相关试题
【多选题】
在___情况下应立即利用消防车，通过水泵接合器向室内管网补水加压。
A. 消防泵不能启动
B. 消防泵出水量不能满足灭火要求时
C. 消防泵发生故障
D. 供水管网发生故障
【多选题】
消防用水可由___供给。
A. 市政给水管网
B. 天然水源
C. 游泳池
D. 消防水池
【多选题】
消防用水可由___供给。
A. 市政给水管网
B. 天然水源
C. 游泳池
D. 消防水池
【多选题】
下列___情况应设消防水泵结合器。
A. 高层厂房的室内消火栓给水系统
B. 设有室内消火栓给水系统的6层公共建筑，
C. 设有室内消火栓给水系统的5层仓库
D. 设有室内消火栓给水系统的高层民用建筑
E. 设有自动喷水灭火系统的高层民用建筑
【多选题】
对火灾发展迅速，可产生大量热、烟和火焰辐射的场所，可选择___探测器。
A. 感温
B. 感烟
C. 火焰
D. 可燃气体
【多选题】
以下哪类场所应当分别单独划分探测区域。___
A. 敞开或封闭楼梯间
B. 防烟楼梯间前室
C. 大型会议室
D. 走道、坡道、管道井、电缆隧道
【多选题】
采用可开启外窗自然排烟系统的部位和要求是___。
A. 长度不超过60m的内走道，开启外窗面积不应小于该走道面积的2%
B. 需要排烟的房间，可开启外窗面积不应小于房间面积的2%
C. 需要排烟的房间，可开启外窗面积不应小于房间面积的3%
D. 单层、多层民用建筑中的中庭、剧场舞台及高层建筑中空高度小于12m的中庭，有可开启的天窗或高侧窗的面积不应小于该中庭、剧场舞台楼地面面积的5%
E. 工业建筑与单层、多层民用建筑中其它场所，可开启外窗面积宜为该场所建筑面积
【多选题】
根据《高层民用建筑设计防火规范》（GB50045-95）的规定，采用自然排烟方式的部位，应满足下列要求___。
A. 防烟楼梯间前室，消防电梯前室可开启外窗面积不应小于2.00m2，合用前室不应小于3.00 m2
B. 靠外墙的防烟楼梯间每五层内开启外窗总面积之和不应小于2.00 m2
C. 长度超过60M的内走道可开启外窗总面积之和不应小于该走道面积的2%
D. 需要排烟的房间可开启外窗面积不应小于该房间面积的2%
E. 净空高度小于12m的无窗中庭
【多选题】
机械加压送风机的设置应根据___等因素确定。
A. 安全疏散
B. 供电条件
C. 封闭条件
D. 风量分配均衡
E. 新风入口不受火、烟威胁
【多选题】
机械排烟系统的排烟管道应符合下列___要求。
A. 管道应用非金属材料制作
B. 必须采用不燃材料制作
C. 应在其机房入口处设置有当烟气温度超过280度时能自行关闭的排烟防火阀
D. 吊顶内的排烟管道其隔热层应采用难燃材料制作，并应与可燃物保持不小于150mm距离
E. 在排烟支管上应设当烟气温度超过280度时能自行关闭的排烟防火阀
【多选题】
一类高层民用建筑和建筑高度超过32m的二类高层民用建筑的___等部位应设置机械排烟设施。
A. 长度超过20m的无直接自然通风的内走道
B. 长度超过60m的内道
C. 面积超过100平方米的且经常有人停留或可燃物较多的地上无窗房间或设固定窗的房间
D. 净空高度超过12m的中庭
【多选题】
火灾自动报警系统验收应包括对___的验收。
A. 火灾自动报警系统装置
B. 灭火系统控制装置
C. 防火卷帘控制装置
D. 防排烟控制装置
【多选题】
消防控制设备对室内消火栓系统应有___等控制、显示功能。
A. 控制消防水泵的启、停
B. 显示启泵按钮的位置
C. 显示消防水泵的工作、故障状态
D. 显示消火栓栓口的出水压力
【多选题】
火灾应急广播的设置应符合下列___要求。
A. 民用建筑内扬声器应设置在走道和大厅等公共场所，每个扬声器的额定功率不应小于3W
B. 扬声器数量应能保证从一个防火分区内的任何部位到最近一个扬声器的步行距离不大于25m
C. 走道内最后一个扬声器距走道末端的距离不应大于12.5m
D. 在环境噪声大于60dB的场所设置的扬声器，在其播放范围内最远点的播放声压级应高于背景噪声
【多选题】
室外消防给水系统按消防水压要求分___
A. 高压消防给水系统
B. 临时高压消防给水系统
C. 低压消防给水系统
D. 半高压消防给水系统
【多选题】
火灾探测器的选择，应符合___等规定。
A. 对火灾初期有阴燃阶段，产生大量的烟和少量的热，很少或没有火焰辐射的场所，应选择感烟探测器
B. 对火灾发展迅速，可产生大量热、烟和火焰辐射的场所，可选择感温探测器、感烟探测器、火焰探测器或其组合
C. 对火灾发展迅速，有强烈的火焰辐射和少量的烟、热的场所，应选择火焰探测器
D. 对火灾形成特征不可预料的场所，可根据模拟试验的结果选择探测器
E. 对使用、生产或聚集可燃气体或可燃液体蒸气的场所，应选择可燃气体探测器
【多选题】
火灾报警后，消防控制设备对防烟、排烟设施应有___等控制、显示功能。
A. 停止有关部位的空调送风，关闭电动防火阀，并接收其反馈信号
B. 关闭有关部位的防火门、防火卷帘，并接收其反馈信号，按顺序接通火灾警报装置和火灾应急广播
C. 启动有关部位的防烟、排烟风机和排烟阀等，并接收其反馈信号
D. 发出控制信号，强制电梯全部停在首层，并接收其反馈信号
E. 控制挡烟垂壁等防烟设施
【多选题】
属于闭式喷水灭火系统的是___
A. 湿式喷水灭火系统
B. 干式喷水灭火系统
C. 预作用喷水灭火系统
