heartbeat datastores configured by default.
C. The default slot size in the cluster is set too high.
D. There are virtual machines with large CPU reservations.
E. A host is in maintenance mode for a replacement of a failed Hard Drive.
【多选题】
vMotion can be performed between which three physical boundaries? (Choose three.)___
A. Between two vCenter Server Systems
B. Between two vSphere Distributed Virtual Switches
C. Between two vCenter Server Datacenter objects
D. Between two VMware NSX Layer 4 segments
E. Between two NFS datastores
【多选题】
An administrator configures vSphere Replication for a virtual machine and enables multiple point in time (PIT) instances under the recovery settings in the Configure Replication wizard. Which two statements are correct for vSphere Replication with multiple point in time instances enabled? (Choose two.)___
A. vSphere Replication retains a number of snapshot instances of the virtual machine on the target site based on the retention policy that you specify.
B. vSphere Replication uses the virtual machine's snapshot instances to define the target site Point in Time instance based on the retention policy that you specify.
C. vSphere Replication does not support virtual machines with snapshots.
D. vSphere Replication supports virtual machines with snapshots.
【多选题】
An administrator is virtualizing a physical application server and adding it to an existing multi-tiered vApp. The application license is currently tied to the physical NIC's MAC address, so the administrator needs to ensure the license will function properly in the virtual machine. Which two actions can the administrator take to satisfy this task? (Choose two.)___
A. Set the MAC address for the vNIC in the guest operating system.
B. Install the physical server's NIC into the ESXi host.
C. Configure the MAC address for the vNIC using the vSphere Web Client.
D. Assign the physical server NIC's MAC address in the vSphere Distributed Switch.
【多选题】
Which two Fibre Channel zoning options are supported with vSphere 6.x? (Choose two.)___
A. Single-Initiator
B. Single-Initiator-Single-Target
C. Multiple-Initiators-Single-Target
D. Multiple-Initiators-Multiple-Targets
【多选题】
An administrator is attempting to remove an ESXi 6.x host from a vSphere Distributed Switch (vDS). When the administrator attempts to remove the host, the following error is observed: <The resource '16' is still in use.> What three steps are needed to successfully remove the host from the switch? (Choose three.)___
A. Select Manage Ports on the vDS for the host.
B. Locate all ports currently in use on the vDS for the host.
C. Migrate or delete any vmkernel or virtual machine adapters associated with the switch.
D. Remove all network cards from the switch before trying to remove the host.
E. Create a standard switch for everything to be automatically be migrated to.
【多选题】
Which two Virtual SAN related actions might start resynchronization of virtual machine objects? (Choose two.)___
A. Editing a virtual machine storage policy to increase the number of replicas.
B. Editing a virtual machine storage policy to reduce the number of replicas.
C. Editing a virtual machine storage policy to increase the number of disk stripes.
D. Editing a virtual machine storage policy to reduce the number of disk stripes.
【多选题】
An administrator is troubleshooting basic network connectivity issues. Which two scenarios are potential issues that this administrator might face? (Choose two.)___
A. The vSwitch is not attached to the correct physical network.
B. The portgroup is not configured to use correct VLAN.
C. Traffic shaping is configured incorrectly.
D. Jumbo frames is configured incorrectly.
【多选题】
Which three items should be validated prior to installing ESXi 6.x? (Choose three.)___
A. Remote Storage has been disconnected.
B. Installation media is available.
C. Server hardware clock is set to UTC.
D. Storage has been partitioned with a VMFS volume.
E. Network cards have been setup to use Jumbo
F. rames.
【多选题】
An administrator is performing an interactive installation of ESXi 6.x. Which three options are available for installation? (Choose three.)___
A. DVD
B. USB
C. PXE
D. Scripted
E. Auto Deploy
【多选题】
After installation of a host in your test environment, you need to move it to production. The only major change that needs to be made is that the hostname of the server needs to change. What are two ways that an administrator can change the host name without editing configuration files on the host directly? (Choose two.)___
A. Login to the Direct Console User Interface and change it from here.
B. Edit the Default TCP/IP Configuration from the vSphere Web Client.
C. Use the Ruby vSphere Client to send a script to the ESXi host that updates the hostname.
D. Update the information in DNS and the
E. SXi host will automatically update with these changes.
【多选题】
An administrator has unsuccessfully attempted several times to install an Operating System inside a virtual machine. The administrator finds that the installation fails at random intervals. Which two actions can be taken to resolve this issue? (Choose two.)___
A. Verify the md5sum and if invalid, download the installation files again.
B. Attempt the installation an additional time.
C. Attempt to use a different installation media or installation method.
D. Create a new virtual machine and attempt the installation with the existing media.
【多选题】
VMware tools is failing to install on a Microsoft Windows virtual machine. What are two possible situations that would prevent the installation? (Choose two.)___
A. The VMware tools installation media is corrupt.
B. The incorrect Operating System was selected in the virtual machine options.
C. The software prerequisites have not been installed.
D. The prerequisite services have not been started.
【多选题】
As part of a multisite Single Sign-On (SSO) deployment what two steps are required to ensure that a change to one Single Sign-On instance is propagated to the other instances? (Choose two.)___
A. Schedule a Replication Task on the primary instance
B. Select the first instance during the installation of subsequent instances
C. During the installation of each instance choose Linked-Mode
D. Enable Synchronize to Active Directory on each instance
【多选题】
You need to add an object to an existing vApp using the vSphere Web Client. How is this accomplished?___
A. Create an Object Inside the vApp.
B. Add an Object to a vApp.
C. Add an Object to the
D. atastore the vApp is located in.
【多选题】
Which three steps must be taken to use vSphere Update Manager 6.x to upgrade an ESXi 5.5 host to vSphere 6.x? (Choose three.)___
A. Download an ESXi Image.
B. Configure the vSphere Update Manager Download Service.
C. Create a baseline and attach it to the ESXi Host.
D. Scan the vCenter Content Library for the
E. SXi Image.
【多选题】
Which two options would allow a database administrator, with no access to the vSphere infrastructure, to connect to a virtual machine? (Choose two.)___
A. Use the Virtual Machine Remote Console (VMRC).
B. Use Remote Desktop Protocol (RDP) to connect.
C. Ask the vSphere administrator to grant permission to access the console through vCenter Server.
D. Ask the vSphere administrator to grant permission to access with the Horizon View Direct Connect Client.
【多选题】
Which three are architecture components of vRealize Operations? (Choose three.)___
A. Identity Server
B. Administrative Server
C. Analytics Server
D. Database Server
E. Connection Broker