D. 雨淋喷水灭火系统
【多选题】
触发器件，主要包括___。
A. 点型火灾探测器
B. 手动火灾报警按钮
C. 消火栓启泵按钮
D. 线型火灾探测器
E. 消防电梯控制按钮
【多选题】
火灾自动报警系统一般由___四部分组成，复杂系统还包括消防控制设备。
A. 闭式喷头
B. 电源
C. 触发器件
D. 火灾报警控制装置
E. 火灾警报装置
【多选题】
火灾自动报警系统分为___种形式。
A. 区域报警
B. 集中报警
C. 控制中心报警
D. 通讯中心报警
【多选题】
二氧化碳灭火剂的灭火原理是___.
A. 稀释氧浓度
B. 窒息燃烧
C. 冷却
D. 化学反应
【多选题】
关于消防电梯的叙述正确的是___：
A. 消防电梯前室的门，应采用乙级防火门或具有停滞功能的防火卷帘。但合用前室的门不能采用防火卷帘。
B. 消防电梯的载重量不应小于800公斤。
C. 消防电梯的行驶速度，应按从首层到顶层的运行时间不超过2分钟计算确定。
D. 消防电梯轿厢的内部装修应采用不燃烧材料。
【多选题】
气体灭火系统不适用于扑救___火灾
A. 强氧化剂、含氧化剂的混合物
B. 能够自身提供氧而且在无空气的条件下仍能迅速氧化、燃烧的物质
C. 活泼金属
D. 不能自动分解的物质
【多选题】
火灾自动报警系统一般由___四部分组成，复杂的系统还包括消防控制设备。
A. 触发器件
B. 火灾报警装置
C. 火灾警报装置
D. 通讯装置
E. 电源
【多选题】
室内消火栓出水方向为___。
A. 向上
B. 向下
C. 与设置消火栓的墙面成90度角
D. 与设置消火栓的墙面成60度角
【多选题】
救生照明线适用于___。
A. 浓烟场所
B. 无照明场所
C. 水下作业
D. 有毒及易燃易爆气体环境
E. 高温火场
【多选题】
水喷雾灭火系统由___等组成。
A. 水雾喷头
B. 雨淋阀组
C. 闭式喷头
D. 管道
E. 供水设备
【多选题】
雨淋系统由___等组成。
A. 雨淋报警阀
B. 开式洒水喷头
C. 闭式喷头
D. 火灾报警装置或传动管
E. 管道、供水设施
【多选题】
室外消火栓的布置应符合___的规定。
A. 室外消火栓应沿道路设置
B. 甲、乙、丙类液体储罐区和液化石油气储罐区的消火栓应设置在防火堤外
C. 市政消火栓保护半径不应大于150m，间距不应大于120m
D. 室外消火栓的数量，应按建（构）筑物室外消防用水量和每个室外消火栓10-15L/s的消防用水量计算确定
E. 室外消火栓宜采用地上式消火栓，且室外消火栓距路边的距离不应大于2 m，距建筑物外墙不宜小于5m
【多选题】
火场供水的方法主要有直接供水、___。
A. 串联供水
B. 运水供水
C. 排吸器供水
D. 传递供水
【多选题】
战斗展开的形式分为___。
A. 准备展开
B. 提前展开
C. 预先展开
D. 全面展开
【多选题】
战斗实施是灭火战斗的主要环节。战斗实施主要包括救人、扑救火灾、保护和疏散物资、排烟以及___等任务。
A. 破拆
B. 供水
C. 救治伤员
D. 减少水渍
【多选题】
战斗结束后要进行下列工作：___。
A. 检查火场
B. 清点人数，整理装备
C. 补充灭火剂
D. 恢复执勤状态
【多选题】
运用战术原则的基本作战形式主要有：___。
A. 控制中消灭，防御中进攻
B. 重点设防
C. 重点守备
D. 打快攻、打近战
【多选题】
火情侦查的方法主要有：___。
A. 外部侦查
B. 内部侦查
C. 询问知情人
D. 仪器检测
【多选题】
医院火灾的特点主要有：___
A. 人员密集，化危品种类多
B. 疏散病人任务重，难度大
C. 烟雾多，火势蔓延快
D. 有些部位不宜用水扑救
【多选题】
灭火方法的具体运用主要包括堵截、夹攻、___、围歼等。
【多选题】
火灾现场总指挥根据扑救火灾的需要，有权决定下列事项：___
A. 使用各种水源
B. 截断电力、可燃气体和可燃液体的输送，限制用火用电
C. 划定警戒区，实行局部交通管制
D. 利用临近建筑物和有关设施
推荐试题
【单选题】
An administrator reports that the System Event log data is only available for 24 hours when reviewing the Hardware Status tab. Which condition could be responsible for the loss of data?___
A. A Reset event log was executed.
B. The statistical collection level was set to a value of 1.
C. The boot disk of the host is corrupt.
D. Syslog has been configured at the vCenter Server level.
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
【单选题】
An administrator is installing Windows into a virtual machine. The DVD has been mounted on the Host and configured for the virtual machine as shown in the Exhibit. Based on the exhibit, when the virtual machine is booted, why would it attempt to search for a PXE server? ___
A. The CD/DVD device is not connected.
B. The ISO is in the incorrect storage location.
C. The OS minimum requirements have not been met.
D. The CD/DVD device is not set to Client Device.
【单选题】
What component must be installed prior to deploying a vCenter Server in vSphere 6.x? ___
A. vCenter Identity Services
B. Platform Services Controller
C. vCenter Single Sign-On
D. Client Integration Plug-In
【单选题】
What is a valid plug-in status for a plug-in that has been added to a vSphere client? ___
A. Disabled
B. Unknown
C. Stopped
D. Installed
【单选题】
Users of an application are reporting performance issues. The following performance values are observed in the vSphere Web Client: <Host CPU utilization is 90%> <Virtual Machine memory utilization is consistently greater than 90% CPU Ready values are higher than 20%> What could be the cause of the application performance issue? ___
A. The host is lacking the CPU resources required to meet the demand.
B. The host is lacking the memory resources required to meet the demand.
C. The virtual machine is lacking the CPU resources required to meet the demand.
D. The virtual machine is lacking the memory resources required to meet the demand.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is re-provisioning an ESXi host and moving it to another datacenter. Which DCUI option should the administrator use to revert the system configuration to the default settings? ___
A. Reset System Configuration
B. Rebuild Default System Configuration
C. Revert System Configuration
D. Renew Default System Configuration
【单选题】
An administrator has just completed installing an ESXi 6.x host, but doesn't know what address has been configured. Where is the ESXi host IP address configured? ___
A. RVC console
B. Direct Console User Interface
C. vSphere Web Client
D. vSphere Client
【单选题】
When is it possible to place a VMFS5 datastore in maintenance mode? ___
A. When it is a member of a Storage DRS cluster
B. When it is a member of Virtual SAN cluster
C. When it is a member of a multi-extent datastore
D. When it is a member of a Virtual Volume
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
